30-day axe challenge
-
Day 15
Per Fuzzy request, butt shot of Chip Chop! :D

-
@styx said:
day 14: this challenge just got to the hard part, my classes started<a href="https://flic.kr/p/2huJDiq" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/48895582902_d158b6100e_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
Nice

-
@Nix said:
Day: 14 (unofficial photo)I cheated today......

While I was at the gun range today, my earplugs broke, leaving the green baffles inside my ear canal. (Not seen in the picture, there are usually two ends to these earplugs: a green full silence end and a yellow end that lets some noise in. When I tried to pull these plugs out, BOTH of the yellow ends came off, leaving the green bits stuck in me ear canals!)
Back in the truck, I couldn't figure out how to use Lyndax to remove just the earplugs, so I resorted to using a Leatherman ST300 to reach into my ears and remove the plugs. This is an unanticipated shortcoming of the axe. Live and learn, I suppose.......
Nice looking Ruger!

-
@Noa Isumi said:
Day14
Decided to save the left over roast for tomorrow and do breakfast for dinner.Since I didnt do much here is the newest Townsed vid going over the tools he used in cabin including a bunch of axes
https://youtu.be/xkmyK8XqVpQVery nice!

-
Day 15
I brought Bruce to work today. His edge was threatening to slice me up so I wrapped him in electrical tape.
I think one of the reasons for excessive up and down head movement is a hump in the bottom of the eye. I'm in the process of filing it out and tidying up some sharp corners. My hope is that I'll get more head to handle contact all around. This may mean my current handle will no longer fit but if it does I might shorten it and make the hickory the long one. If it doesn't fit then too bad, I guess!
Sent from my SM-G970F using Tapatalk



-
Polls. Bruce doesn't have a very big poll, but it is bigger than a builders hammer or 20 odd ounce ball peen. It's a bit wonky, but I'm not going to bother filing or grinding it
Sent from my SM-G970F using Tapatalk



-
I used a little sandpaper to smooth out some of Lyndax's rough edges in the eye. I think it helped.

-
Day: 14 (official photo)
No uses today. The Supertool was the only tool I actually used today. And that was just for an emergency medical intervention.....

-
@TazzieRob said:
Day 15I brought Bruce to work today. His edge was threatening to slice me up so I wrapped him in electrical tape.
I think one of the reasons for excessive up and down head movement is a hump in the bottom of the eye. I'm in the process of filing it out and tidying up some sharp corners. My hope is that I'll get more head to handle contact all around. This may mean my current handle will no longer fit but if it does I might shorten it and make the hickory the long one. If it doesn't fit then too bad, I guess!
Sent from my SM-G970F using Tapatalk
Nice job you did there!

-
Great pics again everyone

-
@TazzieRob said:
Day 15I brought Bruce to work today. His edge was threatening to slice me up so I wrapped him in electrical tape.
I think one of the reasons for excessive up and down head movement is a hump in the bottom of the eye. I'm in the process of filing it out and tidying up some sharp corners. My hope is that I'll get more head to handle contact all around. This may mean my current handle will no longer fit but if it does I might shorten it and make the hickory the long one. If it doesn't fit then too bad, I guess!
Sent from my SM-G970F using Tapatalk
Nice photos showing the fix. I think I have a coldsteel tomahawk somewhere, and remembered it used to get loosen from time to time. Maybe it was a similar reason, or the sharp edges are digging into the handle too much. I gonna look that up sometime, good call!
-
Day 12 I know the benchmark is a block of cheese but i'm not quite ready for that yet so went with the good old Swiss roll, baby steps i know but the little axe destroyed it, just like a knife through butter


-
@TazzieRob said:
Day 15I brought Bruce to work today. His edge was threatening to slice me up so I wrapped him in electrical tape.
I think one of the reasons for excessive up and down head movement is a hump in the bottom of the eye. I'm in the process of filing it out and tidying up some sharp corners. My hope is that I'll get more head to handle contact all around. This may mean my current handle will no longer fit but if it does I might shorten it and make the hickory the long one. If it doesn't fit then too bad, I guess!
Sent from my SM-G970F using Tapatalk
Makes sense, good fix

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

