ZapWizard's Leatherman Free P4 Mods
-
@ZapWizard said:
I have a torque meter at work that I can borrow to measure the existing torque on those screws. My P4 has been taken apart, but I have only messed with one screw on my P2. So In theory, I can use the torque wrench to measure how much it takes before they tighten/loosen to see what the existing torque is. But then to repeat that you need a torque wrench anyways.In reality you can do this just by hand like I do in my videos. You get a feel for the tension and adjust it looser/tighter.
This has been requested a few times, and I have put some thought into it. It probably would have to be done as an open loop. I may take another crack at the design soon, now that I know the open loop is stronger than I expected.
The catch is it wouldn't hold any bits, as they would be shoved up against the belt. I have been thinking of making a stand-along bit holder for the flat bits, something that could be removed from the belt and used as a handle on the extender.Any luck with the torque meter?
Still haven’t found time to do the install yet, but maybe I’ll take a crack at it today...at the very least, the thumb tabs are going in!
————
As for the horizontal carry...This might be a stretch of an idea, but...
Picture the holster standing vertically:
-
What if you moved the Bit Extender to the left of the main channel, which would put it “on top” of the holster, when mounted on the belt...assuming it’s mounted on someone’s right side.
-
Then, take the beautifully designed Bit holder slots and put them to the right of the main channel, which would put them on the “bottom” of the holster...
Removing the Bits from the back face of the holster would provide access to them on a horizontal carry.
-
-
@Dutch_Tooler said:
Meanwhile...
Box from Shapeways... :ahhh
I was wrong... the holster only holds three bits since the variant I chose for longevity's sake is the one to which one can fit a metal belt clip (which hasn't arrived yet). No great deal. The bit driver fits like a glove and works well

Thanks are due to ZapWizard for his designs

I like that compactness

-
Love the sheath and the bit holder
I have a sheath from Zap that holds the Wave/Charge tools with room for bits in the back and the extender on the side and am very pleased with it

-
Playing around with the holster I conclude it is a very well thought out piece of kit. The Free P4 fits in four ways if you take the pocket clip off, two ways if you leave it on, including two or one respectively with extended implements (although I'd be careful doing that with the long tools, especially the bladed ones ;) ). It uses the locks on the Free to lock the tool inside the holster, irrespective of how you put it in, so there is no falling out.
The integrated bit holders are a nice feature for frequently used bits - although the number of three is a bit limited - this is down to my choice for the metal belt clip variant, other variants have 6 or 7 spaces I think. The bit extender holder works well too. The whole thing seems quite solid, but I won't know to which extent until after I start to wear it.
Final verdict on wearability once the belt clip arrives (taking the slow boat from China, it seems).I have thought of adding some extra holders for saw/file blades and long MUT bits, but can't seem to find anything that integrates well with the holster design while avoiding a haphazard DIY look and thus detracting from its otherwise professional look - also on balance I think I may need to carry at least one LM bit card for flexibility. I'll probably end up assembling some kit in a small extra holster or pouch.
-
Can't wait to see what you come up with, DT


-
@Dutch_Tooler said:
Box from Shapeways...Your kit looks great.
@hbcorpse said:
Any luck with the torque meter?As for the horizontal carry...
I don't think the torque meter will help, it is easy to just tweak it until the tools move properly. Because they used chemical thread locker, torque is less a factor in holding the screw in place.
I am working on a few ideas for horizontal carry, however it won't include bit holders, as you would only end up with just a few, or an oversized holder. Most who have requested horizontal carry want less bulk above/below the belt line.@Dutch_Tooler said:
Playing around with the holster I conclude it is a very well thought out piece of kit.Thanks for your nice comments.
- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
I also got a box from Shapeways, my 2nd prototype of the T-Shank holder arrived. It shows real promise. I will cycle exchanging the blades a few dozen times to ensure the nylon will hold up, but so far it seems to be close to being ready.
I just need to tweak the profile so it closes/opens a bit better, and tweak a bit of the dimensions to make it work out of the box. -
Looking great

How much thickness will one have to grind off from a LM shank?
-
@Dutch_Tooler said:
How much thickness will one have to grind off from a LM shank?Just 0.2mm the Bosh is 2.2mm wide, the LM is 2.4mm wide. (and a bit of the actual T portion) It takes a bit of time and care, but easy enough if you test fit it as you go.
The bigger thing I messed up was cutting the file to length. I cut it a bit short, and it can move out when the pliers deploy. I will have to order another file and try with a more exact measurement, and perhaps a template to keep the cut even. -
Very good news about the prototype, Zap

