Charge Owners club !
-
fellas ! -
All my Charges...

Sent from my BLA-L09 using Tapatalk
-
@Hood3dvillain said:
All my Charges...
Sent from my BLA-L09 using Tapatalk
Thats a nice collection!

-
-
Thanks Steve
and awesome pic 
-
Thanks !

-
The strangest failure!
Today my Charge+ broke on me, the outer top of the frame on one arm just cracked on both sides while I just squeezed on the pliers. I was simply oiling the pivots and opening closing the tool, I squeezed on it with moderate force, a quiet cracking sound and it was like that.That arm always felt a bit looser, had a weaker detent in open position, so in retrospect I guess the frame was faulty right out of the box, some micro cracks or something. But strange nonetheless.
I contacted the local authorized LM distributor, but it seems I'll have to wait a while, as due to the pandemic, Portland informed them that they do not take tools for repair - nor send anything back -, and here the standard (and BO) Charge+ is currently out of stock, so they're not able to replace it. Out of Charge, out of luck it seems.


-
@Exeter said:
The strangest failure!
Today my Charge+ broke on me, the outer top of the frame on one arm just cracked on both sides while I just squeezed on the pliers. I was simply oiling the pivots and opening closing the tool, I squeezed on it with moderate force, a quiet cracking sound and it was like that.That arm always felt a bit looser, had a weaker detent in open position, so in retrospect I guess the frame was faulty right out of the box, some micro cracks or something. But strange nonetheless.
I contacted the local authorized LM distributor, but it seems I'll have to wait a while, as due to the pandemic, Portland informed them that they do not take tools for repair - nor send anything back -, and here the standard (and BO) Charge+ is currently out of stock, so they're not able to replace it. Out of Charge, out of luck it seems.
Just a couple of better photos, yesterday's pics came out pretty poor.


-
@Exeter said:
Just a couple of better photos, yesterday's pics came out pretty poor.Not sure it is that unusual ... here's one of my early generation Charge TTi. Admittedly, I took down a plaster board wall with it but purely by hand with gloves and a ladder. I'm no hulk so was disappointed that I was stronger than it ... lol ... after all I didn't break. That crack allowed for enough distortion in operation to clearly notice it. Nonetheless my local Leatherman dealer came to the party so the support is respected and great to have as an invisible part of the multitool. Anyway JFI ...

-
Do you think it was a side force on the blade that caused the fracture?

-
@Max Stone said:
Do you think it was a side force on the blade that caused the fracture?
In my case, this was the first of many Charge TTi models I purchased and also second hand. It was used extensively by me for a couple of years. The blade in my tenure got a lot of use but so did the other tools. The last job before noted structural failure was hard going for about two full days and done as a personal challenge. Do I still have TTi models in my inventory? Absolutely yes and they have also been thrashed and survived very well. The damaged TTi was replaced with a second gen model. Was disappointed only because the S30V in my original, which I'd reworked, had the most wicked convex edge and preferred it to the new straight bevel. Here's a pic from noted job ...

-
Bummer on both counts :(
-
@Heywood Floyd said:
In my case, this was the first of many Charge TTi models I purchased and also second hand. It was used extensively by me for a couple of years. The blade in my tenure got a lot of use but so did the other tools. The last job before noted structural failure was hard going for about two full days and done as a personal challenge. Do I still have TTi models in my inventory? Absolutely yes and they have also been thrashed and survived very well. The damaged TTi was replaced with a second gen model. Was disappointed only because the S30V in my original, which I'd reworked, had the most wicked convex edge and preferred it to the new straight bevel. Here's a pic from noted job ...

Hey, I know you! [emoji16]
Keeping the thread on track, here's my Tti being used to help replace rollers on a copier a few days ago.

-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
:o 



