SwissFlame - no fire
-
@burnside said:
I wonder if anyone has ever come up with a fix for the SwissFlame?
Spent a good part of an evening striping one. Initially thought the jet was blocked but turned out the valve inside the reservoir was stuck. Got it free but I’d already damaged the jet hole thinking it was blocked so gas was now releasing but not successfully lighting on piezo. Found a replacement donor jet from another no name jet lighter but managed to crack the ceramic shield so whole restore effort was abandoned. I can’t recommend trying a fix these unless you get access to a few and can cannibalizes parts. >:(


-
Wow fascinating! I've wanted to get mine to work but didn't want to take it apart. Thanks for giving it a try and giving us a glimpse of the inerds.
-
Sadly, even when the SwissFlame works, it has a great deal of trouble in cold weather....exactly when you would need it the most.
-
I had a working one. Sold it to another MTo member for about E 65. Don´t know its current status.
-
For those interested, here’s a description of how it works:
Pressing the thumb press exposes the burner while rocking a lever that pulls up the reservoir valve, releasing the butane that vaporizes in the tube below the jet that dog-legs around the back tool pivot.
At the same time, the thumb press loads the piezo spring, that trips at the bottom of the press, striking a small crystal that generates a short pulse of electricity of several hundred volts, enough to jump an air gap at the burner created by a small insulated wire that runs up from base of the piezo generator, grounding back to the piezo via the base of the burner.
The jet is a tiny hole finer than the tip of a needle, punched in a thin metal disk. The shape and size of this hole is critical as it must direct the escaping gas vertically up the burner tube to mix with air, ignited by the spark, creating the characteristic jet flame. Any contamination of this jet can upset this delicate setup, and trying to clear the hole with a pin or needle will only distort the hole, causing a misaligned flame or a complete failure of the burner to light.
Releasing the thumb lever closes the reservoir valve and the flame goes out, returning the lighter’s cover cap.
The flame strength is a function of the gas flow, regulated by a screw that surrounds the refilling value. This screw compresses a semi-permeable fiber washer inside the value, allowing controlled adjustment of the flow rate.
The burner/jet, piezo generator and reservoir value are all off-the-shelf components common to many jet-style burners. The plastic reservoir, metal thumb lever/cap and metal sleeve that slides over the whole lighter (creating the ‘tool’ layer) are custom-built components.
Filling the reservoir is done by inverting the lighter so that a pressurized butane canister can be press-fitted to the filling valve to dispense butane fluid (based on the canister having a higher pressure than the reservoir). A window in the reservoir shows the butane level (rather small capacity).
There are several design weaknesses, such as the sticking reservoir value (an internal brass rod inside the valve that I think is meant to be an invert cut-off safety), as shown in my 2nd picture above. The burner/jet combination appears sub-optimized, hence the lighting difficulty in some conditions. The wire from the piezo is just insulated at the top with a dip-coating (which can wear off causing a short and failure of the spark). And the butane reservoir is very small.
A bit of a waffle, but hopefully of some interest? :D
-
I see why the Idea was abandoned. Might as well just fit a mini Bic in a fat rear scale then. Hmm I wonder how rediculous that would look
-
That´s been done. Kind of.

-
I think it would be more fun to build a peanut-style lighter using your tray as a base?

-
@Max Stone said:
I think it would be more fun to build a peanut-style lighter using your tray as a base?Are those like tiny zippos? I was never a fan of the smell of that type of lighter and the leaking. A mini Bic would work for so long and super cheap to replace. I'm going to take some measurements.
-
@Syph007 said:
I see why the Idea was abandoned. Might as well just fit a mini Bic in a fat rear scale then. Hmm I wonder how rediculous that would lookCoast did that with a Wenger clone. It didn’t look bad and it works great, even 30 years later.... if you can find one without a cracked reservoir. The nylon was thin around the threads at the top, and out of four I’ve collected, only one was crackless and held butane. And I use it regularly.
Even the brand new one I bought was cracked in the package.
The knife itself is a Wenger handyman clone. It’s actually made with Wenger tools, but finished and assembled in China. Quality is 95% of Wenger. There is a Coast branded model, shown in my pic, as well as a gray Eddie Bauer model, which leaves out the saw layer, but has thicker scales with a rubberized insert. Both versions have victorinox style tweezers.
Charles

