Who owns a Buck 110?
-
Does the blade hit the rivet on the inside of the handle

-
This is just speculation, but I wonder if that is done on purpose? What I mean - Does ebony tend to shrink as it dries out? If they finish it with more material, it would accommodate this to some degree. Or it could just be a six sigma item for Buck to deal with.
-
@zrxoa1 said:
Now that my Crunch challenge has ended (I only went for the 15 day mark...), I have decided to go back to my 110 D2 Slim Pro as my daily carry.

I have noticed some nicking towards the blade tip. Some have complained that the heat treat was not done right on these knives. I have not used the blade hard yet I have nicks. Maybe they’re correct??


Sent from my iPhone using Tapatalk
It is a great looking knife, sorry to hear about the nicks

-
@Wspeed said:
Does the blade hit the rivet on the inside of the handle
That might be it, there’s no rivet but there is a part at the end.


But you really have to push hard for the blade to hit that end piece. It doesn’t do it when letting the blade snap shut.
Hmmm, not really sure what’s going on. I’m carrying it today. See what I can cut on to see if any more damage shows up.
[emoji1303]
Sent from my iPhone using Tapatalk
-
Does the bolster not hit something stopping the blade hitting anything.
-
Luckily they don’t seem to be very deep
Hopefully you can remove them easily
And then see if it will happen again
-
@Dunc said:
Gentlemen what are your thoughts on this YouTube video. The guy claims the Ebony scales on his new production 110 have swelled. Basically the wood is a little raised where it meets the brass on the corners and you can catch your nail on it. Mine too is exactly like this but it was like it when it was new and I can’t say it’s got worse. Personally I don’t think it’s swelling and more a case of not finished flush in the factory.I made it a little over half way through the video before shutting it off. I kept thinking its better to be perceived as not being very bright than to open your mouth and remove all doubt.

-
@zrxoa1 said:
Really hard to catch the nicks AND hold the phone/camera, but here you can see TWO nicks. They can’t both be caused but the blade hitting when shut.

Sent from my iPhone using Tapatalk
Probably after you get sharpened past the thin factory edge you wont have any more chipping problems. I've had numerous knives do this over the years. Mostly with higher grade steels.
-
@zrxoa1 said:
That might be it, there’s no rivet but there is a part at the end.


But you really have to push hard for the blade to hit that end piece. It doesn’t do it when letting the blade snap shut.
Hmmm, not really sure what’s going on. I’m carrying it today. See what I can cut on to see if any more damage shows up.
[emoji1303]
Sent from my iPhone using Tapatalk

-
Thought I’d share these
1B5236A5-A648-4EA9-8D64-815A85CF4BDC by Duncan Moore, on Flickr
DA2D4965-829E-4E77-BCB5-7D8F97A92617 by Duncan Moore, on Flickr
3BC9BE90-6E55-40ED-AEC4-E3EAA92ED62B by Duncan Moore, on Flickr
8FB175BC-189B-4952-AD23-58E19F3D4BF2 by Duncan Moore, on Flickr -
Nice ones Dunc and nice pics

-
Thanks Wspeed
-
My grandpa’s 110. Needs some love from Buck. I’m just hesitant to send it in. 72 to 86 I believe.

-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
