Day by Day...a Journey down the 91mm Range
-
Day 7
So far we have covered Vic’s scissors and wood saw as the central tool options in the 3-layer 91mm lineup. Both excellent tools, driving good demand for their respective owners, the Climber and Camper.
But there’s another tool that gets a lot of interest from SAK users; the inline Phillips screwdriver. And this tool gets our attention today, as we’re covering the Spartan Lite.
Bit first, as the name implies, we have to deal with a rather questionable feature. Victorinox introduced a small LED flashlight into their 91mm lineup some years ago. Running on two button cells, the output is hardly stellar, and while it has become brighter in recent years as LED technology improves, it’s never going to be more than a few lumens...enough to help you find a keyhole on the dark, or help you avoid tripping on a dark stairway.
I use my mobile phone as a flashlight when needed, or I carry a small AA Fenix if I know I may need one ahead of time. So for me, having a tiny LED on a SAK is largely a waste of time, especially as it means you cannot deep rinse the SAK for cleaning, and you can’t remove the LED if you want to illuminate what you’re trying to use the SAK for in the dark, the very time you would need a low-output flashlight! There’s a 6-layer exception, but that’s for another day. But for the rest of the ‘Lite’-equipped SAKs, the LED is a non-feature in my book.
So with that out the way...let’s return to the tool tethered to the opposite pivot; the inline Phillips. And as bad as the LED is as a flashlight, the Phillips is at the opposite end of the spectrum, because it’s really good!
Unlike the ergonomically-challenging Phillips found as a back tool (like on the Tinkers), the inline Phillips snaps out to become a pointy one inch extension of the SAK, with a good-sized cross-head and strong (4mm) tool thickness. It even has a 90 degree detent, for increased torque or for difficult-to-reach spots. As an extra bonus, the inline Phillips is perfectly central in this 3-layer SAK, making it super-easy to rotate in your hand (did I hear someone say Yeoman mod?)
Actually, the inline Phillips is such an A+ tool, you can overlook the F- tool its paired with on the Spartan Lite. Sadly, with the extra cost and questionable LED, the Spartan Lite often gets overlooked. Even if they sex-it-up with a mini screwdriver accessory and transparent scales.
Of all the paired tools in a SAK layer, the inline Phillips and LED probably top the list for ‘best and worst’ implementation of a dedicated, stand-alone tool.
But when all is said and done, the Spartan Lite still has a great base toolset and an excellent inline Phillips, so it’s still a great SAK for pocket carry. Maybe switching the button cells for some headache pills would be more useful, especially if you bump your head on the dark.
Pros:
- Excellent inline Phillips driver
- Still a Spartan under the skin
Cons:
- LED all but useless and cannot be removed
- Expensive Spartan upgrade
Bottom line:
Much overlooked, the Spartan Lite has the best implementation of an inline Phillips on any current 91m SAK, but made almost completely redundant by the 4-layer Explorer that ditches the useless LED for the (slightly more useful) magnifier, while adding scissors.



-
Huge fan of the inline driver
. It actually seems a lot stronger than the one on the Spirit? Meaning my Spirits driver is really starting to show wear while my Explorer is barely sweating
.It would be neat to see a total redesign of the LED enclosure. There is an terrific mod here on MTo somewhere on the scale LED. Anyways, nice carry today.
-
The inline Phillips is a nice additional tool to have on the SAK’s. I like mine!
-
Bonus shot...the LED in use. Oh, and the button has two positions, instantaneous and latching. Which could make this SAK useful as an unattended beacon for a military deployment...or maybe not.


-
Another enjoyable read Max.
I like the inline Phillips too.
I have had a couple of customs made and I usually have that tool included if possible. It's always opposite a magnifier though.I do think the newer LEDs are brighter. I have an Expedition kit with an inline LED and it's much stronger than one of my older SAKs, even when the older one has fresh batteries.
-
Oh my goodness Max
Day 7 tells me you don't love awl things Vic :o
-
Max... Well done! Are you a writer in your other life? I look forward to reading your mini reviews each day!

