30-day axe challenge
-
Better day two than never...

Used my splitting maul to split up some firepit wood today. Mini Gransfors rode in my cargo pocket. It helped open some junk mail and an Amazon package once back inside. :D



-
Great uses Sheradin

-
Nice sharpness test, comis!

Nice to see you giving that axe a workout, Tazzie!

-
-
Day 1- Thanks for the kind comments, folks! It may be one of the last days for shorts here until spring, but Mini Bruks rides nicely in my right side cargo pocket. Best part is, Mrs. Sheradin hasn't noticed yet...


-
Great way to carry your axe Sheradin

-
FuzzaxeFakeaxe Day 2Sorry, not much use for the axe today, it's been a very long busy hectic day and the only cutting tools employed were my circular saw and chop saw, and both pretty much used to their limit.
However, the axe still came in useful at one point - to prop a door open when I came home so that I could put some tools and materials away...


-
Great use of the axe Fuzzy

-
Day 2
Council Tool Saddle Axe
-
I like the look of that axe

-
it looks like a fun axe. 
-
Sheradin, no worries on the late start. Label your entries, e.g. Day 1, Day, etc..... Your final post will just end up on Oct 31 as Day 30.
The mods have indicated that a 30-day Axe will be forthcoming when it can be developed. (Chief Badge-maker is wandering the streets of Paris, searching for a bowl of chili in vain.)
-
@Nix said:
Sheradin, no worries on the late start. Label your entries, e.g. Day 1, Day, etc..... Your final post will just end up on Oct 31 as Day 30.The mods have indicated that a 30-day Axe will be forthcoming when it can be developed. (Chief Badge-maker is wandering the streets of Paris, searching for a bowl of chili in vain.)
Don't you worry Nix, I'll design you a badge... It'll be all artistic like too... and edgy.

-
Day: 02
Made a mask for Lyndax today. My first attempt at an axe mask and the results were......mixed.
First, a little design work

I wanted the heel of the blade to hook in and get captured by the mask. This meant I had to be able to insert the bit and rotate it into position with enough clearance to avoid the toe cutting the sheath open. The geometry of the blade made this a bit trickier than I expected.
Obviously I wanted a welt. For added strength at the toe and beard, I thought I'd use some rivets. Normal stitching is all I think is needed for a knife sheath, but for an axe mask I thought a few safety rivets would be a good idea.
Once I had a template, I cut out my leather. Used both Lyndax and a craft knife to cut out my leather.

This might be the wrondg way to go about making a sheath, but I typically leave the welt a bit oversized, glue and stitch everything up, then trim off the excess. This may not have worked as well for me this time.

I've never used Pliobond before. The house is fairly chilly (58ºF) and the glue may not have cured very well (or maybe I rushed it....) at this temperature. Anyway the Pliobond worked well enough and merits more testing.
Once the mask was glued together, I stitched up the leading edge. I also marked out where I wanted my rivets. It turned out that I should have given myself a bigger margin, these are just a bit close to the edge. (Plenty of room for the stitching, so that's not an issue.)

Lyndax trimming the tab of the retention strap. (I thought I had brass snaps, but all I had was a dark nickel snap. Planning fail #1.)

Final step was to rivet the mask up and then work on the finishing a bit......but my rivets were too short. Planing fail #2. So I used some Chicago screws instead. These had slightly wider posts and heads....and ended up a little closer to the edge than I would have liked.
Here's the mask screwed and stained:

Despite a little design work, the mask is still pretty tight and a bit tricky to put on. I'm assuming that it will loosen up a bit and wear in. In which case, it might be perfect.
Lessons learned:
- Design a touch extra space into a mask.
- Don't rush.
- Allow ample margins, you can always trim away excess later.
- Use a glue as directed, and don't keep the house so cold.
- A little advance planning and preparation might be helpful.
- Know your materials and what you actually have in a drawer, not just your head.
-
@Fuzzbucket said:
Don't you worry Nix, I'll design you a badge... It'll be all artistic like too... and edgy.
Ahhhhh.....best to leave these things to the professionals, Fuzzy.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
