Mini Ratchet Chatter
-
@cody6268 said:
Wondering how the quality is. Here in the US, a similar model is sold by Stanley Tools as Craftsman. My first broke on a light duty task, the second often has some problems. I'm guessing either who is making that model for Menard's and Stanley either ripped off or makes the Bosch.the bosch set seems to be decent quality.
i'll put it to some heavier use in the shop,and decide.
probably will get the Vic ratchet set as well,since its available here as well.
apart from these 2,i have not come across compact pocket size ratchets here. -
@Mechanickal said:
I can confirm the butter blade is a good one.It's strange looking but cuts through zip ties, insulation, drywall and plastic tubes like a hot knife through butter...

Yeah, one also cut most of the way through my thumb once so I can testify to the cutting ability of these!
I was of course working in a stupid and unsafe way at the time (up a stepladder, trying to open the battery casing on a smoke detector that was dangling from the ceiling cavity by its wiring...the ladder wasn't really tall enough so I was working above my head...some fool had epoxy glued something onto the body of the alarm that obstructed the battery hatch and I was trying to cut it off whilst holding the thing with my other hand). So I got what I deserved, really.
-
Any fans of the Teng Tools 1400B? Great little tool!

These are 90mm long and really handy for tight spaces. There have been (at least) two variants, the newer one (at the front of the picture) is the same length but slightly thicker and heavier with a bigger 'head'. I guess this makes it more robust, but I'm not sure it's an improvement as the smallness and lightness of the original was a feature and it was certainly robust enough for anything you would likely want to use it for. But it's only a small change and the new model remains extremely handy.
I got the earlier one as part of this kit:

which is pocketable and allows you to do a lot (you can just see there is a 50mm bit extension sitting underneath the ratchet). You can also see above that I've added to the basic kit by putting four low-profile hex bits inside the four largest sockets. With these bits inserted directly into the ratchet I can get into a space with about 21mm clearance.
-
Yeah, I know :'(
Bit of an exaggeration to say it went most of the way through my thumb, but I very nearly went to hospital with it.
On the plus side, I didn't fall off the ladder which is a bit of a miracle

-
@fullbreakfast said:
Any fans of the Teng Tools 1400B? Great little tool!
These are 90mm long and really handy for tight spaces. There have been (at least) two variants, the newer one (at the front of the picture) is the same length but slightly thicker and heavier with a bigger 'head'. I guess this makes it more robust, but I'm not sure it's an improvement as the smallness and lightness of the original was a feature and it was certainly robust enough for anything you would likely want to use it for. But it's only a small change and the new model remains extremely handy.
I got the earlier one as part of this kit:

