The Perfect Box.
-
Europallets are not square but 120x80cm. If you want stuff to also cram nicely into an international container that has to be reduced to about 117x77 or so. (Working height inside a normal height container is about 235-238cm - better check that, it is from my leaky memory!).
I get the logic that a box first mission is to fit its content. However that also includes scenarios where the content is many small things, and for that one has a lot of freedom over the box size and design.
I don't think the best design for a one off box to be handled manually will match a tight pallet fitting one. The pallets wish introduces a non-ergonomic limitation, and then you have yet another balance and compromise to be made.
-
The only Right or Wrong is whether the box works for the Load,right?
It sounds like you are trying to design something pretty too?So if building for that rough size and pallet transport I would build more like a crate than a box myself.
It seems clear that you want something too big for a 1 person carry and I would make sure then that it has wheels and much better handles and also reinforced edges all the way around as well.
I would also build in some form of indexing to enable safer stacking so that the boxes interlock to some degree when stacked.
I would reinforce the edges so that the screws can bite not only onto the plywood endgrain but also to actual wood for strength.
If this is not what you want then look to inside cleats maybe so that you can get additional fastener strength?
By using 1x3 for example on each edge you can also easily build in the tops and bottoms to lock together when stacked and you might even need forklift guides of enough lift under the box for forks depending on the weight and how you intend to get these loaded in the first place?I probably also build a sealed box and then cut the lid from around the circumference of the box so that the lid is not just a flat piece but instead another structure that will resist bowing and flexing better.
I have had crates like this just "Explode" sort of when dropped too hard and depending on the contents that mat be more frequent than you might think but is never a welcome event.
@Sea Monster said:
I forgot to measure it, but this is one of the sort of thing I am talking about - simple box thrown together with offcuts of plywood and some screws. (in rough numbers, it'd be around 900x400x300)I don't recall what this one was originally for, and now it sits empty. Most (actually I think all) of it's brothers and sisters have been repurposed into garden boxes.
Right or Wrong - I believe these are proportions I find appealing - wider than it is deep, and about twice as long as it is wide.
I am interested in what someone said about pallets - a pallet is approx 1100 square, so if I made the boxes (say) 700 x 400mm, they would stack nicely in a pattern....
if I use 1100 as an upper limit for L + W, and maybe work the golden ratio into it (which I did spend some time with a pad and pen trying different sizes), perhaps I can find the Correct Dimensions.
I wonder what happens if I make a Box Z Deep, Z1.61 Wide and Z1.61*1.61 long.... (if Z is 260, then this will also meet the first criteria)
Will the universe survive such a thing?
-
The pallet constraint was just a thing of interest, I'm not terribly likely to need to stack on a pallet in this instance, and as pictured, I like to put handles on the boxes so meshing them together is not really going to work anyway.
The only Right or Wrong is whether the box works for the Load,right?
It sounds like you are trying to design something pretty too?So if building for that rough size and pallet transport I would build more like a crate than a box myself.
It seems clear that you want something too big for a 1 person carry and I would make sure then that it has wheels and much better handles and also reinforced edges all the way around as well.
I would also build in some form of indexing to enable safer stacking so that the boxes interlock to some degree when stacked.
I would reinforce the edges so that the screws can bite not only onto the plywood endgrain but also to actual wood for strength.
If this is not what you want then look to inside cleats maybe so that you can get additional fastener strength?
By using 1x3 for example on each edge you can also easily build in the tops and bottoms to lock together when stacked and you might even need forklift guides of enough lift under the box for forks depending on the weight and how you intend to get these loaded in the first place?I probably also build a sealed box and then cut the lid from around the circumference of the box so that the lid is not just a flat piece but instead another structure that will resist bowing and flexing better.
I have had crates like this just "Explode" sort of when dropped too hard and depending on the contents that mat be more frequent than you might think but is never a welcome event.
I am shooting for the "upper limit of one person lift/carry".
So far I've been putting them together with construction adhesive (sikaflex) and washer head screws, and I have not been able to break them if I tried.
