OOPS! - SAK Production Errors
-
@Rich S said:
Re: my earlier post this thread:I finally got around to looking through my SAK collection and I did find an Alox Soldier (curses-forgot to check the year) that <u>does</u> have a sharpened inside curve on the screwdriver. Amazing what you find out on the board. :)
RichOh cool, one of the older ones then!

-
@Rich S said:
Re: my earlier post this thread:I finally got around to looking through my SAK collection and I did find an Alox Soldier (curses-forgot to check the year) that <u>does</u> have a sharpened inside curve on the screwdriver. Amazing what you find out on the board. :)
RichHey Rich,
Some of my Pioneers have this too. This early one has both the ground edge and the wire bender/stripper:

And as you note, some earlier Model 1961's. These are both '65's:

And I also have an 84 mm cellidor SAK (Salesman, I think?) that has both the ground stripper edge, and the wire stripping notch (lower right in picture):

I wish Vx still did this to the cap lifter tool. It's a useful feature.
Myron
-
Some of my Pioneers have this too. This early one has both the ground edge and the wire bender/stripper:

And as you note, some earlier Model 1961's. These are both '65's:

And I also have an 84 mm cellidor SAK (Salesman, I think?) that has both the ground stripper edge, and the wire stripping notch (lower right in picture):

I wish Vx still did this to the cap lifter tool. It's a useful feature.
Myron
Very nice SAK’s

-
@moonweasel said:
Not sure I would call it a production error, but I still find it a bit amusing.

It took me a minute to get this
-
'72 246fmaU Champion 'A':


I don't normally chase models with boxes, but how often does one come NIB/MIB with an unsharpened awl? It does have the concave grind, but no edge and no tip grind. And to my knowledge, it wasn't a display model...and everything else is sharp.
-
@fullbreakfast said:
If collecting SAKs was like collecting stamps these would be worth a fortune.Kinda works for the rare functionally defective models like SwissFlame or Autotool.
-
Rediscovered this today on an early '80s Ranger:

And if it's not clear in the pic, the pair of cuts toward the tip aren't as deep, and the tip is deeper than a wood saw should be of this era (post '79 with the bump in the backspring tip) and is 'in line' with the bulk of the saw teeth tips. Minor error, but I think it might have come loose from the jig or perhaps the cutting wheel shattered on that last pair of cuts.
-
@kamakiri said:
Rediscovered this today on an early '80s Ranger:
And if it's not clear in the pic, the pair of cuts toward the tip aren't as deep, and the tip is deeper than a wood saw should be of this era (post '79 with the bump in the backspring tip) and is 'in line' with the bulk of the saw teeth tips. Minor error, but I think it might have come loose from the jig or perhaps the cutting wheel shattered on that last pair of cuts.
expert eyes
doubt I'd catch that 
-
Not sure if it’s really an error.
I’m guessing it’s just worn tools on the production line that couldn’t cut quite close enough and it left a bit of excess material on there.
They were only small flakes so just lightly scraped them off with some ceramic tweezers.
Before:

After:

-
@KeepCalmCarryOn said:
Not sure if it’s really an error.
I’m guessing it’s just worn tools on the production line that couldn’t cut quite close enough and it left a bit of excess material on there.
They were only small flakes so just lightly scraped them off with some ceramic tweezers.
Before:

After:

-
@KeepCalmCarryOn said:
Not sure if it’s really an error.
I’m guessing it’s just worn tools on the production line that couldn’t cut quite close enough and it left a bit of excess material on there.
They were only small flakes so just lightly scraped them off with some ceramic tweezers.
Before:

After:

Thats how an unused saw of victorinox looks like, not an error. With scraping it of, you make it an used tool and decreased the value around 50 % :-)
-
Ceramic tweezers...never heard of those but thats a great job you did on that saw blade!

-
@KeepCalmCarryOn said:
Not sure if it’s really an error.
I’m guessing it’s just worn tools on the production line that couldn’t cut quite close enough and it left a bit of excess material on there.
They were only small flakes so just lightly scraped them off with some ceramic tweezers.
Before:

After:

Ohh... It's not an error, i can assure you...
All my saw's look like that before first use. After the first branch cut or two it's fine and clean

My new Camper looks the same, haven't had any saw use yet.

-
@Rapidray said:
Ceramic tweezers...never heard of those but thats a great job you did on that saw blade!

They’re for vaping, so I can fire it and adjust the coil at the same time, I assume metal ones would be a little shocking :D
Cheers for all the other responses, not had it on any of my new saws before.
-

And there are more obvious errors out there:

Super rare +PAT+ version of the can opener.


I guess this one didn't leave the jig before it got hit again!
So somewhere out there there might be a PAT stamp missing its '+'.
-
From another thread:
@Syph007 said:
I took apart a compact the other day and the combo tool had been stamped from the thicker steel that the bottle opener and can opener would be made from. It was so thick the sak was bulging at that end. First time Id see that one.@jazzbass said:
2mm thick? I have a Mechanic Jr that's the same. I always assumed it was 111mm combo tool that was used (intentionally or accidentally) and not a stamping error. Not sure what the pin diameter is on 111mm knives though - 2.5mm? 3mm? If the 111mm knives have bigger pins that would answer the question pretty easily.@Syph007 said:
It had a 2.5mm hole. Was identical to a standard 91mm except for thickness. -
Haven't seen this before...OOPS!

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
