question about mp400
-
I had a look through mine as well.. Most have some gap, distance varies. Only one of them touches. The newer ones as GLBM mentioned, have a wider splay.
-
The gap might also be determined by how the pliers meet when they are out
if you know what I mean
. -
GLBM, Sam and Syncop8r:
Thanks for the reply's and info. I got these a couple of years ago used (the multiplier and MP400). Didn't pay much for them so I am reluctant to send the MP400 back to Gerber. I suspect also that I would have to mail them to the US and the cost would likely be more than I paid. I will keep an eye open for another pair locally or just use them as is. I have quite a few other multitools so these can be shelf queens without hurting my feelings. They still work properly just great for raising blisters I suspect.
Thanks again,
John.
-
John, Next week I'll see if putting some small washers between the lower plier studs and inside of the handles would be a good solution to the problem. Just send me a reminder if I don't post about it by Monday.

-
Sorry John, couldn't get the damn camera to focus
, but...With the pliers retracted, if you put a straight edge across the wider part of the handle, just below the engagement notch (pic 1) does it appear to sit flat, or is it the part where the cutout is noticeably higher? (pic 2)
Also, does it stay flat if you slide that straight edge further forward?


-
Al..... they must be the worst photos on the entire forum!

-
Probably...
And they were the best ones

-
Sorry!


-
@AimlessWanderer said:
Sorry John, couldn't get the damn camera to focus
, but...With the pliers retracted, if you put a straight edge across the wider part of the handle, just below the engagement notch (pic 1) does it appear to sit flat, or is it the part where the cutout is noticeably higher? (pic 2)
Also, does it stay flat if you slide that straight edge further forward?
Is this to check if the handles are bent from a gorilla grip?
I thought those were photos of deep sea fish.
:D -
@gerleatherberman said:
Is this to check if the handles are bent from a gorilla grip?
I thought those were photos of deep sea fish.
:D... or not tightly coined on the press. Makes more sense (to me) that the handles are the more likely issue rather than the plier casting. Is so, a tap with a slapping bat might fix it... ...
... and no, it was just a complete whelk holding the camera...
-

Good thought. That would be a better fix than my small washers.

-
Here is what Aimless was trying to capture in his photo.

If the engagement point is bulged outwards, it would cause the handles to be directed further inwards at the lock end. I am pretty sure that is what Aimless meant.

AW, please correct me if I am mistaken.
-
@gerleatherberman said:
Here is what Aimless was trying to capture in his photo.
If the engagement point is bulged outwards, it would cause the handles to be directed further inwards at the lock end. I am pretty sure that is what Aimless meant.

AW, please correct me if I am mistaken.
Yeah, pretty much. Thanks GBLM

If the steel either side of the slot isn't flat, but is angled up towards the opening, the handles will close more than they should. A bit of percussive maintenance should sort that out. Ideally it wants checking along the full length of the slot on both handles, it should be quite apparent if it hasn't been properly coined to 90o
If it does look flat, there is another check we can do too. We can pop off the spring clips of both John's and my MP400, and drop the plier heads out. In theory, they should both be the same width across the flat sections that slide against the inside of the handles.
-
Y'all let me know if any measurements are needed. I've got some 400s and calipers on hand to help.

-
I generally have about 2-3mm between the tools except for the odd nail nick bump here and there. No distortion on the handles such as Aimless
PhotographerWanderer is checking for.
-
Aimless - Thank you very much for the followup (despite the fish photos) :D
My MP400 has no bulges or distortions on the handles around the slot in which the pliers fit.
I've taken it apart - forgot the springs and had a search to find one.

The photo shows the pliers fully closed. Not sure if this helps but let me know if you need any other photos or measurements. Much appreciate the help.
John.
-
gerleatherberman - you have an overabundance of mp400's ;)
I will try to put a spacer in between the handles and back of the jaws before putting them back together. It will be later today as I have a few things on the go this morning. Will report back.
John.
-
Is the dimension across the tang of the pliers similar to mine?
(unfortunately, I couldn't get the pic as out of focus as last time
)
-
Doh!

That should be 27.65mm
Damn brainstem!

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login