-
Another great write up, looking forward to tomorrow

-
as am I 
-
Thanks VICMAN, jph_777, Greg, Rapidray

Kind of a rant today...but thanks for all the feedback

No, writing’s not my strongpoint. I just think I’ve read too many reviews in my life...
-
I used to have a Spartan Lite, but it's in pieces now
Some tools made it's way to my mod though 
Great quick reviews Max!
Sent fra min FRD-L09 via Tapatalk
-
Thanks RF52.

-
Great write-up. I too love the inline phillips, but strongly prefer the other pairing of the magnifying glass, which I also like.
-
Thanks Sos.

Yes the inline Phillips is one of the best SAK tools imoDay 8
The last 3-layer with corkscrew I’m reviewing is the Traveler. This is really just a Climber with a digital top scale.
As I reviewed the Climber a few days ago, I’ll focus on the digital side of this SAK. Grab a cup of coffee, there’s a bit of reading here...
Victorinox used to have two different digital scale options in the 91mm range; one for time functions (the Voyager), and one for atmospheric measurements (the Altimeter). Presumably Victorinox took the opportunity to combine both when they were forced to do a redesign, possibly due to an EOL component such as the LCD display. Today we are left with just the Traveler in the 3-layer range.
The digital scale uses a real-time clock, powered by a single button cell, to keep time. Functions include hour:min display, with PM icon or 24-hours...but no seconds.
It also has a single alarm function with a basic ‘beep...beep...beep’ sound that may (or may not) wake you up.
In keeping with all good digital timepieces, it also has a countdown timer that can be set to count down to a beep...beep alarm, from 9hrs 59min, and including seconds below 10 minutes.
And it also has a stopwatch that counts up in seconds, without any sub-second recording (sorry, no chance to do the Casio start/stop reflex test here...)
Timing functions run independently, so you can time your hard-boiled eggs while you check how long the toaster takes to pop.
Rather than spoil the sleek lines of the SAK with protruding buttons, Victorinox cleverly engineered the button into the shield on the scale. Yes...just one button.
Pressing and releasing it steps through the various functions, with a little icon on the top row indicating the mode you’re in. Round clock face, wind-up alarm clock, ding-dong bell and old-fashioned stopwatch.
Holding the button down in any of the time modes does two things. After 1 second, the back-light comes on for a few seconds (electroluminescent). Keeping the button pressed for a further second will cause it to beep once and enter the setting mode, or starting the stopwatch if in that mode.
Now the fun starts! As there is only one button, the display shows a little up arrow, allowing you to advance the time (for the clock, alarm or timer), either by press/release (single step), or by holding in (fast and after a few second, faster). If you pause and release for 2-3 seconds, the arrow automatically changes to point down, and now you can press the button to step the values backwards. If you do nothing, you get another chance (2-3 seconds later) to increase again as the arrow switches to up, and one final time down again. If you wait for the arrow to cycle up/down, you can press and adjust the time up and down indefinitely (or until the novelty wears off). Once you’re satisfied (if not a bit confused), you simply wait the 2-3 seconds without pressing the button, and the value is set. Confusingly simple.
Starting/stopping the stopwatch is a similar press-and-wait affair. The stopwatch will run 2 seconds behind the event you are timing due to the press/hold requirement, but the 2-second stop delay (also needs press/hold) means the timing will be accurate overall...somewhat clever.
Press/hold for a few more seconds resets the stopwatch.Using just one button for all this functionality is quite challenging, and can test your patience. But with a little muscle-memory and practice, it begins to make sense.
Independent to the time-keeping circuitry, the digital scale also includes an atmospheric pressure/temperature sensor. This is utilized to calculate the estimated altitude (selectable in m or ft), barometric trend (weather forecast) and temperature (selectable in C or F).
Pressing the single button cycles through these three functions, but mixed in-between the timing functions. For some reason, Victorinox chose to have the order Time/Altitude/Baro trend/Alarm/Timer/Stopwatch/Temperature. A little triangular Matterhorn mounting icon for altitude, the word ‘baro’ for the weather trend, and no icon for temp, as I guess the degree C or F gives it away.