I have put skids on larger boxes in the past - which would allow MHE use, but mostly to avoid having a giant moisture trap. These ones should not be so large.
Though a simple hinged flat lid is by far the easiest, it's not a massive step out of my way to do something like https://cdn11.bigcommerce.com/s-80qxgw/images/stencil/1280x1280/products/101/1902/Wooden-BoxLarge-Flat-TopHinged-Lid-Baltic-6-5__04274.1494402899.jpg?c=2&imbypass=on
which would give it some rigidity.
I can also put an internal frame in, in the event that the material itself doesn't provide enough strength and rigidity.
However, I am a habitual tightarse, and these things are always made of "scrap" ply that I have around, cut, glued, and screwed in an afternoon, painted whatever colour of weatherproof/exterior housepaint I have spare, and then I move on - So elegance of form is not a huge consideration, especially if it is going to include a tax of time and materials in order to achieve it.
-
Well now that you are cutting loose with more details I am beginning to understand what you want at least.
I like to use Pocket Screw Joinery lately and not use adhesive at all as I can then knock the box down if I need to later for any reason but the Sikaflex products are truly great for sure as adhesives go and should be pretty tough but maybe not as tough as the average person that might drop your box too?
I have seen things.
Pocket screws are crazy strong and all hidden and the joints are really tight too.
I don't know what could be easier than making a closed box and then sawing the top off a few inches from the intended top piece thus giving a three dimensional lid rather than a flat one but we each prefer what we [refer too.
I like a tip I learned from a friend and take all the random extra paint I have collected and just mix it together and then use a large knapp roller to paint the box,usually the color is some shade of grey to black and also usually pretty tough and covers well too.
If I need it to look good ad wear like iron I use a paint called Break Through here that is an Epoxy based paint that is truly amazing but it is pricey to be sure too.
I an not sure what the metal handles you showed and stacking the boxes have to do with each other really but I prefer a larger wooden handle that does not hurt my hand when lifting a heavy box and I can get a nice shoulder width grip on too.
Anyway there is no wrong way to make a box if you are happy with it in the end.
I too make most from whatever I have leftover but I also supplement this with new stuff if I need to.
These are some boxes that I have built a few times as anyone who sees them seems to want a set and they have been great in the shop and are easy to customize as needed too.
Rugged and light but the fronts drop open too as needed so they can be used while still stacked which is handy!
You can easily scale these to any size you want and also use sheet goods rather than 1x but this is what I had when I made these so......



@Sea Monster said:
The pallet constraint was just a thing of interest, I'm not terribly likely to need to stack on a pallet in this instance, and as pictured, I like to put handles on the boxes so meshing them together is not really going to work anyway.I am shooting for the "upper limit of one person lift/carry".
So far I've been putting them together with construction adhesive (sikaflex) and washer head screws, and I have not been able to break them if I tried.
I have put skids on larger boxes in the past - which would allow MHE use, but mostly to avoid having a giant moisture trap. These ones should not be so large.
Though a simple hinged flat lid is by far the easiest, it's not a massive step out of my way to do something like https://cdn11.bigcommerce.com/s-80qxgw/images/stencil/1280x1280/products/101/1902/Wooden-BoxLarge-Flat-TopHinged-Lid-Baltic-6-5__04274.1494402899.jpg?c=2&imbypass=on
which would give it some rigidity.
I can also put an internal frame in, in the event that the material itself doesn't provide enough strength and rigidity.
However, I am a habitual tightarse, and these things are always made of "scrap" ply that I have around, cut, glued, and screwed in an afternoon, painted whatever colour of weatherproof/exterior housepaint I have spare, and then I move on - So elegance of form is not a huge consideration, especially if it is going to include a tax of time and materials in order to achieve it.
-
Aye, I saw those pics previously when you put them in one of the toolbox threads.
Reminds me of and old army design - the only picture I can find - https://irestorestuff.com/vintage-army-box-transformed-into-industrial-side-table/
stackable crates that have the side open to reveal shelves.
-
Mrs slept in this morning, so I threw together the first box...
260x420x675
Depth feels good, width is okay, length is a possibly a bit much.