which is pocketable and allows you to do a lot (you can just see there is a 50mm bit extension sitting underneath the ratchet). You can also see above that I've added to the basic kit by putting four low-profile hex bits inside the four largest sockets. With these bits inserted directly into the ratchet I can get into a space with about 21mm clearance.
Here in the US, I think Craftsman and Menard's sell what is pretty much a knockoff of that design. The Craftsman ones (even AFTER Lowe's replaced it on warranty) break easily. I like how they're reversible and take standard 1/4 bits (both the Chapman and Kobalt Chapman knockoff I have require special bits with ball bearing detents on them), so I might be getting one of those myself.
-
@cody6268 said:
Here in the US, I think Craftsman and Menard's sell what is pretty much a knockoff of that design. The Craftsman ones (even AFTER Lowe's replaced it on warranty) break easily. I like how they're reversible and take standard 1/4 bits (both the Chapman and Kobalt Chapman knockoff I have require special bits with ball bearing detents on them), so I might be getting one of those myself.I think if you get the Teng set (or the ratchet by itself) you'll find the ratchet is pretty durable and won't easily break on you. The bits are good too.
-
@fullbreakfast said:
Any fans of the Teng Tools 1400B? Great little tool!These are 90mm long and really handy for tight spaces. There have been (at least) two variants, the newer one (at the front of the picture) is the same length but slightly thicker and heavier with a bigger 'head'. I guess this makes it more robust, but I'm not sure it's an improvement as the smallness and lightness of the original was a feature and it was certainly robust enough for anything you would likely want to use it for. But it's only a small change and the new model remains extremely handy.
I got the earlier one as part of this kit:
which is pocketable and allows you to do a lot (you can just see there is a 50mm bit extension sitting underneath the ratchet). You can also see above that I've added to the basic kit by putting four low-profile hex bits inside the four largest sockets. With these bits inserted directly into the ratchet I can get into a space with about 21mm clearance.
That looks like a nice tool breakfast - runs just a little more expensive than the Topeak ratchet here in the UK.
Been using my Topeak a lot at work - great for dismantling barrel locks at work and getting in tight spaces. Also easily small enough to carry around and not have to go all the way back to the workshop for a driver all the time.
-
I couldn't see it on their site, but I'm fairly sure Teng Tools used to do a neat go-through socket.
Here's the same thing by another marque - https://www.youtube.com/watch?v=IBjGFB9gvqE
=
-
@Sea Monster said:
I couldn't see it on their site, but I'm fairly sure Teng Tools used to do a neat go-through socket.Here's the same thing by another marque - https://www.youtube.com/watch?v=IBjGFB9gvqE
=
You can buy the teng ones on amazon.
I have a full set of Halfords advanced go through ratchet spanners.
Solid ring spanner one end to break or to tighten were a lot of torque is required and the ratchet ring spanner the other end. -
@magentus said:
That looks like a nice tool breakfast - runs just a little more expensive than the Topeak ratchet here in the UK.
Been using my Topeak a lot at work - great for dismantling barrel locks at work and getting in tight spaces. Also easily small enough to carry around and not have to go all the way back to the workshop for a driver all the time.Nice portable kit you have there - a little adjustable wrench like that is a good thing to have handy - I just recently got an Irega one that looks a similar size, about four inches. Have not tried any Topeak tools yet but I see they get some good reports on here.
-
@fullbreakfast said:
Nice portable kit you have there - a little adjustable wrench like that is a good thing to have handy - I just recently got an Irega one that looks a similar size, about four inches. Have not tried any Topeak tools yet but I see they get some good reports on here.Can't fault the Topeak - tough as nails - the 1/4" bit holder is really handy (magnetized too) so you get double bubble for your cash
-
@magentus said:
Can't fault the Topeak - tough as nails - the 1/4" bit holder is really handy (magnetized too) so you get double bubble for your cashYeah, the Topeak is a really great little tool. Perfect for a light EDC toolkit (and I find myself going for it even at home at times). I have switched to the similar Victorinox ratchet but that's mostly do to how well it carries in the Spirit sheath. In general I think the Topeak version is the more user-friendly tool due to things like the direction switch and how the ratchet doesn't allow the bits to go right through.
-
@Fortytwo said:
Yeah, the Topeak is a really great little tool. Perfect for a light EDC toolkit (and I find myself going for it even at home at times). I have switched to the similar Victorinox ratchet but that's mostly do to how well it carries in the Spirit sheath. In general I think the Topeak version is the more user-friendly tool due to things like the direction switch and how the ratchet doesn't allow the bits to go right through.Yeah - not handled a Vic ratchet, but the Topeak is nigh on perfect as an easily carried EDC - that, and the Vic 'L' wrench with bit holder and the small adjustable spanner I carry covers an enormous range of tasks for hardly any weight or pocket space. Add the Spirit and I rarely have to grab anything else from the workshop aside from a drill saw or hammer.
It's a really well thought-out tool and super robust. -
I keep a topeak ratchet, leatherman extender and a leatherman card with the most used bits in my wallet. Have done for years as I bought a job lot of the same wallets off eBay several years ago, and found a few more recently and bought them too.


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
