84mm SAK custom
-
Those are some great peens, Max

-
Getting there, patience and practice...

-
@Max Stone said:
Welcome James to
I’ll just comment of the post/pivot question as I’m only doing 93mm mods, but I investigated this too when starting out.
I could not find any 2.2mm off the shelf barrels, and by the time you drill out the tools (which is a real PIA), the effort does not justify the benefit...so I fell back to the tried and tested rod peening. Sure, you can’t break down the SAK once assembled, but it never needs adjustment and is super reliable. Also looks better imo.
But find something that works for you and what you want to do. We look forward to seeing your mods!

Thanks Max. I was actually thinking about the reliability of peened rods when it comes to being out in the field. I personally like the look of screwed together custom SAKs and am afraid of having to disassemble a peened model if I don't fit it together perfectly (tool rub, tension issues, etc). But I'd also hate to have the piece loosen in the field or loose a screw. And you do make peened rods look good

Out of curiosity, why do people recommend brass pivots? I assume brass is easier to peen due to softness. Is HSS impossible to peen?
-
Probably not impossible, but to get the deformation just on the end would be difficult. Also, as the outside frame you are pinning together is Aluminum, already a soft material, it’s best to match the rivet material with something compatible. Brass also has some flex to take up any minor distortion/miss-alignment across the tools, is corrosion resistant and has an inherent lubricating function at the pivot point of the tools.

-
Hi, James! In fact, drilling up to 2.5 is not as difficult as drilling holes up to 3.175 mm, as most do. You need to decide what you want to see on the outside of the scales, if you can carefully rivet and polish the brass rod, then most likely it will be a more suitable solution, so as not to spoil the design, but I yesterday collected my mod on standard scales and 2.5 mm pivots, it looks and works very well, I plan to make some titanium scales for the 84 mm model :)

-
Depending on how many saks you disassemble you can use the middle pins from 91mm knives.
The bit driver is too long to fit, it also uses super thick liners since there is a lot of torque on them. I hadn’t thought of this but I’d love to see it done now.
The standard 84mm saw spring doesn’t have backside tools. However, if you see the tutorial on how to use two 91mm scissor springs To make one on an 84mm. You can do a similar method with 91mm saw springs to use backside tools. Backside tools are the same length on 84mm and 91mm.
Depending on the density of the micarta you can probably thread a pocket clip into it.
Chances are to use pivots you will have to drill them out. Few easier methods, but less precise. The truth of the matter is you will probably never take it apart for cleaning or any maintenance. They’re not always the easiest things to assemble, due to spring tension.
-
James
You’re asking all the right questions all at once. To work the tools with 2.2 holes up to 2.5 is very easy with a solid carbide reamer. Someone here on the forum recommended this and I have used one for several years. Available online from SuperToolinc.com but must use in a drill press as the solid carbide is brittle. You will probably be ok touching up the springs with a small needle file set to allow for the bigger pins if you go the 2.5 mm route.I learned about through-pin preening here on the forums and it’s a really neat “old school” trick that’s not really that hard. Scary but not hard. You could practice on some old red scales drilled through. Enclosed some pix of peened scales, all 84mm.



-
2.2mm diameter (Ø) is very close to metric 4mm² wire gauge Ø (2.26mm/0.089" Ø which is just a hair smaller than AWG 11 gauge Ø of 2.3mm/0.0907"). Searching for 4mm² sometimes locates additional sources. As mentioned elsewhere in the forum, Conrad International sells 2.2mm brass rods and, as of Jan 2020, their price is €2.49 for 500mm; but, Conrad doesn't ship to
USA and it's territories, Canada, China, Russia, Iran nor Kosovo. It's probably possible to use a shipping forwarder.For hollow barrels, that forum thread also suggests searching for "single hole EDM drill electrode" and, sure enough, 2.2mm Ø is available. One Amazon listing shows they cost US$20 (+ $10 S&H) for 20 pieces 300mm each.
-
58mm tools arent thick enough to fit inline in an 84, 91, 93mm frame.


If anyone can think of a way I would love to brainstorm. Custom spring would probably work but I was also thinking maybe you could bolt/rivet/weld an extra piece of metal onto the top of the spring to fill in the space. Not sure

You can put the combo tool on the back tools like /topic/83668 but at that point you wouldnt be able to use the bottle opener so you may as well just use the small tinker phillips.
-
@Jspiggle said:
58mm tools arent thick enough to fit inline in an 84, 91, 93mm frame.

If anyone can think of a way I would love to brainstorm. Custom spring would probably work but I was also thinking maybe you could bolt/rivet/weld an extra piece of metal onto the top of the spring to fill in the space. Not sure

You can put the combo tool on the back tools like /topic/83668 but at that point you wouldnt be able to use the bottle opener so you may as well just use the small tinker phillips.
Thanks for the visual. I had basically arrived there by just taking a closer look at the mechanisms on the few SAKs I have (rambler, small tinker, lumberjack, executive, recruit). If it's possible to drill the hole to 2.2mm without structurally damaging the smaller rambler combo tool, then using a scissors spring ground down might work?
I also make scrap the idea for now and add the tool onto my 74mm executive since the tool sizes look more similar. Has anyone done this?
-
Here's a new thought. Could that 58mm philips combo tool be added in the same type position that the old long file backtool was in? I believe it has its own separate pivot at the end.
-
I would refrain from using 2.2mm pivot barrels and just use solid pins... As they are hollow in construction, even 2.5mm and 3mm barrels are not strong enough to take withstand backspring tension... Unless you make the screws go all the way in and touch each other to fill the void... where the screw ends meet should be in the middle of liner or tool pivot holes...
For using pivot barrels, 1/8 inch or 3.2mm barrels are best as they have thicker walls...
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
