Multi tool pocket clips
-
@Sos24 said:
I usually carry mine in my pocket organizer which I carry in a cargo pocket. The organizer also has a belt loop for if I wanted to carry it on the belt.
I have tried attaching the Nite Ize HipClip to a couple tools that didn’t have clips. It works pretty well if you want a pocket clip.
Very nice

-
I picked up several pocket hanger clip + micro spring clip from DX.com (Hong Kong) and use them on my pocket carry SAKs & MTs. The micro spring clip lets me swap them on/off to the split rings and the small pocket hanger drops the tool in my right front pocket next to my wallet.
Works great with 91mm sized tools and very discreet.
Here it is with today's carry, LM Micra.

-
The pocket dangler/suspension clips are always a great alternative to regular MT clips
I have several of them and use them on a variety of different EDC items, small lights, SAKs and smaller MTs

-
-
Just wish there was a genuine Gerber multi tool representative that occasionally visited this specific site as I'd respectfully like Gerber to consider the idea of a pocket clip on any of their domestically made multi tools. If their engineers can figure out the machining and tooling information, I'd speculate that adding a pocket clip is possible.
-
You could always DIY. I did :)
Charles.



-
Great!

-
NICE Work CC!

-
Thanks! They're titanium pocket clips for Zero Tolerance knives. About $23-$26 each. Though, I've found a less attractive black pocket clip that is only $10, plus it comes with a knife you can then sell or give away. It mounts the same way. Drill, tap, turn down screw heads to fit through opening, blue locktite. The stainless is tough, so each tap is only good for three or four holes before it's completely buggered. And because it's so difficult to tap through, I have to use larger screws with larger threads, and then turn the heads down. I even have to open up the holes in the clips a little. It's pretty involved, but worth it to make these tools EDC-able.
This is something Gerber should be doing already. With this mod, I can grab my MP600 clipped inside my pocket and flick it open while wearing welding gloves. Usually I move the torch to my left hand, get my MP600, cut off the too-long MIG wire, and put the pliers back in my pocket, all without having to remove my welding gloves. The other alternative is to leave the tool on the welding table, easily accessible, but I find the tool always ends up with spatter (little balls of molten metal) on it, when it's left in an accessible place. This way it stays protected in my pocket until needed. No other tool gives me that accessibility and ease of carry and deployment. Without a pocket clip, I'd be carrying Leatherman or SOG tools, and lamenting having to use two hands to do everything.
Charles.
-
Would be interested in how you made that modification. This would be an awesome addition to any Gerber MP600, Pro Scout and other multi tools I am sure. Kai Industries owns Kershaw and Zero Tolerance, pretty decent knives. Thank you for sharing this information.
If anyone is interested, I found a source for Zero Tolerance titanium pocket clips.
-
Basically I use either 3mm or 4-40 screws. I’ve tried both and the 4-40 is the minimum size that can be used. I prefer 3mm but it is a lot harder to find quality taps in that size. So I’m using 4-40 mostly.
I purchased tungsten carbide tipped micro drill bits from amazon.
These: https://www.amazon.com/gp/aw/d/B00KMDC33W
They are brittle and easily break. So be careful.
First I drill out the holes in the clip.
Then I place the clip on the frame where I want it, And move the tool around on the drill press until the drill is lined up with the hole. Then I clamp it down.I drill the first hole, and then tap it. Use a fresh new Irwin tap. Put the tap in the drill press so it remains square. Nothing on the drill press has moved since drilling, so it’s all still perfectly lined up. Tap by hand until all the way through. Use plenty of cutting lube. Back it out carefully.
Then I take the first screw, clamp the threads in the drill chuck, and then spin the drill press as fast as it will go. I hold a file against the screw to slowly turn the diameter down. I use Allen screws and there is plenty of meat there. This is necessary because the screw heads don’t fit through the hole in the clip.
Once the screw fits through, I mount the clip with one screw. I tighten it pretty good, and get the angle perfect. Then I unclamp the multitool from the drill press base, and line it up again to the second hole. I clamp it again and drill through the frame again. Then I rotate the clip aside, and tap the hole with the tool still clamped. I again use the drill chuck to hold the tap, and turn the chuck by hand to tap the hole.
Now that it’s drilled and tapped, I mount it. The screws protrude on the inside of the frame, so I take a dremel with a reinforced cutting wheel and cut the screws flush with the inside of the frame.
Then I unscrew the screws one last time, add blue locktite, and screw them in tightly. Then wash it, the cutting oil causes the dremeled dust to adhere to everything. Wash it with soap and water, then dry with compressed air.
Note that the tools are never removed, they’re just opened. If the tools are removed the frame isn’t rigid enough to be clamped to the drill press bed.
Charles.
-
Note that if you don’t want to spend the money on the titanium clips, you can search eBay for a “buckshot 8 inch tactical pocket knife with belt clip”
The knife has a clip which fits nicely and is stainless steel plated black, and only cost $10. I remove the clip and resell the knife for $5. Or sometimes I just give it away. It’s a decent blade, actually; but weirdly shaped and nothing special either.
A pic of the buckshot clip is attached below.
Charles.

-
I put clips on everything!

-
And I just saw this on Reddit…
-
@ChopperCharles said:
Note that if you don’t want to spend the money on the titanium clips, you can search eBay for a “buckshot 8 inch tactical pocket knife with belt clip”The knife has a clip which fits nicely and is stainless steel plated black, and only cost $10. I remove the clip and resell the knife for $5. Or sometimes I just give it away. It’s a decent blade, actually; but weirdly shaped and nothing special either.
A pic of the buckshot clip is attached below.
Charles.
Cool looking two tone

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
