Screwdrivers?
-
They work really good but there is a learning curve. It's like riding a bike once you got it you got it. I did two houses switches and plugs with mine. Saved a lot of time.
-
@smiller43147 said:
My favorite is a ratchet bit driver. I assumed it was Craftsman, as that's what 90% of what I own is, but the name seems to have worn off. The handle swings out to the side, looks strange, but really ergonomic and you can develop a lot of torque.Smiller, that's a really cool handle, bet it works great!

-
I really love my Duralast screwdrivers I got at auto zone! I needed some drivers in my box and these fit the bill at 14.99 and then the guy the counter gave me a 10%discount so I got them for 13.50! I used the flathead to pop tabs on the guides for my brake pads, pry the plugs of my ignition coils, and turn the bolt on my air intake hose's clamp. Mine are different than the ones on the website because the flatheads have a hex shaped shaft on mine. I'd say these are about on par with Craftsman quality, at a great price plus, MADE IN USA!


-
My kitchen junk drawer screwdriver. Saves me a trip to the garage.

Sent from my SM-G960F using Tapatalk
-
**I usually keep a few multi-bit screwdrivers in my junk-drawer too, Mr. McKay. Mostly, Klein or Proto. **


-
Snap On and MAC hard handles. They can’t be beat.
-


Sent from my iPhone,dont expect too much[emoji85]
-



Sent from my iPhone,dont expect too much[emoji85]
-



Sent from my iPhone,dont expect too much[emoji85]
-
I have several pocket screwdrivers and my favorite is the USA-made SK Tools 85112:
404 Not Found
Discover the SK Tools Sktools.com, built for professional performance, lasting durability, and reliable results in the shop or garage.
SK Tools USA, LLC (sktools.com)
The combination slotted and Phillips P1 blade fits into a metal insert in the handle.
As is my habit, I glued a small, rare earth magnet to the end of the handle after filing the handle flat. I find that Gorilla Glue works better than Super Glue in this application.
I can rub the screwdriver blade against the magnet a few times to magnetize the blade. This is particularly handy when holding small screws for electrical outlet cover plates.

-
@parnass said:
I have several pocket screwdrivers and my favorite is the USA-made SK Tools 85112:
404 Not Found
Discover the SK Tools Sktools.com, built for professional performance, lasting durability, and reliable results in the shop or garage.
SK Tools USA, LLC (sktools.com)
The combination slotted and Phillips P1 blade fits into a metal insert in the handle.
As is my habit, I glued a small, rare earth magnet to the end of the handle after filing the handle flat. I find that Gorilla Glue works better than Super Glue in this application.
I can rub the screwdriver blade against the magnet a few times to magnetize the blade. This is particularly handy when holding small screws for electrical outlet cover plates.

The old Alexanders have had magnets on the top for years. Only problem is that the new ones have a plastic socket for the blade, while the old ones were steel. And whatever it is is susceptible to erosion from gas and diesel. That S&K looks like a great option at a decent price. The Alexanders, for years were freebie giveaways (as were most in my collection), but no one gives away tools, and to buy them are $3 each.
-
Other assorted pocket screwdrivers, many obtained as free promotional items.

-
@Vidar said:
Has anyone tried this kind of design by the way? I thought about getting one many times just to try, but somehow always forget :)- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
I have been using them for years, and I really like them the angle of the bencs and all that jazz is more I intuitive to use than you think. It's a very natural motion to me to loosen and tighten screws, plus the bend in the driver shaft is a good place for me to grip and apply torque. These definitely don't completely replace regular drivers but when mine got stolen I really missed them in my bag and now I have another pair.
-
Shown in the photo (top to bottom) are a Creative Products Easydriver, a smaller Speedball Easydriver, Craftsman 941464 B, Williams WRS-1, and Enderes KV-1.
The large Easydriver saves wear and tear on my wrist when building woodshop projects. I used the old Craftsman ratcheting screwdriver for miscellaneous home projects.
I now use the Enderes as a replacement for the Craftsman. The Craftsman has no bit storage and I don't want to keep walking back to the tool pile to retrieve the right bit for each job.
The bit is held into the Enderers driver shaft by the pressure of a ball bearing against the side of the bit. But, the tiny ball bearing kept falling out so I now use a small, round rare earth magnet to hold the bit in the driver.