Press/hold in these modes also allows setting. In the altitude mode you can set the altitude to a known reference and tell the system what algorithm to use to calculate the altitude based on the measured pressure and temperature (standard, hot or cold climate). You can reset the barometric trend graph and adjust all the units when in the temperature mode.
The circuitry is fairly basic compared to some sensor-equipped watches. You cannot tell the system if you are stationary (so that pressure changes are interpreted as weather-related), so the barometric trend graph is only accurate if your altitude is relatively constant over a few hours. This also means that the altitude value will drift at one location as pressure varies due to weather.
But the sensor is extremely accurate at measuring pressure, and when calibrated (against a GPS altitude), it gives accurate readings. Just climbing one flight or stairs will show a change, and the readings across 2 devices are never more than a couple of meters apart.
The temperature needs a good half-hour to adjust from pocket to ambient (similar issue with watch-based sensors), but is also accurate to within a couple of degrees when compared to other sensors that I have.
Overall, the seven modes are quite useful and not too gimmicky. If I had the chance to suggest improvements, I’d change the bell icon to an hourglass as it’s easy to confuse the bell (timer) with the alarm clock. I’d also add the option for a hourly beep as this hardly uses any power, but is a nice reminder as time goes by. I’d also add a light sensor so that the press/hold does not activate the backlighting and drain the battery, unless it’s dark. But these are small gripes and don’t detract from the usefulness of this device.
While I’ve been tempted to pop off the digital scale (it appears to attach the conventional way), there are no tool recesses (tweezers, etc), so I’d likely damage the scales’s plastic edge or twist the circuitry which would not be good. Fortunately, the scale is transparent, although frosted, so some of the electronics are visible for the curious onlooker.
The LCD display has a really tough plastic window overlay, clearly beefed-up to prevent damage for knocks and drops. It’s also slightly recessed, reducing scratches when the SAK slides around on its top scale. The digital scale is a couple mm thicker than a normal scale, but it’s hardly noticeable and in this Climber version, does not affect its carry-ability.
With some design genius, Victorinox managed to squeeze all four Plus tools on the non-digital scale by using slightly shorter tweezers that are stored in a slot on the opposite side to the pen and toothpick. Vic also include the pin and mini-screwdriver with the digital Climber (sorry, Traveler).
One consideration is that you can never let the Traveler get wet. The electronics and battery compartment are not sealed so it could be easily damaged by water ingress if dropped in a puddle. This also means that the standard soak/rinse cleaning method is a no-no. As a side note, water generally damages low-voltage electronics not from short-circuits, but from electrolysis corrosion. Equipment can be saved if you remove the battery immediately on water contact, and dry the circuitry fully. Something worth remembering if you accidentally dunk your Traveler.
Pros:
- Fun digital features that actually work
- Digital scale is built to be tough
- Climber tool set always a winner
Cons:
- Single button interface can be frustrating
- Not sealed against water
- Very expensive for what it is
Bottom line:
While there’s really no need to have a digital timepiece with atmospheric sensors on your SAK, it’s a fun addition that adds to the already excellent “fiddle” quality of any SAK. Makes a great gift or as an emergency egg timer.



-
Another great read Max!

I'm a fan of the digital scales. I went camping and the first night my iWatch ran out of battery, no problem, my iPhone still had juice, but it was running low, it was then that I realized how nice it was to have something that didn't need plugged in each night to tell me the time. -
Thanks FB. You make a good point. I actually don’t know how long the battery will last. I think the electroluminescent backlighting will shorten it significantly, but I’d expect maybe 12 months normal use, similar to a sensor-equipped non-solar Casio.
-
. Nice write up. Lots of great info on that SAK.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

yep, the LED is probably the most pointless tool developed by Victorinox, but I still love them awl (like children :D )