Gerber Armbar Owners Club
-
Testing the awl:
Making a pilot hole in a 2x4 is no problem.

Comparison with PX awl. PX hole on top, Armbar on bottom:

Making holes in leather. Thicker leather on the left, thin leather on the right. Armbar holes top row, PX holes low row. Hard to see, but the holes made with the PX are cleaner. It also punched through the leather way easier. The Armbar had a harder time punching through both leather pieces. During that test the awl also collapsed and drew first blood.

-
Bit Holder with Standard T25 bit:


The bit sits deeper in the holder than I expected. You can see that in the second pic. The bit holder is also slightly larger than the bits (original and standard), resulting in some wiggle room. I don't think it is enough to cause issues during use. I assume it is done on purpose to remove the bit with ease. I used the original bit to drive a #6 screw into the aforementioned 2x4. It worked pretty straight forward, I never had the feeling the bit driver was about to collapse. One issue might be the pry bar. At its rest position, the thin edge presses into your hand when holding the tool real tight. It might be worth deploying the pry bar half way to avoid that.
-
My first day impressions in short:
- Decent blade, works as expected
- Bit driver works straight forward, no issues so far
- Awl is pointy, sharp and in desperate need of a means to prevent it from collapsing. Not necessarily a lock, a tight snap like on the PX would be enough.
- Scissors are average. Not enough leverage and they should open wider. They also cannot cut finger nails. At least not mine
I don't like the deployment, because you have to unfold the scissors moving one arm in the closing direction. This means they will collapse, unless you prevent that with your other hand. - Pry bar is working. Nothing fancy
- Hammer function not yet tested
-
Blood!

Great review - a lot of good work outs on the tool.
Again great photos!
-
Thanks Ray

-
@SirVicaLot said:
Testing the awl:Making a pilot hole in a 2x4 is no problem.

Comparison with PX awl. PX hole on top, Armbar on bottom:

Making holes in leather. Thicker leather on the left, thin leather on the right. Armbar holes top row, PX holes low row. Hard to see, but the holes made with the PX are cleaner. It also punched through the leather way easier. The Armbar had a harder time punching through both leather pieces. During that test the awl also collapsed and drew first blood.

Isn't the awl locking?
I think I remember them saying everything but the driver locked. 
@SirVicaLot said:
Bit Holder with Standard T25 bit:

The bit sits deeper in the holder than I expected. You can see that in the second pic. The bit holder is also slightly larger than the bits (original and standard), resulting in some wiggle room. I don't think it is enough to cause issues during use. I assume it is done on purpose to remove the bit with ease. I used the original bit to drive a #6 screw into the aforementioned 2x4. It worked pretty straight forward, I never had the feeling the bit driver was about to collapse. One issue might be the pry bar. At its rest position, the thin edge presses into your hand when holding the tool real tight. It might be worth deploying the pry bar half way to avoid that.
Glad to hear the driver did well.

I assumed as much of the standard bits sitting lower cause of the double sided bit that comes with it, as it looked a bit longer than the standard, 's why I asked.
Thanks for doing the tests and sacrificing body and limb for the sake of us who hadn't had the chance to play with it yet

;)
Once you find a decent Weißbier, let us know how the bottle opener works

-
The only thing that locks is the blade. I had no issue with that, had the other tools at least that „safety snap“ if you know what I mean. Take the Philips on the Explorer for example. It snaps into place with a reassuring sound. If you want to collapse it, you need to overcome a resistance. If you only barely do it, it snaps back into place instead of closing on you.
Same with the awl of the PX. On the Armbar there is no resistance whatsoever. Unless I have a faulty one, I would call that a problem.
Makes sense that the driver had to be deeper because of the double sided bits

I like Becks every now and then, but I also have access to Paulaner :D

-
Thank you very much for your excellent review of your Armbar

I was looking forward to this one.
It appears to have a lot to like, but the "no snap" situation on the tools is a bit concerning.
I assume this goes both ways (open & closed position)?Do you feel the tools could easily open a bit in the pocket?
-
The no snap situation goes both ways, but I don‘t see any potential for unwanted deployment of the tools - yet.
I might make a short video this weekend to illustrate the differences

-
You're blood brothers now!
Thanks for the ongoing review Sir VAL

Its a reminder of the near perfection of the SAK that even modern rivals fail to better it. Except maybe on the driver.
-
@SirVicaLot said:
...Makes sense that the driver had to be deeper because of tlike Becks every now and then, but I also have access to Paulaner :D

Now that's better :D That's actually my poison of choice

-
@SirVicaLot said:
New Tool, New Club :)I figured we can consolidate all information, testing and photos in here. Let's start with the unboxing:



I love the packaging

-
@SirVicaLot said:
My first day impressions in short:- Decent blade, works as expected
- Bit driver works straight forward, no issues so far
- Awl is pointy, sharp and in desperate need of a means to prevent it from collapsing. Not necessarily a lock, a tight snap like on the PX would be enough.
- Scissors are average. Not enough leverage and they should open wider. They also cannot cut finger nails. At least not mine
I don't like the deployment, because you have to unfold the scissors moving one arm in the closing direction. This means they will collapse, unless you prevent that with your other hand. - Pry bar is working. Nothing fancy
- Hammer function not yet tested
That's a bit disappointing indeed.
I was hoping for a more enthusiastic review on the blade and scissors.
Though I'm not sure what to expect from the blade... Maybe I finer edge? Sir Vic, does it deploy easily with one hand?
The scissors seems to have a lot of room for improvement... Spring, angle of opening, sharpness...
Oh well....
I ordered the Armbar Cork, I'll post some initial impressions when I get it.
-
@magentus said:
You're blood brothers now!Thanks for the ongoing review Sir VAL

Its a reminder of the near perfection of the SAK that even modern rivals fail to better it. Except maybe on the driver.
I agree. Vic is making those knives for how long, over a hundred years? They seem to have perfected every little detail and it shows. Both Gerber and LM have a hard time getting anywhere close to that. I still hope they continue to work on their tools, and make improvements as I like the ideas they have.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

