Gerber Mp600 owners club ;)
-
@gerleatherberman said:

Very true. I always go off of the condition of the plier head(if the head is salvageable) and the handle appearance.
I'm sure you know about the Gerber spotted fever as well.
I did take a gamble in the cutter tool. But, the tools as a whole had little noticeable Gerber fever and the fold out tools were unused.

Yeah agree. Everything else can be easily replaced other than the pliers, in your case the precious cutter. The place I am at is known for humility... Not only Gerber fevers. Everything fevers..

-
@Sam Lim said:
Yeah agree. Everything else can be easily replaced other than the pliers, in your case the precious cutter. The place I am at is known for humility... Not only Gerber fevers. Everything fevers..
Indeed! :ahhh
About the Gerber fever, have you figured out a way to remove some of the spots without disturbing the satin finish yet, Sam? I've got a couple of early 600s that are in great shape, but have the fever. Whenever I try to remove the spots, the satin turns to polished spots. :ahhh
-
@gerleatherberman said:
Indeed! :ahhhAbout the Gerber fever, have you figured out a way to remove some of the spots without disturbing the satin finish yet, Sam? I've got a couple of early 600s that are in great shape, but have the fever. Whenever I try to remove the spots, the satin turns to polished spots. :ahhh
There's only one way to deal with the spot rusting.. The low light treatment.
Store all the MPs in low light area. Clean only under low light. U will not see the spots under low light. If u still sees them, you are doing it wrong again. Go lower light.

-
The problem with the Gerber Cable Cutter head is that the cutters were designed to cut very soft copper cables, so as soon as someone uses them on any kind of steel (doesn't have to be hard) it damages the cutting edge, and they aren't simple to re-contour to restore the cutting edge.
IMO they are really only fit for shelf queen duties ie for looking at as a different and unusual MT (and the buying public agreed, which is why Gerber no longer sells them). They look impressive with those great big cutter jaws, but weren't so good in actual use.
-
@Sam Lim said:
There's only one way to deal with the spot rusting.. The low light treatment.Store all the MPs in low light area. Clean only under low light. U will not see the spots under low light. If u still sees them, you are doing it wrong again. Go lower light.

Thanks, Sam! Honest and humorous.

-
@gregozedobe said:
The problem with the Gerber Cable Cutter head is that the cutters were designed to cut very soft copper cables, so as soon as someone uses them on any kind of steel (doesn't have to be hard) it damages the cutting edge, and they aren't simple to re-contour to restore the cutting edge.IMO they are really only fit for shelf queen duties ie for looking at as a different and unusual MT (and the buying public agreed, which is why Gerber no longer sells them). They look impressive with those great big cutter jaws, but weren't so good in actual use.
Thank you! Good information, Greg!

As easily as it was to remove a minute amount of material from the cutter during the restoration, I can see exactly what yiu mean. And indeed, the head definitely looks impressive, but as you said not practical. If I had one as my only MT with me, I'd be tempted to try cutting harder material.

A lot of the cable cutter probably got sent back to Gerber too, making them even more difficult to find. I feel lucky having gotten one I could bring back to decent collection-condition. :)
-
MP600 Cable Cutter close-ups.







-
MP600 - Camo MP600 and Trailrider Multi-Lock.
Camo MP600 Pro Scout.






Trailrider Multi-Lock - Early tool with Simonds file, and early Multi-Lock phillips driver.







-
someone had been really busy eh. :D -
I had the very same model camo Pro Scout and the paint so easily chipped off that I was left with a steel one. No biggie - it was a high quality plier and I used the heck out of it. I’m still in awe of how tough these pinchies actually are :hats off:
-
@Sam Lim said:
someone had been really busy eh. :DThanks, Sam!

Busy indeed.
@sawman said:
I had the very same model camo Pro Scout and the paint so easily chipped off that I was left with a steel one. No biggie - it was a high quality plier and I used the heck out of it. I’m still in awe of how tough these pinchies actually are :hats off:So true. Gerber painted finishes are really crappy, but the tool is a beast for sure. A lot of people don't know how much abuse a Pinchy can take. :ahhh
-
@gerleatherberman said:
Thanks, Sam!
Busy indeed.
So true. Gerber painted finishes are really crappy, but the tool is a beast for sure. A lot of people don't know how much abuse a Pinchy can take. :ahhh
Not comparing apples and oranges but I see the prices appear more reasonable than certain competitors..... significantly
-
Indeed. The MP600 Basic and Pro Scout are two of the best pliers based tools made. For the money($40-$50), the 600 is about as good of a deal as one can get. It is the only tool I know of that can operate maintenance free for over a year or more. :ahhh
-
Grind happy. Arrow tip Mp600. :D


-
Very nice work, Sam!

-
@gerleatherberman said:
Very nice work, Sam!

-
Carrying the mod I dubbed the MP6000 today.
Non-standard features are knifeless, two tone, integral cutters (which I don't think they sell anymore), wood saw, diamond file, awl, much better can opener (from a Strata), and tweezers. Excellent tool in my opinion, and all it needs to round it off is a traditional folder, for a fully capable combo that you can pretty much carry anywhere. Some of my knifeless mods need a little extra back up (the Fuse and Diesel mods need pairing with something that has a can opener), but a regular slippie is the only companion this needs.

-
Excellent custom 600, AW!

They do still make the needle nose in non-replaceable, but not the BN.
I had never considered the Strata combo too, but it makes sense seeing it there. :)
-
@gerleatherberman said:
Excellent custom 600, AW!
They do still make the needle nose in non-replaceable, but not the BN.
I had never considered the Strata combo too, but it makes sense seeing it there. :)
Thanks mate

The Strata can opener is one of the best can openers on any multitool IMHO. It's a thin but strong opener which pierces and cuts easily, and the grinding on the hook part gets hold of the underside of the lip better than most.
The saw on this came from a Strata too, which is slightly slimmer than a regular MP400/MP600 tool. The MP700 tweezers were the perfect thickness to take up the slack, as well as adding the extra function.


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login