Swisschamp owners club
-
Thought I'd add my new-to-me SwissChamp:

-
@FolderBeholder said:
Thought I'd add my new-to-me SwissChamp:

Nice!
-
Very nice Lisa!!
@Simon_Templar said:
Nice! -
Thank you ST, RR and Barry!

-
@FolderBeholder said:
Thought I'd add my new-to-me SwissChamp:

Love the scales........ And the SwissChamp, of course.
-
Are you wearing the matching t-shirt FB?
-
@FolderBeholder said:
Thought I'd add my new-to-me SwissChamp:

Aaaaaarrrrrggggghhh FB - You found my Holy Grail
- I so want those scales - after seeing them in the Wiki (Climber page) quite a while ago
I spent a few months looking out for them on ebay - But never any luck - If you do see another one could you snap it up for me please?
Interesting thoughts Steinar

- I so want those scales - after seeing them in the Wiki (Climber page) quite a while ago
-
@FolderBeholder said:
Thought I'd add my new-to-me SwissChamp:Very nice FB!

-
@Huntsman said:
Aaaaaarrrrrggggghhh FB - You found my Holy Grail- I so want those scales - after seeing them in the Wiki (Climber page) quite a while ago
I spent a few months looking out for them on ebay - But never any luck - If you do see another one could you snap it up for me please?
I'll notify you if I spot one Huntsman.
I actually only thought they came on the Climber knives.Thank you Vicman!

- I so want those scales - after seeing them in the Wiki (Climber page) quite a while ago
-
Nice one FB

-
@FolderBeholder said:
I don't have the matching t-shirt. Hope it's not a requirement to wear when carrying the SAK or else I'll have to go topless. :ahhh:ahhh
I don't have the t-shirt either, but I did find one at a pretty big discount. But it's a few sizes too small for me.
Maybe I'll buy it anyways
-
I don´t have the t-shirt either, but I had one, once. I wore it to tatters.
I also have a set of matching playing cards somewhere. -
I sold mine...

-
greetings, experts. I have a Swisschamp. The outer liner of my knife is bent.
- Because I love and appreciate this tool, do you know the right non-destructive way to fix this problem?
- Is there a possibility to repair without removing the scale?
The answer from you experts will be very appreciated. Sincerely Thanks

-
Hi abwaluyo
This is the layer next to the cap lifter/large flat driver.
Unfortunately there is no easy way to repair a bent liner at the pivot area.
Without the opportunity of inspecting the knife, it’s difficult to make an assessment.
You could try pressing the SAK together in a vice between layers of hardboard for protection. This may help press the liner flat without removing the scales. (Fold the CS out to prevent pressing it).
If this does not work, next would be more forceful work involving removing the scale and using a light hammer to remodel the liner. Obviously this and above techniques are not without risks (...no responsibility, etc, etc)
Final option is a rebuild. Either factory or modder.
Good luck!

-
@abwaluyo said:
greetings, experts. I have a Swisschamp. The outer liner of my knife is bent.- Because I love and appreciate this tool, do you know the right non-destructive way to fix this problem?
- Is there a possibility to repair without removing the scale?
The answer from you experts will be very appreciated. Sincerely Thanks
I'd try a C-clamp and use some of the suggestions above. I'd open the Caplifter/SD too, to press the bent liner against it.
If that doesn't work, you're probably best off sending it to Victorinox for warrantee repair. I don't see why it wouldn't be free aside from shipping.
-
@Max Stone said:
Hi abwaluyoThis is the layer next to the cap lifter/large flat driver.
Unfortunately there is no easy way to repair a bent liner at the pivot area.
Without the opportunity of inspecting the knife, it’s difficult to make an assessment.
You could try pressing the SAK together in a vice between layers of hardboard for protection. This may help press the liner flat without removing the scales. (Fold the CS out to prevent pressing it).
.....Thank you very much
What does the CS stands for? -
@kamakiri said:
I'd try a C-clamp and use some of the suggestions above. I'd open the Caplifter/SD too, to press the bent liner against it.If that doesn't work, you're probably best off sending it to Victorinox for warrantee repair. I don't see why it wouldn't be free aside from shipping.
A Clamp would be a good idea.
I'm not sure whether to send it to the Victorinox representative store in my country. but I will try to find out.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
