Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

How to guide - swapping corkscrew for Phillips

Scheduled Pinned Locked Moved The Mod Squad
15 Posts 1 Posters 6.2k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. How to guide - swapping corkscrew for Phillips
How to guide - swapping corkscrew for Phillips
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Max Stone Offline
    Max Stone
    Posts: 5,982
    Max Stone Offline
    Max Stone
    wrote on last edited by
    #3 Quote Reply

      Next is to prep the replacement rod. It needs to be 2.2mm and about 1.5x the width of the SAK in length, so you’ll be left with something to peen.

      Create a head on one side of the rod. I sandwich it in hardboard in my vice and use a ball hammer to tap out a head. Test the head in a spare liner to ensure the rod fits and the head is a good size and will be secure.

      6394B9E7-8722-4CE6-84BC-DB2C91BEC84D.jpeg

      F3A37FAB-6CE8-4CED-85DE-7091A7D22D78.jpeg

      D619409A-40C1-4823-BCDE-29320CA4B7C3.jpeg

      1 Reply Last reply
      • Max Stone Offline
        Max Stone
        Posts: 5,982
        Max Stone Offline
        Max Stone
        wrote on last edited by
        #4 Quote Reply

          Now for the transplant.

          Position the Phillips in the layer, in the correct orientation. As there’s still tension on the backspring, you’ll need to press the Phillips against the backspring to get the new rod to enter the pivot hole.

          It may help to clamp the Phillips (correct orientation), to help press it in while you push in the rod. I shaped the rod tip slightly round, and a light tap was all that was needed to drive the rod into the pivot hole.

          Once you’ve got the new rod started, you can reposition the SAK above your vice and gently tap down the new rod, pushing the old one down as you go. This keeps all the tools/backsprings in place at all times and is the ‘magic’ of this technique.

          Eventually the old rod will drop out (keep it), and you’re new rod is in position.

          Cut the rod leaving about 1.5mm and peen a head to lock the layers. And you’re done! :salute:

          DF287E7E-A442-437F-86DD-C7F81F1D0E5B.jpeg

          116E530C-DF4B-4A2C-9383-43C973FFE13F.jpeg

          41922E02-9A06-4E53-99B2-91B3F2CB14FF.jpeg

          E0023A04-ABED-41F4-B1BB-4B2346E0B08E.jpeg

          1 Reply Last reply
          • Max Stone Offline
            Max Stone
            Posts: 5,982
            Max Stone Offline
            Max Stone
            wrote on last edited by
            #5 Quote Reply

              Remember I said to keep the old rod you pushed out?

              Well, this rod can be trimmed and used as the new rod on the donor SAK if it’s long enough. This saves you some rod and it already has a factory head.

              My donor was a 2-layer Small Tinker, and the target was a 6-layer Craftsman (was a Handyman while it had the corkscrew), so the rod was plenty long to trim and reuse.

              Small Tinker that donated its Phillips got back the corkscrew and become a Tourist.

              Everyone was happy with their new identities! :pok:

              I hope that some people will find this technique useful. I may well use it again when I just need to swap around a single tool. Certainly beats disassembling the entire SAK. :cheers:

              6CF98ED1-A8BA-4324-BE58-929DB4F9A45C.jpeg

              76B6FA65-C2B1-4B53-B3EC-763EA3E49D9B.jpeg

              C03D2926-8B07-4CD2-A773-DECDCC1DF8F7.jpeg

              BA824ACF-20C7-4DEF-B2E7-72FA7A04AD13.jpeg

              1 Reply Last reply
              • Max Stone Offline
                Max Stone
                Posts: 5,982
                Max Stone Offline
                Max Stone
                wrote on last edited by
                #6 Quote Reply

                  Bonus pic...the SAKs with the swapped tools...

                  6A1484DD-88AB-4B57-9D1F-B2FE700F7944.jpeg

                  1 Reply Last reply
                  • Huntsman Offline
                    Huntsman
                    Global Moderators
                    Posts: 5,781
                    Huntsman Offline
                    Huntsman
                    Global Moderators
                    wrote on last edited by
                    #7 Quote Reply

                      Beautiful guide Max - Thanks

                      I added it to the modding guides sticky

                      You already have your hacker badge - So I can't give you that again!!

                      1 Reply Last reply
                      • SirVicaLot Offline
                        SirVicaLot
                        Posts: 5,979
                        SirVicaLot Offline
                        SirVicaLot
                        wrote on last edited by
                        #8 Quote Reply

                          Awesome write-up Max! :like:

                          1 Reply Last reply
                          • Max Stone Offline
                            Max Stone
                            Posts: 5,982
                            Max Stone Offline
                            Max Stone
                            wrote on last edited by
                            #9 Quote Reply

                              Thanks Huntsman for the sticky, and thanks Sir Vic :hatsoff:

                              1 Reply Last reply
                              • hiraethus Offline
                                hiraethus
                                Admin Team
                                Posts: 6,969
                                hiraethus Offline
                                hiraethus
                                Admin Team
                                wrote on last edited by
                                #10 Quote Reply

                                  :tu: Good write up. The only thing I could add would be to shape the end of the new rod into a longer point. This will help it to pass through the other tools more easily.

                                  1 Reply Last reply
                                  • Max Stone Offline
                                    Max Stone
                                    Posts: 5,982
                                    Max Stone Offline
                                    Max Stone
                                    wrote on last edited by
                                    #11 Quote Reply

                                      True, I was just worried about a tool pushing its way between the gap of the old and new rod as you push them through the layers, as everything is still under tension, so probably best to not do more than a rounded end... :iagree:

                                      1 Reply Last reply
                                      • jph_777 Offline
                                        jph_777
                                        Posts: 116
                                        jph_777 Offline
                                        jph_777
                                        wrote on last edited by
                                        #12 Quote Reply

                                          Nice tutorial on this swap out, Max. Thanks for the clear explanation and photos! :salute:

                                          1 Reply Last reply
                                          • Max Stone Offline
                                            Max Stone
                                            Posts: 5,982
                                            Max Stone Offline
                                            Max Stone
                                            wrote on last edited by
                                            #13 Quote Reply

                                              Thank you :hatsoff: if only all mods were that easy. :cheers:

                                              1 Reply Last reply
                                              • Jud65 Offline
                                                Jud65
                                                Posts: 418
                                                Jud65 Offline
                                                Jud65
                                                wrote on last edited by
                                                #14 Quote Reply

                                                  After taking a chance based on Max’s instructions I used the same approach to replace the main blade on a 5 layer Woodsman.
                                                  It took a wee bit of fiddling, but I managed to get the new blade into position (everything closed) and tap a new pin in, pushing the old one out. Good snap on all the tools and my Woodsman is restored to its full glory.
                                                  Thanks Max. :salute:

                                                  1 Reply Last reply

                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                  With your input, this post could be even better 💗

                                                  Register Login

                                                  1. Home
                                                  2. Tool Talk
                                                  3. The Mod Squad
                                                  4. How to guide - swapping corkscrew for Phillips
                                                  Reply
                                                  • Reply as topic
                                                  Log in to reply
                                                  COMMUNITY LINKS
                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                  Operational Funds

                                                  Help us keep the Unworkable working!

                                                  Make A Donation
                                                  November Goal: $300.00
                                                  Due Date: Nov 30
                                                  Total Receipts: $0.00
                                                  Below Goal: $300.00
                                                  0% funded
                                                  • Login

                                                  • Don't have an account? Register

                                                  • Login or register to search.
                                                  • First post
                                                    Last post
                                                  0