Do your Leatherman bits do this?
-
@Walley said:
i have had this happen. infact, i took a look at the ones in my holder just now and every flat tip in there has a bend to it lol. I also had a phillips bit break too. it was the combo bit that came with the surge.
if you have never bent or broken a bit before, then you are not trying hard enough!If you frequently bend and break driver tips, you're trying too hard.
:D -
@Huntsman said:
I had this happen on the large driver on my Supertool - Which was very surprising/disappointing :( - As that guy is meant to be the beefy tool
Especially as I was not applying massive force!Will try and snap a pic later.
The large driver on my Surge chipped once. Had to grind down and reprofile the tip. Rare to see that happen though. :ahhh
Never had a large dedicated driver bend, but a lot of my user tools have twisted small flat drivers(rebar, mp, mp600, swisstool, spirit, toughtool, free p3, bear grylls, bear mfg, and some others).
The bit kit bits get a harder workout than those drivers, so maybe LM had a defective batch of bit kits at one time? -
Here is the only set I have used since beginning to carry it. They ever work great in the Crunch. :)
Looks like the T6 needs to be ground down to a fresh tip though. :ahhh


-
I am usually pretty good with my drivers. But, the small slotted driver on my Micras usually ends up a little twisted and the smallest torx bits in my bit kit have also gotten twisted. I do think the LM bits are significantly softer than the dedicated drivers and bits I have. I got both the LM bit driver and the bit kit, but I only carry one card so I cherry-picked the bits I carry thus leaving out the slotted bits so I have never used them. The on-board drivers for my ST300 are pretty mint save a couple scratches even after I use them hard. I think this means I dont abuse my tool and I dont feel out of place saying LM bits are not very good quality. The only reasons I carry them are: I already bought them and I would like my money's worth out of them. The shape means I can almost carry 2 for the space of one real 1/4" bit. There is still enough non-mangled ones left to provide utility. And finally, I'm not sure if a strip of actual 1/4" bits would fit in the slot in my Skinth (which I will Not be giving up as far as I can see). It won't be too long before I simply must find out, in the mean time I'll make do with what I got. I mean, that's what we do here isn't it?
-
Hi, guys
I believe I've seen a similar discussion somewhere a while ago and anyway most of the participants noted they have a more or less asymmetrical flat bits. So is the one that came with my new Signal - never used before, almost brand new, didn't see any hard work yet, however it's noticeably off center as well - just like the one on my Wave and all other flats in the bit kit... Don't know why, but I believe they were manufactured that way...
-
FYI for anyone with a bench grinder, you can easily grind down the sides of any standard bits to make them fit in your MT.
-
Only thing about grinding is it ends up annealing the metal. Either you will need to reharden the ground bits, or use them gently. :ahhh
-
the bits that i ground down were 2" and 6" long impact bits. they retain the hardness on the tip, they just dont fit in the sheath holder very well. :D
you could also avoid annealing by rigging up a water tray under your grinding wheel.
where there is a will, there is a way!
-
Easy peasy, lemon squeezy.

-
@gerleatherberman said:
Looks like the T6 needs to be ground down to a fresh tip though. :ahhhThat's a good idea! I'm on the 2nd T6 I've had this happen to. Last time leatherman sent me 2 new ones. Holding out on using my last new one.
-
@Amallott said:
That's a good idea! I'm on the 2nd T6 I've had this happen to. Last time leatherman sent me 2 new ones. Holding out on using my last new one.
Work like a champ. I've used a coarse stone to fix T6/T8 bits before. They usually have three good tips by grinding to a fresh one before the taper.

-
I may also get to freshen up a couple mine as well
great tip for those tips :D 
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login