Gerber Mp600 owners club ;)
-
@gregozedobe said:
I only just noticed the locking tabs on the Snap-On are different to the regular MP600s (and I have 3 of the Snap-On ones, got the first one back in 2016 ! )I also meant to mention that the first tool I know of that had the updated tabs was the MP600 Sight Tool(maybe 2014? That is when my U.S marked - updated Multi-Plier stamp - Sight Tool is dated). It seemed to coincide with the introduction of the fantastic huge combo-edge blade on the Sight Tool and Snap-On.
-
Alright. After a lot of restoration work, I'd say the cutter head is at 98% of being unused.
Here is a photo of the 600 Cable broken down. Note the heavily dinged up cutter.

After fine-filing(diamong coated needle files) the cutters back to the right profile, I replicated the Gerber finish on the jaws as closely as I can, but I haven't figured out a way to make it perfect yet. Close enough for this 600Cable Cutter to go into the collection. :)
The rest of the tools were wire-wheeled(varying brass or fine steel wheel) and oiled before reassembly.

Cutter Head close-up after reprofiling and finishing.

And a couple of shots with the MP650, which I also received a cable cutter head for.


-
@gerleatherberman said:
Alright. After a lot of restoration work, I'd say the cutter head is at 98% of being unused.Here is a photo of the 600 Cable broken down. Note the heavily dinged up cutter.

After fine-filing(diamong coated needle files) the cutters back to the right profile, I replicated the Gerber finish on the jaws as closely as I can, but I haven't figured out a way to make it perfect yet. Close enough for this 600Cable Cutter to go into the collection. :)
The rest of the tools were wire-wheeled(varying brass or fine steel wheel) and oiled before reassembly.

Cutter Head close-up after reprofiling and finishing.

And a couple of shots with the MP650, which I also received a cable cutter head for.


:ahhh :ahhh I want one so bad!!
-
Thank you, Nick!

@Sam Lim said:
:ahhh :ahhh I want one so bad!!Thank you much, Sam!

I feel the same about the Fisherman tools you bought. Just super cool!
When I saw the listing for the Cable Cutter, I bought it without hesitation. Thankfully the tool turned out collection worthy. No parts needed changing out and the cutter head looks good. :)
-
@gerleatherberman said:
Thank you, Nick!
Thank you much, Sam!

I feel the same about the Fisherman tools you bought. Just super cool!
When I saw the listing for the Cable Cutter, I bought it without hesitation. Thankfully the tool turned out collection worthy. No parts needed changing out and the cutter head looks good. :)
Exact same thought when I saw the fisherman. But so far when I see the cable cutter on the bay, it's always price at a premium.. Even when usually my thinking "is buy once and get it over with" , its still too high.. :-\
-
@Sam Lim said:
Exact same thought when I saw the fisherman. But so far when I see the cable cutter on the bay, it's always price at a premium.. Even when usually my thinking "is buy once and get it over with" , its still too high.. :-\Indeed. The Cable Cutters are usually insane. I paid $77 shipped for mine, so it was a decent deal. But, that being said, I put quite a bit of labor into the restoration. :ahhh
-
@gerleatherberman said:
Indeed. The Cable Cutters are usually insane. I paid $77 shipped for mine, so it was a decent deal. But, that being said, I put quite a bit of labor into the restoration. :ahhhI, would had jumped on it at $77... Usually I see them at $120 up........

-
Hopefully you can find one soon! And I hope you don't have to put as much work into it as I did on mine. :ahhh
-
@gerleatherberman said:
Hopefully you can find one soon! And I hope you don't have to put as much work into it as I did on mine. :ahhhI hope so too. I dun mind restorations at all. As long as the rust does not set in too bad. Sometimes I buy beat up MT just for fun of cleaning them up.. :) they have to be at a fitting price of course.
-
@Sam Lim said:
I hope so too. I dun mind restorations at all. As long as the rust does not set in too bad. Sometimes I buy beat up MT just for fun of cleaning them up.. :) they have to be at a fitting price of course.
Very true. I always go off of the condition of the plier head(if the head is salvageable) and the handle appearance.
I'm sure you know about the Gerber spotted fever as well.
I did take a gamble in the cutter tool. But, the tools as a whole had little noticeable Gerber fever and the fold out tools were unused.

-
@gerleatherberman said:

Very true. I always go off of the condition of the plier head(if the head is salvageable) and the handle appearance.
I'm sure you know about the Gerber spotted fever as well.
I did take a gamble in the cutter tool. But, the tools as a whole had little noticeable Gerber fever and the fold out tools were unused.

Yeah agree. Everything else can be easily replaced other than the pliers, in your case the precious cutter. The place I am at is known for humility... Not only Gerber fevers. Everything fevers..

-
@Sam Lim said:
Yeah agree. Everything else can be easily replaced other than the pliers, in your case the precious cutter. The place I am at is known for humility... Not only Gerber fevers. Everything fevers..
Indeed! :ahhh
About the Gerber fever, have you figured out a way to remove some of the spots without disturbing the satin finish yet, Sam? I've got a couple of early 600s that are in great shape, but have the fever. Whenever I try to remove the spots, the satin turns to polished spots. :ahhh
-
@gerleatherberman said:
Indeed! :ahhhAbout the Gerber fever, have you figured out a way to remove some of the spots without disturbing the satin finish yet, Sam? I've got a couple of early 600s that are in great shape, but have the fever. Whenever I try to remove the spots, the satin turns to polished spots. :ahhh
There's only one way to deal with the spot rusting.. The low light treatment.
Store all the MPs in low light area. Clean only under low light. U will not see the spots under low light. If u still sees them, you are doing it wrong again. Go lower light.

-
The problem with the Gerber Cable Cutter head is that the cutters were designed to cut very soft copper cables, so as soon as someone uses them on any kind of steel (doesn't have to be hard) it damages the cutting edge, and they aren't simple to re-contour to restore the cutting edge.
IMO they are really only fit for shelf queen duties ie for looking at as a different and unusual MT (and the buying public agreed, which is why Gerber no longer sells them). They look impressive with those great big cutter jaws, but weren't so good in actual use.
-
@Sam Lim said:
There's only one way to deal with the spot rusting.. The low light treatment.Store all the MPs in low light area. Clean only under low light. U will not see the spots under low light. If u still sees them, you are doing it wrong again. Go lower light.

Thanks, Sam! Honest and humorous.

-
@gregozedobe said:
The problem with the Gerber Cable Cutter head is that the cutters were designed to cut very soft copper cables, so as soon as someone uses them on any kind of steel (doesn't have to be hard) it damages the cutting edge, and they aren't simple to re-contour to restore the cutting edge.IMO they are really only fit for shelf queen duties ie for looking at as a different and unusual MT (and the buying public agreed, which is why Gerber no longer sells them). They look impressive with those great big cutter jaws, but weren't so good in actual use.
Thank you! Good information, Greg!

As easily as it was to remove a minute amount of material from the cutter during the restoration, I can see exactly what yiu mean. And indeed, the head definitely looks impressive, but as you said not practical. If I had one as my only MT with me, I'd be tempted to try cutting harder material.

A lot of the cable cutter probably got sent back to Gerber too, making them even more difficult to find. I feel lucky having gotten one I could bring back to decent collection-condition. :)
-
MP600 Cable Cutter close-ups.







-
MP600 - Camo MP600 and Trailrider Multi-Lock.
Camo MP600 Pro Scout.






Trailrider Multi-Lock - Early tool with Simonds file, and early Multi-Lock phillips driver.







-
someone had been really busy eh. :D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

