What did you use your Leatherman for today?
-
@alexanderre said:
Later I started tinkering with treble bleed addition to my Fender Telecaster, so in order to make testing of different cap+resistor combinations I created a short cable with alligators on both sides. Cutting, stripping with a Signal again, but also crimping this timeCool... now can you fix the wiring on my Strat? ;)
-
On vacation and busted my watch today. Found a Casio on sale that should keep me till we get home.
Had to cut the wire cable, security tag, off with my sidekick that lives in the console.

-
Sorry to hear that you busted your watch

But your new one looks a good one PC

-
@PitCarver said:
On vacation and busted my watch today. Found a Casio on sale that should keep me till we get home.Had to cut the wire cable, security tag, off with my sidekick that lives in the console.
Oh boy, I hope it wasn’t something special!
Nice usage
-
@Rapidray said:
Oh boy, I hope it wasn’t something special!
Nice usage
Christmas gift from a couple years back. Casio is smaller than I like but I can still read it without my cheaters.
@Wspeed said:
Sorry to hear that you busted your watch
But your new one looks a good one PC

I'm more mad, now, that I didn't salvage the battery, when I tossed it.
-
Used my ST300 straight blade to cut a small zip tie.
Used Rev pliers to push in spring loaded shaft.
-
Nice work BM

-
Using it to pass the slow hours at work.


Sent from my LG-SP200 using Tapatalk
-
@BadMechanic said:
Using it to pass the slow hours at work.

Sent from my LG-SP200 using Tapatalk
Nice BO!

-
Was working on the car to find a rattling noise. After getting that taken care of, used the Crunch to cut the cold of a severely beat up oil pan heater. Closed the hood and noticed it was not closed properly. Used the hood release inside the car, and it was fully disengaged, yet I could not open the hood nor close it it down.
Used the Crunch and its file to reset the hood latch. Went to close the tools up and the file fell off. :ahhh Crystallized metal. /sigh
So, off to the fatherland for it (Leatherman HQ) to get repaired, and maybe they can look at those blasted pliers that won't stay shot. /grr

-
Oh no!!!! ???
-
@Outback in Idaho said:
Was working on the car to find a rattling noise. After getting that taken care of, used the Crunch to cut the cold of a severely beat up oil pan heater. Closed the hood and noticed it was not closed properly. Used the hood release inside the car, and it was fully disengaged, yet I could not open the hood nor close it it down.Used the Crunch and its file to reset the hood latch. Went to close the tools up and the file fell off. :ahhh Crystallized metal. /sigh
So, off to the fatherland for it (Leatherman HQ) to get repaired, and maybe they can look at those blasted pliers that won't stay shot. /grr

Got to love that warranty
-
@Outback in Idaho said:
Was working on the car to find a rattling noise. After getting that taken care of, used the Crunch to cut the cold of a severely beat up oil pan heater. Closed the hood and noticed it was not closed properly. Used the hood release inside the car, and it was fully disengaged, yet I could not open the hood nor close it it down.Used the Crunch and its file to reset the hood latch. Went to close the tools up and the file fell off. :ahhh Crystallized metal. /sigh
So, off to the fatherland for it (Leatherman HQ) to get repaired, and maybe they can look at those blasted pliers that won't stay shot. /grr

Oh boy

At least it’s fixable -
Had some spare time at work today - decided to clean up around a little. Among many other improvements disassembled and cleaned my tiny Bialetti espresso maker. Used a can opener to lift and remove a rubber part.

Next I found out that filtering part needs a bit of special attention. Since I don’t have a Swiss Champ or any other SAK with a pin - had to improvise [emoji2]

Anyways moments later the unit was again refreshed, proud and ready [emoji1305]

-
All those coffee machines need leaning! Great usage

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



