Gerber Mp600 owners club ;)
-
Thanks guys. Someone here going for an ST on the bay?
If so, I’ll drop out. Don’t think it should go for what it’s up to. -
My Gerber Black Oxide Duo.

-
What does everyone use to take their 600s apart to mod? I will have some on the way and want to swap some of the tools.
-
There are out there the loki wrenches (from member lokimobile); I made this from a cheap bit set: a 1cm/3/8" bit which I reprofiled the tip to fit two opposing notches from the pivot bolt (found on the metric and the imperial rulers). Remember to heat the pivot to loosen the thread lock ("Loktite").You do not need a second bit, as the female end of the pivot fits inside notches in the handles and won't turn. I place a drop of blue Locktite on the bolt's threads for reassembly; blue holds fine, and you don't need to heat it up to break it free. Simple and pretty effective. Good luck with your moddin' and hope to see pictures soon!
Edit- Another tidbit of info.: be careful of the position of the indexed washers ( the ones that go between tools to prevent clumping); I tend to push out the female end of the pivot with a piece of wire ( once the bolt's off) so that I can keep everything in order while disassembling and mod/ reassembly. Hope it makes sense, and helps!



-
@Juan el Boricua said:
My Gerber Black Oxide Duo.Nice setup!

@Juan el Boricua said:
There are out there the loki wrenches (from member lokimobile); I made this from a cheap bit set: a 1cm/3/8" bit which I reprofiled the tip to fit two opposing notches from the pivot bolt (found on the metric and the imperial rulers). Remember to heat the pivot to loosen the thread lock ("Loktite").You do not need a second bit, as the female end of the pivot fits inside notches in the handles and won't turn. I place a drop of blue Locktite on the bolt's threads for reassembly; blue holds fine, and you don't need to heat it up to break it free. Simple and pretty effective. Good luck with your moddin' and hope to see pictures soon!Good idea there, Juan!

-
Thanks, gerleatherberman!

-
Thanks Juan! I think I’ll attempt to make my own too. Just won an ST, so I have the philips that I wanted.

-
Thanks GLB! Now the wait. I’ve never seen the sight tool in person. It appears to be thick. Can more than one tool go in its place?
-
Never mind. Just got a close up of the pivot. :)
-
My helper @ work. :D
Edit: Forgot picture...

-
Received the Leatherman XL sheath Saturday. I love everything about it, but the long pull. That Velcro makes a ridiculous amount of noise.

-
Good fit, with pocket for bit kit, and elastic band for light/marker!! Nice pairing, Roc.

-

It reminds me of my Maxped single sheath when new; sounded as if my trousers were ripping!

-
My haul. Not sure what I want to make yet. The thickness of the ST’s philips and sight tool has me guessing.

-
Nice trio, Roc.


-
Thanks Juan! I haven’t had to use the wire cutters yet, but wanted an infused wire cutter head just in case the replaceable cutters suck. I also prefer the blade from that one. If I do start swapping tools it will have to go into the ST. That long philips is a must. Not sure what could replace the sight tool though. Open to suggestions from anyone who has been here before. :)
-
Don't worry much about the cutters, unless you plan to use them as your primary cutters (which I wouldn't recommend), or back ups (which I wouldn't recommend either!); mines have been fine for copper wires (electronics, house wiring, both single and multistranded), and steel wires for up to cloth hanger; for cloth wire, I notch it with the cutters and then use the pliers to "bend-cut it" . Not a single nick or shattered cutter. Mind you that I may use them once or twice weekly. If you're mindful of what they were adapted for, you'll enjoy them for long.
Having said that, until Gerber makes replacement cutters out of tool steel or 154cm SS, my integral cutters will be the best of Gerber's.
Roc, how about exchanging the sight tool for a saw blade exchanger? Or scissors and an awl? Or ...I'll let others chime in now.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