-
@ChopperCharles said:
Coast did that with a Wenger clone. It didn’t look bad and it works great, even 30 years later.... if you can find one without a cracked reservoir. The nylon was thin around the threads at the top, and out of four I’ve collected, only one was crackless and held butane. And I use it regularly.Even the brand new one I bought was cracked in the package.
The knife itself is a Wenger handyman clone. It’s actually made with Wenger tools, but finished and assembled in China. Quality is 95% of Wenger. There is a Coast branded model, shown in my pic, as well as a gray Eddie Bauer model, which leaves out the saw layer, but has thicker scales with a rubberized insert. Both versions have victorinox style tweezers.
Charles
Very interesting thanks for sharing.
-
KOWELL made an SD sized version as well. It ends up being more of a mini champ size with the scale. The older version without the manual gas switch is decent quality. The later models with the switch I’ve had to disassemble and modify to get to work properly.
Can’t post a pic (or save it) from eBay using my phone, so here’s the link to one: https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F233272388872
Charles.
-
@ChopperCharles said:
Coast did that with a Wenger clone. It didn’t look bad and it works great, even 30 years later.... if you can find one without a cracked reservoir. The nylon was thin around the threads at the top, and out of four I’ve collected, only one was crackless and held butane. And I use it regularly.Even the brand new one I bought was cracked in the package.
The knife itself is a Wenger handyman clone. It’s actually made with Wenger tools, but finished and assembled in China. Quality is 95% of Wenger. There is a Coast branded model, shown in my pic, as well as a gray Eddie Bauer model, which leaves out the saw layer, but has thicker scales with a rubberized insert. Both versions have victorinox style tweezers.
Charles
Wow Charles - great info

But I’m worried you need help with your pyromaniac tendencies...that trail of fire in the background looks dangerous! ???
-
This is the Eddie Bauer version.
It’s still made by coast and has the same high quality tools. The front scale is attached by rivets, so an evolution scale will press right on. The coast branded version uses the older Wenger attachment style for the front scale.
The lighter scale is attached to a drilled and tapped liner with screws.
These have two unique tools. The nail file tool is similar to the Wenger tool, but instead of coming to a tip it has a small flat screwdriver blade on the end. It also sits higher in the knife for easy extraction with the lighter scale in the way.
The blade is a Swissbuck style clip point blade, but only sharpened on one side, and it’s a combo blade with very small serrations near the tang.
Wish I had my knives here so I could take pics, but I’m at the hospital waiting for my mom to get out of knee surgery.
Charles.
-
Oh yeah the Eddie Bauer version has a titanium coated blade. Here’s a screen shot from my phone of the Eddie Bauer version.
Charles.

-
@ChopperCharles said:
I’m at the hospital waiting for my mom to get out of knee surgery.Charles.
Oh no! Is she ok? I hope it wasn't an accident or anything (not that it makes knee surgery less of a worry).
-
@Max Stone said:
I think it would be more fun to build a peanut-style lighter using your tray as a base?I have one of those peanut lighters, works quite well and holds fluid well(O-ring seal). Rides in the back pocket with the Vagabond. Don’t hardly know it’s there. I think it came from County Comm but not sure.


-
No it wasn’t an accident. She’s been putting it off for years because she is afraid of hospitals. But it’s gotten so bad and her mobility so poor that she finally got fed up.
She is out of surgery now. I’m still waiting for them to finish Whatever they’re doing and let me in to see her. Surgeon said it was the most complicated knee surgery he’s ever done. It took over 4 hours.
Charles.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

