Sharpener Suggestions?
-
I have all kinds of sharpening gadgets and waterstones. But always return to my lansky turnbox for ease of use. I do have a sharpmaker too but prefer the round rods of the lansky to the triangle rods of the sharpmaker.
-
Look no further than the Lansky Turnbox. Reasonably priced, will sharpen all but a really dull blade and easy to use.
-
Ill have to check out Lansky I suppose!
Thanks guys

-
If you have trouble maintaining the proper angle while sharpening, like I do, I would recommend the DMT system with guide aligner or the Lansky system.
-
@Sos24 said:
If you have trouble maintaining the proper angle while sharpening, like I do, I would recommend the DMT system with guide aligner or the Lansky system.I am also not an expert at sharpening, but this is what I use on knives that will just not get sharp. I have the Lansky 5 stone system and it works great. you can adjust the angle, and then the system keeps it there at every stroke. There are several Youtube videos that you can watch to give you guidance.
-
Two hands down for Spyderco Sharpmaker,
I think this sharpening 'system' is meant for some of the more popular brands we see nowadays(inclusive 30-40 deg), and one of the easiest systems to use and achieve consistent result.
Besides, you could even lay the stones side-by-side to mimic a flat stone, and the selection of up to 4 different stones(CBN and ultra fine ceramic are optional to buy) are easy to reprofile and even make every blade shaving sharp.
I like Lansky Turnbox too, but the choice of stone is quite limited and combination 40/50 inclusive angles are not as popular as 30/40 on the Sharpmaker.
Sharpening angle for some of the popular brands nowdays(inclusive), AFAIK:
SAK 30-40
Leatherman 32-40
Spyderco 30
Benchmade 30-35
Kershaw 40
Buck 26-32
CRK 40
Case 20-30
Opinel 40 -
I've been using the Spyderco Tri-Angle Sharpmaker for several years on the same ceramic stones. Sharpens most everything save a few specialty items, but I use the ceramic stones freehand.

-
@comis said:
Two hands down for Spyderco Sharpmaker,I think this sharpening 'system' is meant for some of the more popular brands we see nowadays(inclusive 30-40 deg), and one of the easiest systems to use and achieve consistent result.
Besides, you could even lay the stones side-by-side to mimic a flat stone, and the selection of up to 4 different stones(CBN and ultra fine ceramic are optional to buy) are easy to reprofile and even make every blade shaving sharp.
I like Lansky Turnbox too, but the choice of stone is quite limited and combination 40/50 inclusive angles are not as popular as 30/40 on the Sharpmaker.
Sharpening angle for some of the popular brands nowdays(inclusive), AFAIK:
SAK 30-40
Leatherman 32-40
Spyderco 30
Benchmade 30-35
Kershaw 40
Buck 26-32
CRK 40
Case 20-30
Opinel 40Happen to know the angle of the Spirit's Chisel, and the curved cutter? Still trying to find a way of sharpening the curved cutter. Might have to make something special for that tool.
-
Couple of interesting sites I found.
The Best Knife Sharpeners on Amazon, According to Hyperenthusiastic Reviewers: http://nymag.com/strategist/article/best-knife-sharpener.html
SAK Home - Maintenance: https://www.sakhome.com/361164051
-
@Outback in Idaho said:
Happen to know the angle of the Spirit's Chisel, and the curved cutter? Still trying to find a way of sharpening the curved cutter. Might have to make something special for that tool.Good question, I don't. But for curved cutter, I just use the old trick of painting the edge black with marker and sharpen it free hand with the ceremic stone. For the chisel, I would lay the stone lay on the back of the Sharpmaker and again use the marker trick to make sure I get the edge.
-
Sent an inquiry off to Victorinox, so will post their reply if it's anything good.
Think I found a semi-decent way with a Smith's pocket sharpener, after reading many other sites. Either lightly run the rat tail file on its thicker side slowly back and for a few times. Ceramic sharpener, run the flat side along one side, with the part to be sharpened against the other. And pull down on the sharpening side firmly. Seemed to do a decent job. ~ Could not get the exact position one-handed to take a photo.
-
Also have a look at a standard set of Paper Wheels.
-
Perplexed by Victorinox's reply for wanting to know the angle of the Cable Cutter on the Chisel...
Good morning, and thank you for reaching out to us about your Swiss Tool. I would like to remind you that all of our Swiss Army Knife products have a Lifetime Warranty against manufacturer’s defects. You can simply send your knife into our headquarters in Monroe, CT to be repaired, sharpened, cleaned, and oiled.
Should it be imperative that you sharpen your tool yourself I would recommend nothing other than our "dual knife sharpener" specifically made to sharpen our multi tools. For your convenience I have provided you with the link to purchase this sharpener from our website: http://www.swissarmy.com/us/en/Products/Swiss-Army-Knives/Accessories/Dual-Knife-Sharpener/p/4.3323In order to complete this process of sending your multi tool in for repair, please visit our website to submit a repair request. I have provided you with the link below. Fill out all the necessary information with the online form and simply ship your knife to us.
https://service.swissarmy.com/Please note: There is a 3-week repair turnaround time for all knives as well as a $5 processing and handling fee per knife.
Should you have any further questions please feel free to reach out to me directly.Have a wonderful day.
Not sending a tool in to get cleaned, sharpened, or oiled. Sheesh.

-
Took them a while to get back to me on the chisel angles...
"Both blades are 45° out of the factory - however they can be ground per customer preference based on use. "
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