It looks nice, but when loaded might be a bit of a hand (arm?) full to manage.
It has nice principles - top and sides are (more or less) golden rectangles, and length + width = Pallet (1100x1100 for ISO containers, not Euro) so it would theoretically stack nicely for shipping.
but, it turns out that good principles on paper do not necessarily = good design or policy (who woulda thunk it? bureaucrats everywhere...)
As a bonus, due to whatever series of circumstances, I did not have my power saw or drill available, so I had to do the whole damn thing by hand.
Though I appreciate the fore-arm workout, I think I'll go pick up my things before doing the next ones.....
-
The first picture that comes to my mind is the traditional sailor's chest. A quick look at some auctions puts the sizes around:
L: 80-90 cm; W: 45-50 cm; D: 40 cm
Fairly close to some of your numbers in other words.They were made to be carried but probably by some fairly strong 19th century sailors, I wouldn't want to carry one any long distances but that goes for any bulky chest ones it starts filling up with stuff.
Another fairly common feature that might be a lot more intricate than what you're looking for is the slanting walls. It will make them more difficult to build but should in theory allow a larger chest to be carried more like a smaller one. Another benefit to the slanted design would be to make sure they would interlock when stacking them.For a more speSmurfpillsed chest this Swedish tool chest made its way around the internet a few years ago and I still like the design a lot, especially the doors in the lid and how they help keeping the chest open and the tools accessible.

For more pictures, visit the auction site: Bukowskis -
Now that is a box - fun one!

-
Double post. Don't know how to internet.
-
I ended up making another box, approx 10% shorter and narrower, same depth. It feels pretty good.
I also made a doghouse, because I got distracted.
If you're lucky, and I remember, you can have pics tomorrow ;)
Once I've met my current Box needs, the next project will be some bedroom drawers.
I mean sure, I could just buy something for less than the cost of dinner and a drink, but where's the fun in that?
Edit: I had a sailors/treasure/pirate chest a few years ago out of some decking timbers. It was insanely heavy
I'm pretty sure it was still in the old house when they knocked it down.
-
Do not imagine for even a moment that my deep and abiding interest in boxes has in any way diminished.
I was away for a coupla weeks for work, but now I'm back, and another three boxes have been cut and assembled...this time sized for efficiency out of a 4' x 8' sheet of plywood (so, 24" x 12" x 13")
Hopefully this'll mark the end of my box needs for the short term, and I can turn my will to the chest of drawers....
-
I'm a fan of plastic bins, preferably ones with lids that can stack.
I had one (lidless) for my chainsaw + accessories that is about 650mm long but found it uncomfortable carrying such a weight with my arms so wide apart. I eventually found a smaller one which is much better. I just measured it and it is only 50mm shorter, but what a difference that makes. I had to cut a slot in the end for the bar but I would have had to do that for the other bin if I was going to keep using it for that.
-
Oh Aye, the nigh-ubiquitous stack and nest is one of my favourites - http://www.viscount.com.au/products___services/materials_handling/crates/stakanesta_crates
Few establishments that have employed my consultation services have survived without incorporating them into their work systems in one way or another.
-
Hmmm
This troubled me too for years when I used to collect MTs & SAKs - now everything is just stored in large clear boxes and kept out of sight.However, with the passing of collecting came the urge to visit a previous hobby of mine - photography.
In the space of 3yrs I’ve swapped and changed from film to digital dslrs, got caught in the hype and moved onto mirrorless, realised my error and sold the lot and reverted back to dslrsToday with seven canon dslrs, over 20 canon lenses and seven Speedlites i need to ensure they are all kept in optimum conditions.
The dreaded fungus is a serious threat to lenses so storage had to ensure maximum prevention. Wood is fabulous for ensuring damp, steel for condensation which leaves plastic.I now have a set of the “Really Useful Box” these are available in sizes that can easily stack .
Now all my photo gear is kept in these clear boxes with jumbo satchels of silica gel. I simply take out what I need and return after use. No fabric or batteries are kept within. So far everything has remained pristine and hopefully should provide years of trouble free use.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login