general cleaning
-
i thought that was so simple :P
:Dwell u can go back to stone age and use toothpicks,plastic and brass brushes,and cleaners and light oil.theres nothing wrong with that :D
i do it too.
-
Toss it in the dishwasher from time to time- that's what I do!
Def
-
that works? im just worried about rust.
-
Victorinox actually recommend putting the Swisstool in the dishwasher :)
-
wow awesome, will do!
-
Yeah, that's the beauty of Vic products!
-
I receiver a MT that needed some cleaning yesterday so off into the ultrasonic cleaner with a mixture of 50/50 Lysol cleaner and water for 20 minutes. Needless to say ALL the dirt and grime came off without any problems, Once our of the bath a scrub with spray cleaner and a old parts brush, then a clear water rinse and a good blast from the air compressor. The MT then took a bath with the dinner dishes in the dishwasher and nor looks good enough to carry. A little jewelers rough with the Dremel buffer this AM will remove some of the surface scratches on the scales and implements. Then a quick ride on the Spyderco SharpMaker and it's ready to go. Will post pictures when I get it done.
-
@eodtech said:
I receiver a MT that needed some cleaning yesterday so off into the ultrasonic cleaner with a mixture of 50/50 Lysol cleaner and water for 20 minutes. Needless to say ALL the dirt and grime came off without any problems, Once our of the bath a scrub with spray cleaner and a old parts brush, then a clear water rinse and a good blast from the air compressor. The MT then took a bath with the dinner dishes in the dishwasher and nor looks good enough to carry. A little jewelers rough with the Dremel buffer this AM will remove some of the surface scratches on the scales and implements. Then a quick ride on the Spyderco SharpMaker and it's ready to go. Will post pictures when I get it done.Am I crazy when I say: That sounds relaxing. I have always found cleaning a tool or gun relaxing.
Be sure to post some pics EODtech. It sounds like you did a good job
-
I receiver a MT that needed some cleaning yesterday so off into the ultrasonic cleaner with a mixture of 50/50 Lysol cleaner and water for 20 minutes. Needless to say ALL the dirt and grime came off without any problems, Once our of the bath a scrub with spray cleaner and a old parts brush, then a clear water rinse and a good blast from the air compressor. The MT then took a bath with the dinner dishes in the dishwasher and nor looks good enough to carry. A little jewelers rough with the Dremel buffer this AM will remove some of the surface scratches on the scales and implements. Then a quick ride on the Spyderco SharpMaker and it's ready to go. Will post pictures when I get it done.
Am I crazy when I say: That sounds relaxing. I have always found cleaning a tool or gun relaxing.
Be sure to post some pics EODtech. It sounds like you did a good job
youre not the only one then buddy ;)
-
@eodtech said:
I receiver a MT that needed some cleaning yesterday so off into the ultrasonic cleaner with a mixture of 50/50 Lysol cleaner and water for 20 minutes. Needless to say ALL the dirt and grime came off without any problems, Once our of the bath a scrub with spray cleaner and a old parts brush, then a clear water rinse and a good blast from the air compressor. The MT then took a bath with the dinner dishes in the dishwasher and nor looks good enough to carry. A little jewelers rough with the Dremel buffer this AM will remove some of the surface scratches on the scales and implements. Then a quick ride on the Spyderco SharpMaker and it's ready to go. Will post pictures when I get it done.Well this AM I sold my "small" jewelry ultrasonic cleaner on another forum. The UC was just to small to fit the entire MT onto, it had to be put in at different ways / angles to get it cleaned up. I am now looking at a larger ( tub / basin ) size on so I can put a complete knife, MT, etc in to the tub.
Does anyone have ant recommendations as to manufacturer, how they are rated, what is the deciding factor in how well they clean - what measure do they use to compare the strength of the unit?
-

This is on the short list for my new UC .
I'll wait until they go on sale ( 20% OFF ) and use my 15% off coupon AND stack them for a multiple consumer discount - good size tank for MT's, knives, tools and implements.
A UC certainly saves a lot of elbow scrubbing and makes the cleaning phase of restoring a real breeze.
I neglected to take before and after photos of the last MT to hit the pool ( the SOG PPP pictured below in my signature block ), but will do some photos of the next MT to go into the NEW tank in a couple days - a used SOG ParaTool I just received that is ready to go for a swim!
-
I use what I have and this is what I do. Wash in as hot of water as I can stand with some liquid dish washing detergent. Open and close all the tools and all that until I stop seeing too much crud coming out, then rinse thoroughly. Then, I go hit it with WD-40 to get into the nooks and crannies to displace the water and possibly even more gunk. Then, I hit it with my air compressor to get out as much of the WD-40 as I can and any other gunk as well. Wipe it all down really well. Then, ever so lightly oil the pivot points, wipe off the excess and go along my merry way.
Mike
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login