Bolsters advice
-
I want one of each!

-
Might have to make another at some point then :P, Im out of horn tho so lets try ebony next :o
-
Just finished up my bolstered SAK mod, you can check it out on my thread /topic/82530
Two of my bolsters broke off, one glued and one soldered, while I was assembling the knife however the pinning is holding everything together perfectly due to tight tolerances in the brass and horn. Also Drilling the tops of the holes out to 2mm worked perfectly with the 1.6mm brass rods
-
Hi, guys. I'm jumping in here a little late but for what it's worth...
I've gone through a similar barrier with SAKS and a love for pocket knives in general that leads me to the more traditional methods of building "folders". The next logical step has been bolsters.
I've had good luck with silver solder and good FLUX which I think is the key, here. The solder flows at a really low temp and slides in right under the bolster which is lightly clamped to the brass liner. Am using nickle silver for that process. I got a kit from Amazon with the solder and the flux.My son has a machine shop/welding business and knows all the fab. guys in the area. One of his suppliers has a water-jet business and he cut me some excellent SAK liners out of .040 brass sheet. A 12"X12" sheet was about $75 to do and it yielded lots of perfectly cut 91 & 84mm liners. (Don't remember how many but the whole sheet was used with little waste..maybe 20 of each size) The trick is, give him the aluminum ones to copy. Not perfectly smooth and you still gotta drill the holes but it's so nice to have a pile of precut brass liners to work with.
Another cool machine shop trick is to make integrated bolsters with liners out of brass or aluminum stock. This uses, for example, a 3/16" thick strip of brass, 1" wide, 4" long. Plenty big for a single SAK scale. An easy process for a milling machine is to start 1/2" in from the end and cut out a section of the strip 1/8" deep, 2.5" long, and the full width. You end up with a piece with a plateau, a long cutout valley, and another plateau. Scale material goes into the valley and the plateaus become the bolsters when rounded over. Look at the side of a Buck knife to see what I mean. Same technique. Pix show examples of soldered and integrated bolsters. I will try to do a JPG of this kind of thing. It's pretty easy and pretty cheap to do.
For the pins I use brass and always do a tiny little countersink using a Dremmel bit spun in my fingers. This is a many sided V type bit that I use gently to get just the smallest penetration. Like, maybe 10-20% of the way through the scale. Then if you're using domed pins or flush ones (sanded smooth) you still have that mechanical lock-down of the swollen pin head in the hole.
Pix below - All are 84mm SAKS
first is a soldered nickle silver bolster
second is integral aluminum bolster (double ended)
third is integral brass bolster (double ended)Cheers



-
@Jspiggle said:
Ive been working on some bolstered 58mm scales. Just used regular plumbing solder to solder the bolsters to the brass liners but one fell off as I was filing so I superglued it back temporarily and it seemed to hold up just as well as the solder did to the shaping =O!!Knowing that Im going to pin through the bolsters anyway I was planning on leaving that one bolster glued and relying mostly on the pins. Also planning on opening the very top of the 1.6mm holes up to 2mm and sanding the pins flush afterwards so I will let you know how that goes.
Right now though I cant decide if I want to put a bolster groove in or not so its just going to sit on my desk for a while unless some of you can help me decide. Yea or nay to the bolster groove?

Gotta say those ringed bolsters look mighty nice.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login