Modding a Charge AL
-
Here is part 1 of the mod.

I've replaced the scissors and eyeglass tool with another bit driver. Went well aside from the panic after assembly when discovering an unused washer (I took out 3 tools and put in 2, duh!). The new bit driver (on side of flathead driver) is catching very slightly on the lip of the lock at the beginning of opening. The other one doesn't do that. Can someone tell me what I've done wrong?
A friend is sending me a pair of SAK 91mm scissors to put in place of the serrated blade. Here's to hoping that it goes well!
-
Looking good. Not sure what you mean about catching the lock when you first open it. Is it hanging up?
-
@ducttapetech said:
Looking good. Not sure what you mean about catching the lock when you first open it. Is it hanging up?Yeah, just very slightly. You can see on the backside of the hinge where it is flat rather than rounded? That edge is what's catching on the lock very slightly, just enough for it not to be perfectly smooth on rotating the tool out.
-
Gotcha. Does not sound like anything you done. Probably the bit holder might have been milled just a little off. Should be able to rounds it off pretty ease and polish back smooth.
-
@ducttapetech said:
Gotcha. Does not sound like anything you done. Probably the bit holder might have been milled just a little off. Should be able to rounds it off pretty ease and polish back smooth.Cool, should wear in then.
-
I have to apologise, it's been almost two years!
I finally got round to part 2 of the mod! Finally my Charge AL is how I always wanted it. Perfect!

The observant will already have worked it out.

A kind soul on another forum provided the donor SAK scissors. They dropped right it after having the hole drilled out courtesy of a metal shop. It's even OHO! I will file the butt of the pivot down to engage the lock when open some time when I'm bored, it's really not urgent, there is plenty friction and it locks at the half stop anyway so can't close on my hand at all.

...and here is the final tool. Two bit tools to hand like I had on my Skeletool, a flat head/pry bar and nice big scissors ready to hand rather than tucked away instead of the serrated blade I neither use or want. The eyeglass tool also had to go. Won't be missed. I have a Rambler on my keychain if I should ever have the need of that function.
Thoughts? This was the mod that brought me first to the forum two years ago, creating this thread, to see if it was possible. Thank you!
-
Very nice.

Did you consider an awl? Or dedicated Phillips driver? (Both from the LM Blast line.)
Do the scissors catch on the pin-thing that locks blades shut? I filed down this piece on my modded Wave.
With 4 bit driver heads on board already, you could modify the large flat head into a chisel blade / scraper type tool.
-
Very nice pomz
It has a great tool compliment and can be carried by itself and have everything a person should need in regular day to day life

SAK scissors really are the best
LM scissors are fine but having them outside and ready to use is much more handy as well 
-
@BePrepared said:
Very nice.
Did you consider an awl? Or dedicated Phillips driver? (Both from the LM Blast line.)
Do the scissors catch on the pin-thing that locks blades shut? I filed down this piece on my modded Wave.
With 4 bit driver heads on board already, you could modify the large flat head into a chisel blade / scraper type tool.
I really don't need an awl in day to day life. If I really need one, I've got a Farmer in the BoB in the car. :)
I far prefer bits to dedicated. I have there a phillips #1 & 2 as well as a hex 4mm & 5mm, these are by far my most used heads. That together with the big flat and I can do pretty much anything at home or in work.
The scissors don't catch at all which is nice. :)
-
Nice work.

-
Anyone ever put a SAK saw in a Charge? I far prefer the Victorinox saw to the LM one which is draw cut only. Just been musing about the next mod for my Charge. :)
I'd also love a solution for the handles, I chew up my fingers constantly from the knurled screws when using the tool hard. Any ideas?
-
Saw should fit if the hole is enlarged to the side some, not too far though because you'll want to have the liner lock function.
Will probably have the same halfway stop thing like the scissors.
Swap out the knurled screws for torx ones off a Ti/TTi. -
@zoidberg said:
Saw should fit if the hole is enlarged to the side some, not too far though because you'll want to have the liner lock function.
Will probably have the same halfway stop thing like the scissors.
Swap out the knurled screws for torx ones off a Ti/TTi.I didn't realise the TTi had different screws. That's a great idea! I have to contact Loki to see if he has any. Thanks!
-
and on the way, thanks!
-
@pomsbz said:
I didn't realise the TTi had different screws. That's a great idea! I have to contact Loki to see if he has any. Thanks!I think you may have to check with Loki, if the torx for the tti are long enough for the ALs. The torx on the tti are sitting recessed in the TI scales. While the knurled ones are sitting on top of the AL scales..
-
Loki checked again for me and you're right, they don't fit. He refunded me, guy is a gentleman.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
