ZapWizard's Leatherman Free P4 Mods
-
That flat bit driver looks excellent

-
A bit driver...can opener and 1/4 inch driver....we are not worthy, not worthy!

-

I thought I had a good design for the thumb-tabs, and had SLS prototypes in hand last week.
The design was three small tabs held together by a sprue to reduce costs (Shapeways charges per-part)

In CAD these flat-head screws were supposed to be just a bit bigger than the slot, and they would secure the thumb tabs to the blade without any glue needed.
They are tiny #0-80x1/8L screws. But reality turned out that they fit through the slot, and were nearly impossible to thread into the tiny blind holes.

The prototypes did show they work pretty well. It makes it easier to open the blade, and easier to keep you thumb on one spot through the whole opening process.
However, I had to redesign them to figure out another securing method besides super glue.

This is the new design. It uses either #1-72 or M2 set screws. The set screws go almost the full length of the thumb tab. This time the hole they go into is tapered.
The top edge is set to that it should start to thread easily. Then the hole tapers down to the point that the hole is undersized. This along with a split in the back should make it so that the screw clamps the plastic sideways into the slot.
We will see once the second revision arrives.

The holster, driver, first run prints have all been ordered I didn't pay extra this time for rush processing, so it will be almost a month before I get them in my hands.
-
Wow. Very nice. Any guess on costs?
-
Pricing should work out to be $39 for the holsters (Same as my others), $25 for the bit holder, and $14 for the thumb tabs. Those prices are mostly Shapeways production costs.
-
@ZapWizard said:
Pricing should work out to be $39 for the holsters (Same as my others), $25 for the bit holder, and $14 for the thumb tabs. Those prices are mostly Shapeways production costs.OMG that is so reasonable for the bit holder. Any chance of designing a 1/4" hex bit holder for the wave/charge platform? If anyone can, you probably could.
-
:o Some very nice work, Zap

-
My production holster arrived today!
The good news is no design changes needed. Those seven previous prototypes paid off. The holster works perfectly. The tool snaps in with a satisfying click and is very secure with no rattling. It is slightly less secure when docked upside down due to the spring angle, but still good enough not to fall out if shaken upside down.
I did record a nice video showing off everything. But it turned out to be too blurry and with too much wind noisey. (Dead cat's don't work as well as they should). I will record another video once I get some time later next week.
The new production thumb tabs also arrived, along with the tiny set screws. They also fit perfectly and look great. The expanding set-screw lock worked like a charm.
Both of these are available on my Shapeways store. The link is in my signature.
The swappable bit holder also is here, but will require some drilling and more experimentation which I don't have time for this week. The bad news there is it probably will need to looe the bottle opener, as some Leatherman bits just don't have enough surface area at the back to fully engage with the magnet, and are weakly held right now.
-
That looks absolutely beautiful! :o :o :o

-
Everything looks good.
And I understand you've designed over/with what was already there but those thumb tabs are over the blade edge.
Having experienced this from some well known knife brands, it's something I choose to move away from. -
@zoidberg said:
And I understand you've designed over/with what was already there but those thumb tabs are over the blade edge.
Having experienced this from some well known knife brands, it's something I choose to move away from.
I am not sure what you mean by "over the blade edge". The tabs are all within the profile of the blade. And other than the main blade: They are all just barely larger than the thumb opening they go into. None of them extend more than a fraction of a millimeter past the back of the blade, so they won't interfere with other tools.
If you meant they rise above the scales on the tool. Currently they rise just 0.7mm above the surface. Just enough to grip even with gloves, but not enough to snag on anything.
-
I am not sure what you mean by "over the blade edge". The tabs are all within the profile of the blade. And other than the main blade: They are all just barely larger than the thumb opening they go into. None of them extend more than a fraction of a millimeter past the back of the blade, so they won't interfere with other tools.
If you meant they rise above the scales on the tool. Currently they rise just 0.7mm above the surface. Just enough to grip even with gloves, but not enough to snag on anything.
I mean it interrupts the line between the edge and the back of the blade.
When cutting the thumb tab will snag.
IMO this reduces the effective length of the blade or saw. -
Depends on what you're cutting. They wouldn't interfere with rope cutting, tube cutting, zip tie cutting, etc. The only thing I do that it would shorten the effective length of the blade is cutting fruit, and I rarely cut fruit with an MT blade. Maybe wood carving in some respects.
In fact, the thumb tabs would make it more comfortable to put your thumb on the spine of the blades. :)
I'm ordering a set of thumb tabs in white this weekend.

-
ZapWizard, those are really good -looking, well-designed accessories you made...kudos to you Sir! Will you consider doing the thumb tabs and sheath for the gen2 and 3 Waves? I'll be interested in two sets!
-
Check out his store. Lots of cool tool accessories. :)
-
@zoidberg said:
I mean it interrupts the line between the edge and the back of the blade.
When cutting the thumb tab will snag.
IMO this reduces the effective length of the blade or saw.I definitely agree for the saw. And honestly, I didn't even think about it. Other than the saw I have never used the full depth/length of any blade myself.
@gerleatherberman said:
I'm ordering a set of thumb tabs in white this weekend.
FYI: Nylon is an absorbent material. Lighter colors will show dirt quite quickly.
@Juan el Boricua said:
ZapWizard, those are really good -looking, well-designed accessories you made...kudos to you Sir! Will you consider doing the thumb tabs and sheath for the gen2 and 3 Waves? I'll be interested in two sets!It is on my list of projects to tackle someday.
-
This project is awesome, very nice work Sir

-
@SirVicaLot said:
This project is awesome, very nice work Sir


-
Some more
from me. Definitely interested in the bit holder...
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

