91mm SAK mod 'Mountain Tinker'
-
Excellent mod and write up! Cool pics too
[It's not failure if you learn something from it]
-
-
Nice mod and detailed steps comis...

If I may add (for future mods), warm or hot water will do the scale removal trick... boiling water is way to riskier for the SAK and the person doing the mod. After drilling, the punch can be used to push the pins through the bushings and layers... if itβs hard to punch the pins, drill a little bit more... learned this trick based from experience and from other modders... good thing about this, less damage to the bushing...

-
@jaya_man said:
Nice mod and detailed steps comis...
If I may add (for future mods), warm or hot water will do the scale removal trick... boiling water is way to riskier for the SAK and the person doing the mod. After drilling, the punch can be used to push the pins through the bushings and layers... if itβs hard to punch the pins, drill a little bit more... learned this trick based from experience and from other modders... good thing about this, less damage to the bushing...

Good points!
I gonna experiment/research more to see what's the minimum hot water temperature to get the job done, and thank you for the reminder on the punch out trick, I too actually use sometimes after some dremeling. Original post edited to reflect these good pointers! 
-
My pleasure comis... just keeping the MTO spirit alive... All the things I learned about modding SAKs I got here in MTO... only appropriate to pass it along to others as well...
-
Thanks for sharing your experience.
-
-
Nice work! It looks great!!

Sent from my Redmi Note 5
-
@jaya_man said:
My pleasure comis... just keeping the MTO spirit alive... All the things I learned about modding SAKs I got here in MTO... only appropriate to pass it along to others as well...
I'd read some of your posts in the past, and thank you for sharing too! It is essentially what makes MTO great.Thanks for reading!

-
-
-
-
I just realized I've forgotten to put in hammer as essential tools!

I used a few hammers to peen and punch out the pivots.
The heavier 500g/17oz hammer is only used to punch out the pivot with a center punch, layer by layer, and I carefully monitored the shape of the pivot as I was punching them out. Any deformation of the pivot may marr the liner holes or get stuck and warp the liner, so I would try to file away any debris/deformation before punching them.
I got a 3.5oz(100g) and 5oz(150g) hammer, and I used them changeably for peening the 91mm. I practiced a few times on beater 91 and 93mm before attempting this mod, just to get a feel on how to peen. I know some folks here have some mad peening skill, but my newbie two cents worth are:
-
For smooth, flat installation of 91mm scales, we will probably need the rivet be completely flat and smooth on top of the bushing(pls see your bushings and take pictures before taking them apart). But no worries, 91mm peening is much, much easier than 93mm peening.
-
Ball peen hammer will 'move' the material, sort of expand the surface material, and give the appearance of 'dome' shape of the rivet. We don't really need that in 91mm per se since we need the rivet to be totally smooth within the bushing, but I do use ball peen anyway to 'fill up' the top of the bushings.
-
Flatter the ball peen/hammer face, smoother the hit on the rivet, and vice versa. If you use a small ball peen hammer with a really round ball peen, that obviously will leave a very visible 'dent' on the face of the rivet(part of the reason why ball peen will 'expand' the material). So for 91mm, you could basically get away with even using a flat face hammer.
-
With my 93mm peening practice, I know there is this balance/sweet spot we want to get to--On one hand, I would want to use flatter ball peen/flat face hammer to smooth the appearance, but that won't give the dome shape and flat face may hurt the aluminum scale easier. On the other hand, there is a tendency to try to use a really small round ball peen to avoid hitting the scale, but that would expend the surface quickly, and the edge of the dome may become too thin, and as you hammer the pivot down into the rivet, and eventually get so thin that it may even start to 'crack' at the edge as it touches the scale.
That's probably one of the reason why 93mm peening is difficult, how much length left for the optimal shape/function, what technique, etc. I am still too new and not successfully enough to make any real contribution here, but that's another story for another time. If anyone whom have done it in the past, please do feel free to chime in!

- I know some modder like to use a punch at the end of the process to ensure the material fit up the rivet bushing nicely. That is subjective, but if you felt there is not enough material inside the bushing to form a effective rivet, then I guess this is a good way to help.
Thanks for reading again!

-
-
-
Nice write-up comis!
This will come in handy should I ever have access to a drill press. -
-
@SirVicaLot said:
Nice write-up comis!
This will come in handy should I ever have access to a drill press.Actually, a drill press will be really nice to have to do a clean job, but I do agree with most folks that you don't actually need one to do a 91mm mod. A dremel or hand drill will actually be suffice.

-
Lovely mod! Great pics too. 
-
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better π
Register Login