What did you use your Sak on today?
-
Last night I used the can opener on my CT41 to open some clam shell packaging, pulling it like a draw-knife until I could extract the item trapped inside. I could've used one of the two blades to open it, but I was curious to see if it would work without sharpening the back side of the can opener.
This morning I was thinking about the new MiniChamp I got in the mail yesterday and what I could use the cut and picker blade for. I wondered if I could use the unique blade design on it to act as a wire cutter/stripper. I’ve used the wire stripper on the cap lifter of my Explorer along with the main blade to strip larger wires, but wanted to see if this little powerhouse was up to the task. I got to work and found an old piece of Cat-5 cable, opened the cut and picker blade slightly and trapped the cable underneath it. Then, with a little bit of pressure on the top of the blade, I spun the MiniChamp backwards towards the knife pivot a few times. I opened the blade all the way and pulled on the end of the cable and the casing slid right off, exposing the four twisted pairs inside, unscathed. I might just have to add the MC to my work carry. -
Great uses Kraken

-
On my very first day of carrying my mint red OC Farmer, a coworker need help opening a can of peaches at work. It must be fate because I don't think I've needed to open a can in years. I was more than happy to oblige, especially since the Vic style can opener is the only one I can manage to use without spending an hour fiddling and cutting myself. The job took seconds.
My Farmer's first knife duty was to cut the paracord I needed to give it a proper fob.
It's been a good day thus far.
-
@Kraken said:
This morning I was thinking about the new MiniChamp I got in the mail yesterday and what I could use the cut and picker blade for.Congratulations on the new MiniChamp Kraken!

The Victorinox Minichamp is an amazing little knife. Both blades will take a shaving sharp edge and are big enough to cut open cardboard boxes or to cut the flaps off of boxes. They are also good for opening envelopes. If you get a small pocket steel, you can keep the edges sharp by touching them up regularly. The pocket steel just realligns the edges without removing any metal.
The cut and picker blade (also called the orange peeler) will cut open clamshell packaging very easily, and also peel oranges. Just hook the point on the under side of the tip in the plastic and pull the peeler toward you and it will zip right through the plastic.
The cuticle pusher also serves as a screwdriver, or can be opened to extend the handle when you are using either of the knife blades. scissors,or the orange peeler. It can also be used for light prying.
The nail file comes in handy and the tip of it can also be used on phillips screws that are too big for the
smaller magnetized phillips screwdriver on the bottle opener tip.The small magnetized phillips screwdriver is great for removing the small phillips screws on doors to battery compartments on handheld electronic devices.
The scissors are great for cutting out coupons or clipping loose threads on clothing.
There is also a small ruler with w screwdriver tip on it.
The Minichamp is so small you don't even know you are carrying it, but it is there when you need it.
I always have my alox MiniChamp in my pocket. :D
-
Wrong thread.
-
@Buzzbait said:
On my very first day of carrying my mint red OC Farmer, a coworker need help opening a can of peaches at work. It must be fate because I don't think I've needed to open a can in years. I was more than happy to oblige, especially since the Vic style can opener is the only one I can manage to use without spending an hour fiddling and cutting myself. The job took seconds.My Farmer's first knife duty was to cut the paracord I needed to give it a proper fob.
It's been a good day thus far.
Great use Buzz

-
@Buzzbait said:
On my very first day of carrying my mint red OC Farmer, a coworker need help opening a can of peaches at work. It must be fate because I don't think I've needed to open a can in years. I was more than happy to oblige, especially since the Vic style can opener is the only one I can manage to use without spending an hour fiddling and cutting myself. The job took seconds.Gotta love the Vic can opener!
Thanks VICMAN!

-
Recently used Jalox’s bottle opener to disassemble my keybar so that I can add an LM small bit driver... don’t have any action shots, but here’s the keybar all good to go...

-
Hey, that's a cool idea Jaya man

-
The holiday weekend saw my Farmer in continuous use, lifting caps and opening bags of weenies.


-
Thanks Matt...

-
Ripping some pieces of wood to start a fire in wood stove
-
Great uses Buzz and PMargo

-
Cleaning lint and crud out of my Soldier with the PTC awl.

-
Good job gs

-
Popped open a beer.

-
Nice one Sos

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