-
My bit holder for the P4 and custom ST300 sheath arrived and I am super happy with how they turned out.
Really excited for the t-shank adapter. Will it fit in the slot with the scissors or just the saw side? Since I carry a SAK for scissors and openers, it would be nice to ditch the scissors on the P4 and replace with a t-shank holder for the LM file...
-
Got my Flat Bit mod installed yesterday!
Wow! What a difference!
I’ll admit there was a small hint of buyer’s remorse / regret for modifying a perfectly fine Free P4...and voiding the warranty...not to mention the analysis paralysis of wondering if it’s the right modification to make, and lose the stock pry-bar/flat head + cross head inserts...
But the more I think about it, the more I’m happy with the mod, and glad I’ll be able to utilize the Flat Bit kit that I always carry.
Thanks Zap, and all those who have contributed / driven this thread, and sparked the innovation and creation of these mods!
-
Meanwhile on a different continent, a pocket clip has arrived from over the pond so I could finally complete the holster.
I have used blind rivets (4mm wide, 8mm long) with washers to fix the clip and this works well enough as well as being very stable, more so than Chicago screws probably. There is a slight binding in the more rarely used locks-up position of the P4, but there is enough flex to get the tool out anyway. I might go for Chicago screws if this ends up bothering me more than it does now. No problem in the locks-down position.
The holster carries well, I've had it on my belt for an hour and soon forgot I was carrying it :D

-
Well don't count your chickens until they hatch. There are a few issues with the current T-Shank holder that I am trying to work out.
[list type=decimal]-
The nylon and metal don't have the same shrink ratio. So despite having identical geometry for say opening/locking, it works perfectly on the metal, and it binding on the nylon. Also the nylon thickness expanded compared to the CAD model by 0.2mm. Small, but big enough that it is causing issues with smooth deployment.
-
The nylon spring works, but ends up flexing the whole piece a bit, making smooth operation with a thick blade problematic.
-
The stainless steel material used is not highly magnetic, so the T-Shank isn't staying docked as well as it should, exasperated by the low amount of contact surface to the magnet.
I am re-designing it yet again, trying to put more metal against he magnet, and working around the various thickness issues. So no promises on when it will be available.
@Toolslinger said:
My bit holder for the P4 and custom ST300 sheath arrived and I am super happy with how they turned out.Really excited for the t-shank adapter. Will it fit in the slot with the scissors or just the saw side? Since I carry a SAK for scissors and openers, it would be nice to ditch the scissors on the P4 and replace with a t-shank holder for the LM file...
Glad you like the bits. I have been using my black bronze steel version a lot lately. Fixing all sorts of stuff around the house.
The current Rev 2 design would have to be where the saw is only due to the built-in thumb tab (And I need that precious amount of extra material that spots allows)@hbcorpse said:
I’ll admit there was a small hint of buyer’s remorse / regret for modifying a perfectly fine Free P4...and voiding the warranty...You can probably re-assemble it back to stock if you ever needed a repair if another implement broke.
@Dutch_Tooler said:
The holster carries well, I've had it on my belt for an hour and soon forgot I was carrying it :DIt looks great. You can also use flat-head screws, in combination with the other half of a Chicago screw if you want something even lower profile. You can always sand down the edges of a flat-head to make it not catch/stratch on a belt.
-
-
:D

-
@Dutch_Tooler said:
:DThat looks great!

-
8) I will be glad when I can carry my Charge or Wave again and get to use my Zap wizard sheath :ahhh -
great job on the blade adapter!
You kept the original file and removed the can opener.- I wonder if the original short file could be removed and the can opener kept on?
- Is there a mod where the P4 can be made wider so it can accomodate the new pieces without getting rid of the original ones?
-
@carl, if I may butt in:
- Can opener is .13" IIRC, file is either .07 or .06". Assuming you refer to the situation with the bit holder taking up all of the central position (between the springs) of the handle it sits in, you'd have to remove the file and something else, e.g. the ruler or awl, to make place for the can opener/Phillips in the opposite handle.
- Unlikely... the width is dependent on the studs in the plier head that slot into the handles when opened - widening the handles to accommodate more tools requires wider plier head stud placement, i.e. a new plier head. Note these are already different between P2 and P4. There has been speculation about a possible "P6" but this has failed to materialise until now.
Hope this helps.
-
@Dutch_Tooler said:
..... I'll probably end up assembling some kit in a small extra holster or pouch.Got me a small Skinth. Modded the bit cards a little bit to make them shorter so they fit in the Skinth's main compartment while the long bits go into the front pocket. The main compartment also hosts the saw and file blade in preparation for the eventual arrival of a T-shank blade holder. These blades will need to be shortened slightly, BTW, to fold inside the tool, I gather. There is more space for saw blades of all kinds, including diamond powder coated ones, if reasonably short or shortened to fit.



Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login