What Did You Use Your Multitool For Today?
-
Sharp edges on merchandising cart. Spirit file got this taken care of.
-
Great use of the file OiI

-
Spirit X let me down today. Stupid key broke in the car door lock when I was out doing field rep work. Saw the key there between the keeper doors, and reach in with the pliers and they failed to grab the key. Then tried the awl, lost the key inside. Was able to actuate the lock using the bottle opener flat driver, but that was about it.
Key is inside the locking mechanism. Dipped some thin crafting wire in some silicone sealant in hopes I can push that in between the key and the key hole and pull it out with friction. Am guessing I will end up dismantling the door to get the lock, which is <u>not</u> an easy task. And it's supposed to snow tonight & tomorrow.
Would of been good to have a pair of small needle-nosed pliers right then. :(
Perhaps someone should invent/make an emergency key recovery device/tool that can fit inside a wallet.Watched this video. Now I'll have to black the keeper doors open with something, but if this works, a coping saw blade with a multitool should work. Going to use the Crunch for vice grips though.
- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
Hacksaw blade too high to get in. Need a rasped thin wire probe. :-\
-
Great video

-
Earlier method did not work out so well as the coping saw blade was too tall to fit in the small grooves. So... dug out the Dremel tool and put on a fiberglass cut-off wheel. Reduced the height of the coping saw blade I had on hand, then used the flat side to make more uniform.

Anticipation was getting to me, and had the LED Lenser H7R.2 on the charger from earlier. Nothing more annoying than an intermittently flashing LED light when it is needed. <insert Grr emote>
So this took a few tries, maybe 4 or 5. Used the Crunch to get on the other end and I had to tug, wiggle, and pull. While using needle nosed pliers to keep the key protector open to see what was going on.

Then... PLOINK! Out came the key and fell onto the driveway. That was WAAAAY EASIER than I thought it would be!

And here's the broken key part that broke inside. Brought it indoors cause it was still snowing outside.

Thus, the early morning 'broken in the door' key removal tools. :D

-
Nice work

-
Thanks. Had tried with pins dipped in silicone sealant to friction pull the broken key out to no avail. Was using name tag wires with the ends bent to use as picks, but it got too cold to try. Then was reviewing video I posted again, looked online for other tools, when the idea stuck me to reduce the size of the blade. Did not need that much blade, obviously, and was surprised when the key flew out of the lock! Was so relieved as well. Bedtime now. :D
-
I bet you were well happy when
the key finally come out off the lock
-
@Outback in Idaho said:
Earlier method did not work out so well as the coping saw blade was too tall to fit in the small grooves. So... dug out the Dremel tool and put on a fiberglass cut-off wheel. Reduced the height of the coping saw blade I had on hand, then used the flat side to make more uniform.
Anticipation was getting to me, and had the LED Lenser H7R.2 on the charger from earlier. Nothing more annoying than an intermittently flashing LED light when it is needed. <insert Grr emote>
So this took a few tries, maybe 4 or 5. Used the Crunch to get on the other end and I had to tug, wiggle, and pull. While using needle nosed pliers to keep the key protector open to see what was going on.

Then... PLOINK! Out came the key and fell onto the driveway. That was WAAAAY EASIER than I thought it would be!

And here's the broken key part that broke inside. Brought it indoors cause it was still snowing outside.

Thus, the early morning 'broken in the door' key removal tools. :D

Taking the interior panel off a door is rather easy once you know how, everybody seems to think it's rocket surgery. I would have just taken the lock off the door and fixed the problem on the workbench. Well it is always good to know there is one more way to skin a cat.
Now wrestling a power window regulator in and out that can be awkward, faster with practice, but still awkward. -
Two MT’s saved the morning for our dogs. Namely the Gerber MP400 and the Vic classic.
We went for a walk to the woods. After a while one of the dogs lifted her paw and looked at me. That is her telling me “Human get over here and fix my paw”. Turns out the tip of one of her nails was broken and poked her pads. I guess you could compare that to humans having a small rock in their boot. Not hurtful, but annoying as hell. I grabbed the Gerber and used the wirecutters to clip the torn part. She was pretty happy after :)
Of course we checked and trimmed the rest of her nails when we came home. They were not really long, so not sure why it happened in the first place.

