Skeletool???
-
To quote; ".....There's a bit holder that unfolds out the end of the handle with the knife blade. Two double-ended screwdriver bits (the same proprietary flattened style as used on the latest Wave and Charge, etc.) are included....."
I'm thinking the bit driver unfolds from the tool while it is in the closed position. (At least I hope they had the good sense to engineer it that way!)
I also think the carbon fiber section is just one layer among several in the "sandwich" style construction of the left handle. Perhaps its only purpose is to provide the little cutout section for the spare bit? Keep in mind that the carabiner is a single sheet of metal, folded into a channel shape, that must run all the way up to the plier pivot. (Visualize: the plier head folds down and rests <u>alongside</u> the spare bit.)
I don't see a pocket clip.
-
One would think they would show it at it's best- why would they leave the bit driver open? Strange things are afoot at the Circle K...
Def
-
Anyone else see it or am I crazy?

-
Hmmmm....maybe....but that rivet head down on the end makes me think that it isn't a pocket clip?

-
It might also be a simple ball bearing type thing to help retain the clip onto the pocket.
-
@Corrugated said:
It might also be a simple ball bearing type thing to help retain the clip onto the pocket.I hope so!! A tool like this really begs to be carried with a pocket clip.
-
It looks like it's fastened at both ends to me too.
Def
-
I was really looking forward to something by Leatherman that was along the lines of the Zilla, course now they got me wondering what is going to happen and how are they going to ruin it. Skeletool? Do I like the name? No, sounds more like Skeletor from He-Man. Would I carry it.......Only if it had a pocket clip.
That's right Leatherman, you read these forums
Listen to us tool folk, we know what were talking about!David
-
Hmmmm. Altogether now I have seen a total of five different photographs of this Freestyle/Skeletool device, and not a goll darn one of them has shown the backside of the tool, opposite the knife blade.
Maybe I'm paranoid, but it makes me think they're hiding something..... :-\
-
ok, i don't get this at all, maybe i am just being thick; what is the point of being able to fold the bit driver? Why not just fix it into a locked position? Is it to protect the bit you may have placed in it? To stop the bit from falling out when using the pliers and the handles are open?
The one major disappointing aspect of this tool (apart from its name) is that the bit driver cannot be used when the tool is closed, maybe with the way the design is there was no way for LM to make it so, either way, it is a shame, since when you open the tool it doesnt lock in any position and so IMO it becomes more difficult to use the driver (apart from the obvious point that most would prefer being able to use the driver without moving / opening anything else)
-
From the picture of the Freestyle, it looks like the bit driver doesn't fold at all (look closely -- no locking mechanism). That doesn't bother me-- I tend to use the screwdrivers with both handles opened. It makes for a longer driver, as opposed to having the handles completely closed. I like the design. All you need to do is open it up and use the driver -- 1 step. Other leathermans, you need to open the handles, pull out the driver, then close the handles back up. 3 steps.
-
Just noticed that there is no nail nick on the bit driver. The driver definately does not fold into the body. It is always out.
-
With all due respect, I disagree completely. There are several cues that point to the bit driver folding rather than remaining outside. However, as has been pointed out, it is apparently unnecessary to actually fold the driver as it doesn't seem like it would get in the way.
Def
-
I would agree, to make it more compact and pocktable it would have to have a folding driver.
David
-
Hi Def,
Go have a look at the large photos in the review that Doug Ritter did of the Freestyle. After a few ratio measurements, I conclude that the bit holder does not fold. The "pivot" you point to appears to be one of the two rivets holding the BH to the frame. I think the closed photo shown is missing the BH.
In any case, the excitement hightens - November is not too far away (sorry Bob).
Def - can you ask the difference between the two models of your contact and share that with us?
Thanks - Joe
-
I'm still undecided on this whole bit driver debate.
Def,
I think your "nail nick" might well be the channel that holds the little bit retainer spring. (Take a look at the bit driver on a Charge or a Surge and you'll see what I mean.)Joe,
I agree, the size ratios don't seem quite right to allow pivoting. Yet why else would they have the TWO large rivets so close to one another, as can be seen through the large side holes? I would think that only one rivet would be adequate if the bit driver was fixed.I dunno, I'm too wishy-washy. Despite what Joe says, November is a lifetime away. In the mean time, all we can do is speculate.
PhotoShop speculation:

-
Or are you guys imagining the bit driver folds to the inside?
-
If the bit driver folds in that way, and somehow locks at 90 degrees, then am I right in thinking it could be used when the tool is closed? If so, then thats pretty good, but again, I doubt this is the case, I might not be so sceptical if bit drivers on other LM tools locked at 90 degrees as well as 180 degrees.
-
I could be wrong as well, but if you look at the pictures of the tool closed, the driver apears to be in the same position, kinda inside the carabiner. So I am guessing it does not pivot in any direction.
-
Rainy morning here in Michigan, so I spent some time playing with my photo editor, fiddling with Def's Skeletool picture.
The first picture (below) is almost the same as the original, except that the plier jaws are closed and the knife blade is fully folded away. Nothing new here really. Note that if the bit driver discussed earlier is truly fixed in place, it would not be very usable with the tool in this position.

Next is an edit with the tool fully folded away. It appears to be a very lightweight and compact carry. (Again, I certainly hope there is a pocket clip on the back side!) Also note that a fixed bit driver cannot be used with the tool in this position.

As a matter of fact, the only really practical position for a fixed bit driver to be used is in the "stretched" position, as Spoonrobot calls it. (shown below)

Nothing wrong with screwing in the stretched position I suppose. ::)
It is a bit more awkward than screwdriving with a multitool in the fully closed position, however IMO, any type of screwdriving with a multitool is always an awkward affair. All the more reason for a ratcheting bit driver mechanism some day.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login