Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Sharpening with Paper Wheels

Scheduled Pinned Locked Moved Edged Tools
67 Posts 1 Posters 22.9k Views
  1. Home
  2. Tool Talk
  3. Edged Tools
  4. Sharpening with Paper Wheels
Sharpening with Paper Wheels
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • kwakster Offline
    kwakster
    Posts: 1,006
    kwakster Offline
    kwakster
    wrote on last edited by
    #54 Quote Reply

      Right hand Takamura R2 Gyuto 210 mm from a local Chef, who got it as a birthday present from his wife.
      The knife has already been used for two months in the commercial kitchen and it was time for it's first resharpening, which i did yesterday on a Paper Wheel with 15 micron diamond compound and then deburred on a second Paper Wheel with 0.25 micron diamond compound.
      The idea was to make an edge that would do both slicing & pushcutting well, and also to remove as little steel as possible from the fine and thin R2/SG2 blade @ 63-64 HRC.
      The new edge measures +/- 20 degrees inclusive and can whittle a chest hair from root-to-tip at about 4 centimeters from the point of holding, and after a few test cuts into a old piece of beechwood cutting board.

      I took these pics with an old Ipad and actually wanted to erase them again as being not good enough until i enlarged the last picture twice.
      At first i thought i saw small dirt spots on the new bevel, but those tiny white specks were actually the sliced off peaks of the micro-dot structure on the inside of the flimsy plastic blade protector sleeve.

      1 Reply Last reply
      • Sparky415 Offline
        Sparky415
        Posts: 13,000
        Sparky415 Offline
        Sparky415
        wrote on last edited by
        #55 Quote Reply

          @Sparky415 said:

          @Sparky415 said:

          Thank you K, :salute:
          Always interesting stuff and stunning pictures :tu:

          At risk of repeating myself here :imws:

          :imws:

          :salute: :cheers:

          1 Reply Last reply
          • kwakster Offline
            kwakster
            Posts: 1,006
            kwakster Offline
            kwakster
            wrote on last edited by
            #56 Quote Reply

              The owner of the Takamura R2 just sent me the link to this clip, in which he uses a grape to test the new edge:

              https://m.youtube.com/watch?v=ID9KZW0d9ss&feature=youtu.be

              1 Reply Last reply
              • Sparky415 Offline
                Sparky415
                Posts: 13,000
                Sparky415 Offline
                Sparky415
                wrote on last edited by
                #57 Quote Reply

                  :sa: :sa: :sa:

                  1 Reply Last reply
                  • NutSAK Offline
                    NutSAK
                    Admin Team
                    Posts: 8,463
                    NutSAK Offline
                    NutSAK
                    Admin Team
                    wrote on last edited by
                    #58 Quote Reply

                      That last slice through the grape.... ridiculous!

                      :salute:

                      1 Reply Last reply
                      • kwakster Offline
                        kwakster
                        Posts: 1,006
                        kwakster Offline
                        kwakster
                        wrote on last edited by
                        #59 Quote Reply

                          Update on the Takamura R2 210 Gyuto:

                          According to the Chef this edge done on Paper Wheels lasted him 2 months in his commercial kitchen, which was just as long as the factory edge had lasted him.
                          During that time he sometimes touched up the edge by stropping it on an MDF strop with 1.0 micron diamond compound until that no longer worked satisfactory (in the last week or so), after which he used a fine ceramic rod on it.
                          Differences with the factory edge were that the Paper Wheel edge had a slightly smaller edge angle (+/- 20 degrees inclusive instead of +/- 22,5 degrees inclusive), was finer polished, and had a higher sharpness.

                          We're still in the process of finetuning the edge to his specific requirements, and next time he brings in the knife it will probably get a little less refined edge to see if it's useful life can be prolonged a bit more.
                          In his kitchen the real edge killers are the mandatory plastic cutting boards which are very abrasive on knife edges, together with the almost unavoidable tiny sand particles which sometimes remain in the huge quantities of vegetables that need to be processed.

                          1 Reply Last reply
                          • Sparky415 Offline
                            Sparky415
                            Posts: 13,000
                            Sparky415 Offline
                            Sparky415
                            wrote on last edited by
                            #60 Quote Reply

                              :salute: :popcorn:

                              1 Reply Last reply
                              • kwakster Offline
                                kwakster
                                Posts: 1,006
                                kwakster Offline
                                kwakster
                                wrote on last edited by
                                #61 Quote Reply

                                  Italian made A.G.A Campolin Maltese stiletto from a collector.
                                  The knife was recently bought brand new from a foreign shop, but it came with quite a lot of blade play, a very rough ~55 degrees inclusive "edge" with a big burr still attached to it, and no point at all.
                                  Also both sides of the blade aren't mirror images of each other, with a center ridge that is off a bit on one side.
                                  Anyway, especially the lack of a point bothered the owner, the bad edge came in second, and fixing the blade play will probably be a job for another day.
                                  This is how the knife looked before resharpening:

                                  And how the knife looks now.
                                  While keeping the edge angle about the same so the bevels would not widen too much per owner's request, i resharpened the main edge completely and the bayonet grind only superficially to come to a sharp point with a 15 micron diamond compound Paper Wheel, then cleaned up the bevels a bit and removed the tiny burr with a 1.0 micron diamond compound Paper Wheel.
                                  The edge angle again measures ~55 degrees inclusive, yet the new apex is just sharp enough to shave the hair on the back of my hand a bit on skin level.