We continued the walk and about five minutes later the other dog stepped into some prickly. With their curly hair, that stuff gets embedded quickly. So I got another look, asking for assistance. I checked the paw and turns out he had two of those prickly things between his pads. MP400 pliers removed these in no time, but a few thorns were being stuck in his pads. Out came the tweezers of the classic and fixed that problem.
Two tools in use, two happy puppies :D
-
I just used the large screw driver and tweezers on my Vic Camper to remove the back plate of my phone and extracted the SIM card.
-
I used the locking caplifter on my Mikov Praktik (basically like a Centurion/Adventurer without anything on the back) to pry off the cover to the flourescent light in my room so I could get the types off the bulbs. Found they were even less than half what Lowe's asked at the electrical supply house ($10 for all four bulbs, vs. $15 for two at Lowe's), but I have to special order them to be shipped to the local warehouse, since they do not carry them in store. Thus, it's gonna be a while.
-
Taking down a curtain rod, and cutting and bending some wire to hang a wreath.
Sent from my iPad using Tapatalk
-
The good
Spoiler:
We spent some amazing time in the woods gathering mushrooms yesterday. I used Work Champ and handed a LM Signal with a brand new never used before factory sharped blade to my lady


Also used scissors to open a new pack of zesty Carpathian herbal tea [emoji478]

The bad
Spoiler:
After cutting a few shrooms the blade on a Work Champ stopped being shaving sharp - fixed really quick today, but to me shrooms are a pretty soft substance that shouldn’t affect sharpness that fast
The ugly
Spoiler:
It was a rainy day, so i just wiped both blades with my sweatshirt and put back in their sheaths.
Today I’ve also discovered some rust stains on a Signal blade [emoji17]
Cleaned easily with Ballistol and a piece of cloth, still I find it pretty disappointing


-
@alexanderre said:
The goodSpoiler:
We spent some amazing time in the woods gathering mushrooms yesterday. I used Work Champ and handed a LM Signal with a brand new never used before factory sharped blade to my lady


Also used scissors to open a new pack of zesty Carpathian herbal tea [emoji478]

The bad
Spoiler:
After cutting a few shrooms the blade on a Work Champ stopped being shaving sharp - fixed really quick today, but to me shrooms are a pretty soft substance that shouldn’t affect sharpness that fast
The ugly
Spoiler:
It was a rainy day, so i just wiped both blades with my sweatshirt and put back in their sheaths.
Today I’ve also discovered some rust stains on a Signal blade [emoji17]
Cleaned easily with Ballistol and a piece of cloth, still I find it pretty disappointing


LMs, especially bead blast models, rust easily because of the high carbon content of the steel (which isn't a bad thing if you ask me). I cleaned my ST300, let it air dry about an hour or two; and then when I came back, there was rust stains all over the tools, the blades especially.
-

@Outback in Idaho said:
Earlier method did not work out so well as the coping saw blade was too tall to fit in the small grooves. So... dug out the Dremel tool and put on a fiberglass cut-off wheel. Reduced the height of the coping saw blade I had on hand, then used the flat side to make more uniform.
Anticipation was getting to me, and had the LED Lenser H7R.2 on the charger from earlier. Nothing more annoying than an intermittently flashing LED light when it is needed. <insert Grr emote>
So this took a few tries, maybe 4 or 5. Used the Crunch to get on the other end and I had to tug, wiggle, and pull. While using needle nosed pliers to keep the key protector open to see what was going on.

Then... PLOINK! Out came the key and fell onto the driveway. That was WAAAAY EASIER than I thought it would be!

And here's the broken key part that broke inside. Brought it indoors cause it was still snowing outside.

Thus, the early morning 'broken in the door' key removal tools. :D

Nice!
-

@ezdog said:
I used the Centerdrive Today to remove the intake wall plate from a Central Vac system in a huge house.
Then I grabbed a non-conductive fish tape and reamed the pipe in the wall for a few hours attempting to dislodge a blockage of some kind.
I closed the connections with the pliers to make the vac turn on with no hose attached to test the reaming?
I then took a Shop Vac to the thing and alternated between sucking with the shop vac and blowing with the central vac trying to move the blockage in either direction even a little bit!
After about 45 minutes of this I was able to grab and extract some kind of furry beast with the CD Pliers thus restoring the inlet to working!!!
I am not a Vac technician.

Hahah
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


