Next Naked Project
-
I agree it looks good

For years I used to keep a huntsman on my keys and it would not take long for them to shed their scales. -
Thanks Wim, chip

Still to decide on final layers...

-
So a naked Compact it is.

Fabricated brass scales (2mm) and central liner (0.7mm).
Corkscrew moved over one layer to keep the SAK minimum thickness. Lose the hook but I accept that sacrifice.
Still busy test fitting. A lot more difficult working with brass compared to Aluminium. Hope to finish it tomorrow. Thinking of leaving the key ring off to keep the lines super-clean.



-
Very nice job. I like the brass.
-
Brass scales have been used for ages on knives, and I think they look great! They have nice patina as they age, except on the knives I have with them, I keep polishing it off!
I have seen old bartender's knives that are pretty much a rudimentary Waiter with brass handles. And a lot of them aren't even real brass. Cheap steel (or often pot metal) plated to look like brass.
-
Looks classy!

-
That's very nice Max

-
Thanks guys.
will post some pics when done. -
Very Nice Max,
I'll pay good money for one of them!!! I like the brass, adds quite a classiness to the SAK
Piet
-
Very nice! You're doing some fantastic work there Max

-
Nice scales Max

-
Thanks Wim, magentus, Piet.

All finished! A few comments on the build...polished inside scales but left a brushed finish on the outside. Fourth pin needed to retain the blade spring is ‘blind’, corkscrew tang cut back flush with spacer. Scissors spring cut down for corkscrew space, but angled to retain some metal. Full height liner is nice, but just catches the scissors so scissor’s pivot needed a little sanding/polishing to not catch and still close with a snap.
Combo from a waiter (hole enlarged), needed some adjustment to the pivot shape to get it to close at a higher position (84mm frame lower). Spacer needed some reshaping to keep tension on Combo. 0.4mm washer needed for main blade. Would prefer older, wider tang, but did not have any left with a good edge.
Shaped the 3 scales all sandwiched together (2.5mm bolt/nuts) on a belt sander. Decided to leave the sanding ‘marks’ and not polish or round the edges. Looks and feels better. Slight counter-sunk holes to drop the peened heads slightly. Originally was going to sand flush, but decided to leave them proud as it’s fun to see (and feel) the hand peening.




-
Extra pics...




-
Very nice work Max

-
Looks great, awesome job!

-
Thanks Wim, comis

-
Really beautiful work, Max. As I said elsewhere, when you're ready to take my money please let me know. :)
I may have missed it if you posted elsewhere, but could you describe how you made your scales and liner? Are you using a milling machine?
Thanks,
Myron
-
Thanks Myron, will PM you when ready.
Old school fabrication...I bought the sheets from a local supplier (2mm and 0.7mm). Cut rough rectangular blanks with a good quality hacksaw (about 30x100mm). Coffee breaks between...
Used an existing aluminum full-size liner to mark the hole positions (with clearance for the whole scale), and drilled a 2mm blank with a Dremel on a drill press. 2.2mm on back pivot and 2.5mm on end pivots (only drilled the 2nd inner pin hole on the 0.7mm liner). Easy to be off by a tiny amount (messing the spring/pivot geometry, so looking at getting a steel jig made to guide the exact hole positions).
Used thin double-sided mounting tape to sandwich the 0.7mm between the two thicker blanks, using the top as a guide to then carefully drill through and have the holes line up.
I traced out the scale outline on the top blank with a Sharpie, matching the holes.
I then used 2.5mm hex screws and nuts through the end pivot holes to secure all 3 layers together. Screw heads on the bottom. Just finger-tight to not damage the brass (could have made up some nylon washers if necessary).
Then used the magic mounting tape to mount a short 2mm brass off-cut between the pivot holes on the bottom blank. This gives a stable/flat surface to slide the stack on the sander’s table, and not scratch the bottom plate. Had to sand the screw heads down a tiny amount as they stand just proud of 2mm.
Then used a course sanding belt (100 grit) on a small 1in bench sander (vertical belt with small flat table) to grind away all 3 blanks at the same time, making them identical. 100 grit makes short work of the brass, and leaves a nice vertical grain on the cut edge, which I’ve left.
Once shape was perfect, released the screws and I had three identically shaped scales. Then marked the 2nd inner pin hole in each of the 2mm scales and drilled a blind hole (only drilled 1mm deep), just enough to capture the short pin needed to retain the blade backspring.
Using an existing liner, traced the corkscrew cut out on one scale and the liner and again used the belt sander to cut away the shape (but each done individually).
Slight counter-sunk the pivot holes so the peened heads would be a little lower (still wanted them proud). Mirror polish on 0.7mm liner and inside of scales. Brushed finish on the outside of the scales.
That’s it!

-
Excellent work

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
