What did you just get?
-
So I’m trying my hand at paracord, only to discover that I need a needle with the hole at the end...pointing backwards. Something called a Permalok needle. Eventually tracked down a few sizes that I picked up today. Just a brass rod, rounded tip and tapped hole in the back to twist the paracord into. This lets you thread paracord for more difficult weaves without snagging. Not sure that I need the long one, maybe for a bigger project with lots of under-over work. Anyway, no more excuses not to create some more paracord work!

Also got a few small swivel shackles so I can make up another suspension setup. These shackles have a pull-back sliding latch, instead of a swing-away latch. Better as it does not push back on the item you’re trying to release.





-
Nice selection of tools Max

-
Thanks WS.
Now to make something with them. 
-
Look forward to see what you will make with them

-
Got dis today!
Charles.

-
Nice one CC

-
I'm not a fan of the "Hooters" logo. That's not my kind of thing. But the knife itself is in mint condition and I really like it.
Charles.
-
Would you be able to sand it off

-
I'm going to try some chemicals first. Something that will soften the paint but won't touch the stain. Probably start with mineral spirits and see if that works.
Charles.
-
Well, I had at it with a scraper, then chemicals, and that didn't do it so I sanded it. The area where the logo was got a bit lighter, and I went through the stain on the sharp edge by accident. Fortunately, I had a stain that was a close match. It darkened the lightened area somewhat, but not enough, and it fixed the area I went through completely. That part took stain readily. But unless I sand the whole thing down to bare wood, the old finish will not allow the new stain to penetrate. I'd rather have that area a little lighter than it end up being blotchy, so I quit while I was ahead. I think it looks quite nice, almost a natural variation in the wood, or handling wear. At any rate, it's better than a sleazy Hooters logo.
I love the heft of this knife. It's huge, but somehow it's not at all imposing. It looks like a big goofy swiss army knife... and it really is exactly that.
The pics below show a Wenger SwissBuck as a size comparison. I forgot to take a photo of the sides, but the 3 layers of the Wenger is as thick as just two layers of this Aitor.
Charles.


-
My Alox MiniChamp showed up, today.
Pony Express did good, for me, getting it here before the due date.

-
@ChopperCharles said:
Got dis today!Charles.
Is that a hook like on SAKs or a hoof pick?
-
@ChopperCharles said:
Well, I had at it with a scraper, then chemicals, and that didn't do it so I sanded it. The area where the logo was got a bit lighter, and I went through the stain on the sharp edge by accident. Fortunately, I had a stain that was a close match. It darkened the lightened area somewhat, but not enough, and it fixed the area I went through completely. That part took stain readily. But unless I sand the whole thing down to bare wood, the old finish will not allow the new stain to penetrate. I'd rather have that area a little lighter than it end up being blotchy, so I quit while I was ahead. I think it looks quite nice, almost a natural variation in the wood, or handling wear. At any rate, it's better than a sleazy Hooters logo.I love the heft of this knife. It's huge, but somehow it's not at all imposing. It looks like a big goofy swiss army knife... and it really is exactly that.
The pics below show a Wenger SwissBuck as a size comparison. I forgot to take a photo of the sides, but the 3 layers of the Wenger is as thick as just two layers of this Aitor.
Charles.
Looks good, Charles!

@PitCarver said:
My Alox MiniChamp showed up, today.Pony Express did good, for me, getting it here before the due date.
Very nice!

-
@Top-Gear-24 said:
Fisrt of all, over here, finding a rare or old tool does not happen very often, and if it happens it's usually because you just stumble upon something by pure luck.This story begins about 10 years ago, it must have been right before I joined this place when I walked into a small store to see if they had some Leatherman tools, since that was the only brand I bought back then, I knew about SAKs, but having owned a fake SAK as a child had me thinking all those red knives were cr*p ...
.Anyway, I found nothing special in that store, some standard Leatherman tools, and one odd looking Leatherman lookalike, which had to be a fake since it had a brand name on it which I'd never heard off before ... SOG
Years later I know a bit more about different brands and tools, I know that a fake SAK is not the same as a real SAK, and I know that SOG is indeed a real brand. And since I'm always thinking about ways to find some new "old" tools, that SOG tool from 10 years ago popped in my head, and it got me wondering, would it still be there ? Sure it will be long gone by now ... ? Going there will just be a big waste of my time, you'll see ...
Yesterday I decided I should just go there and see, and guess what was still there, in the same place I saw it 10 years ago (being the back of a small Leatherman display cabinet, turned to the wall ...) ... :o



These next days, I'll make topics for both of them in the SOG forum, and post some more pics of them there.
Looking at my unused examples(only the V.3 was NIB), it appears you have a V.2 with polished blunt nose. Is that correct?
Close-ups to see differences. Left to right: V.3(polished NN pliers head), V.2(polished BN pliers head), & V.1(sating BN pliers head - no lanyard ring and extra hole in the handle side).



-
@gerleatherberman: Here are some more pics of my Power Plier, these will make it easier to determine for sure which version I have ;).




-
Nice

-
@Top-Gear-24 said:
@gerleatherberman: Here are some more pics of my Power Plier, these will make it easier to determine for sure which version I have ;).




Version 2. My favorite. Great pics! :oFull polish, true blunt nose, large bolt section, and compound leverage. It(and the V.1) has no true competition in regards to the pliers function, as well as having one of the highest tool densities ever put into a factory MT.

-
Awesome find TG! Very nice!
Enviado de meu moto g(6) usando o Tapatalk
-
Just got the carbon fibre frame panels delivered

For my Kawasaki Z1000 motorbike

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login