-
this may be a bit more than what the op was asking for, but when i go for a screwdriver that is more than what my Surge can handle, i grab my kit that never lets me down.
it is my custom assortment of 6" long round shank bits with a Klein Switch driver handle and a Dewalt Gyroscopic power screwdriver. tucked in along side is a Klein 4in1 electronics screwdriver with phillips, flat and torx mix, some cobra style pliers and mini Klein cutters. (i guess you can tell i like Klein)
all wrapped in the smallest Veto pro pac tool pouch they make.
for facility maintenance, that kit does 90% of my job.
I cant say enough about the Dewalt power screw driver. i think it is severely under appreciated. most people have never seen them. but it can drive 3" screws into solid wood and has a fine touch and control that is made for locksmiths and electrical work. I have been using it every work day for 5 years and on the same 2 original batteries. best power screwdriver on the market that i have seen.
if i want more torque than it can handle or space is limited then the Klein Switch is the king.
the bits snap in tight with no play at all even after many years of use.oh, and the best thing about the Veto pouch is besides the great quality, i can hold it upside down and nothing falls out. even the bits stay firmly in place but easy to pull out due to a couple of small magnets that i dropped into the bottom of the pocket. you could hang over the side of a building with a harness and have it dangling from your side with no fear of anything dropping even when you pull other tools out. (sorry no video clip)


-
Nice but EVERYTHING always fell out of the one that I tried?
ALWAYS!So I use the MB1 instead and it is perfect for the same use as yours and the Dewalt is covered in there too!



@Walley said:
this may be a bit more than what the op was asking for, but when i go for a screwdriver that is more than what my Surge can handle, i grab my kit that never lets me down.
it is my custom assortment of 6" long round shank bits with a Klein Switch driver handle and a Dewalt Gyroscopic power screwdriver. tucked in along side is a Klein 4in1 electronics screwdriver with phillips, flat and torx mix, some cobra style pliers and mini Klein cutters. (i guess you can tell i like Klein)
all wrapped in the smallest Veto pro pac tool pouch they make.
for facility maintenance, that kit does 90% of my job.
I cant say enough about the Dewalt power screw driver. i think it is severely under appreciated. most people have never seen them. but it can drive 3" screws into solid wood and has a fine touch and control that is made for locksmiths and electrical work. I have been using it every work day for 5 years and on the same 2 original batteries. best power screwdriver on the market that i have seen.
if i want more torque than it can handle or space is limited then the Klein Switch is the king.
the bits snap in tight with no play at all even after many years of use.oh, and the best thing about the Veto pouch is besides the great quality, i can hold it upside down and nothing falls out. even the bits stay firmly in place but easy to pull out due to a couple of small magnets that i dropped into the bottom of the pocket. you could hang over the side of a building with a harness and have it dangling from your side with no fear of anything dropping even when you pull other tools out. (sorry no video clip)
-
Nice. and so shinny!
I have the MB1 as well. i know alot of people use them for misc. tools but I use it strictly for my meters, circuit testers and thermometers. i may get the MB2 soon because its a bit over loaded atm. and i have probes that barely fit.
I also have the original MC tech.
the tools i put in the MP1 seem to be just right for it, they all fit snug. even the pliers stay put because i put one handle through the D-loop. the only thing that has ever dropped out was the socket when i was whipping it around while showing someone how good it was lol.
for the tools that fit looser, you just have to take one small fridge magnet and jam it deep into the pocket.and nice to see another dewalt driver! I only know one other person that has one and he bought it after he tried mine.
-
I'm a bit driver fan myself and have accumulated possibly more than I strictly need. What I have that I like:

From left to right:
Wera Kraftform 821 (holds six bits; removable spring-loaded extensible blade with Rapidaptor)
Wiha System 6 (removable blade extends to varying lengths using ball detent locking system)
PB Swiss 8451.10-30 M
PB Swiss 6460 (Insider 1) (holds eight bits)
Wiha System 4 (takes 4mm precision bits; removable blade extends to varying lengths using ball detent locking system)
Wera 822 (takes 4mm precision bits)
Wera 815 (fixed Rapidaptor)
Wera 813
Felo Ergonic 438 stubby
All of these take standard 1/4" hex bits except where noted.I think each of these works very well for its intended uses (other than the PB Swiss Insider 1 which I only recently got and haven't used yet, so can't really comment). The Weras are my overall favourites; I don't think the 822 or the 815 are readily available though, which is a shame as there is a gap in their range between the Kraftforms which are big and weighty and the 813 which is tiny (75mm long).
For bits I like the Wera 1/4" bits and Wiha's 4mm precision bits the best of what I have tried. I've heard good things of the PB Swiss bits and will be interested to see how they hold up in comparison.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login