                                  1 Reply Last reply
                                  • Sparky415 Offline
                                    Sparky415
                                    Posts: 13,000
                                    Sparky415 Offline
                                    Sparky415
                                    wrote on last edited by
                                    #62 Quote Reply

                                      Always good to see what you've been up to Kwakster :salute:

                                      :cheers:

                                      1 Reply Last reply
                                      • kwakster Offline
                                        kwakster
                                        Posts: 1,006
                                        kwakster Offline
                                        kwakster
                                        wrote on last edited by
                                        #63 Quote Reply

                                          The first owner of this small Sebenza apparently thought it a good idea to use the knife for sharpening practice in his new Wicked Edge.
                                          The outcome made him sell the knife for a measly 150 Euro's to owner number two, who sent it to me with the request to tidy things up a bit and give it a bit of a shiny edge.

                                          Below is what the knife looked like when i received it, still with it's very rough and partly unapexed "edge", and with an edge angle of ~40 degrees inclusive at the straight part of the edge, changing into ~45 degrees inclusive from belly to point.

                                          1 Reply Last reply
                                          • kwakster Offline
                                            kwakster
                                            Posts: 1,006
                                            kwakster Offline
                                            kwakster
                                            wrote on last edited by
                                            #64 Quote Reply

                                              After reprofiling & sharpening on a Paper Wheel with 15 micron diamond compound, then deburring and polishing it a bit with a second Paper Wheel coated with 1.0 micron diamond compound.
                                              The new edge is a bit convex, and measures ~30 degrees inclusive on the straight part of the edge, changing into ~35 degrees inclusive from belly to point.
                                              This to avoid widening the bevels there too much, as this blade is relatively thick behind the edge in that area.
                                              The last picture shows a small facet at the heel which has an entirely different angle, so i could not remove it without making things worse.
                                              Visually it's not perfect yet treetopping sharp, and the owner was happy.

                                              1 Reply Last reply
                                              • kwakster Offline
                                                kwakster
                                                Posts: 1,006
                                                kwakster Offline
                                                kwakster
                                                wrote on last edited by
                                                #65 Quote Reply

                                                  User LH Sebenza Micarta with it's blade made from Devin Thomas stainless basketweave damascus (AEB-L and 304)
                                                  Reprofiled & sharpened the old slightly convex edge with it's apex @ ~40 degrees inclusive into a new slightly convex edge with an apex @ ~30 degrees inclusive on a Paper Wheel with 15 micron diamond compound, then removed the extremely fine burr on a piece of copypaper with a dab of 0.25 micron diamond paste.
                                                  The new apex is reverse chest hair whittling sharp and the new point is also quite close to being centered again.
                                                  To my functioning eye the bevels look near-mirror like, but the camera sees a bit blotchy scratch pattern due to the different layers in the damascus steel.

                                                  Before:

                                                  After:

                                                  1 Reply Last reply
                                                  • zoidberg Offline
                                                    zoidberg
                                                    Posts: 38,161
                                                    zoidberg Offline
                                                    zoidberg
                                                    wrote on last edited by
                                                    #66 Quote Reply

                                                      @kwakster said:
                                                      User LH Sebenza

                                                      Yes a lefty!! Nice work kwakster. :tu: :like:

                                                      1 Reply Last reply

                                                      Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                      Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                      With your input, this post could be even better 💗

                                                      Register Login

                                                      • 1
                                                      • 2
                                                      • 3
                                                      • 4
                                                      1. Home
                                                      2. Tool Talk
                                                      3. Edged Tools
                                                      4. Sharpening with Paper Wheels
                                                      Reply
                                                      • Reply as topic
                                                      Log in to reply
                                                      COMMUNITY LINKS
                                                      EDC-TV SAKWiki GearFeed SAKSelector
                                                      Operational Funds

                                                      Help us keep the Unworkable working!

                                                      Make A Donation
                                                      November Goal: $300.00
                                                      Due Date: Nov 30
                                                      Total Receipts: $0.00
                                                      Below Goal: $300.00
                                                      0% funded
                                                      • Login

                                                      • Don't have an account? Register

                                                      • Login or register to search.
                                                      • First post
                                                        Last post
                                                      0