Supertool 300 VX upgrade (Mod badge request too)
-
Clarifying pics :D


-
Nice one

-
I've been thinking of having these done in metal, by Shapeways, but the plastic is a bit compliant and the metal, being much stiffer, would probably fall off on flexing the handles...
-
I think it should be fine as long as
you get some glue that stays flexible
Some silicone sealants are very good
-
Some newer pics...


-
Very nice

-
I know that it's an older one, but what kind of wrench did you used to unscrew the pivot screw on the ST300?
Thanks for the answer. -
@Dutch_Tooler said:
Here then is Part II of the writeup, featuring the making of The Ring and adaptations of a few other items, followed by reassembly of the tools into the serrated-blade side handle. Also, I'm taking the opportunity to reorder the tools in the straight-edge knife handle and to replace the small bit holder with the awl as well as a spacer washer with the previously omitted lanyard ring. Reordering had become necessary following the discovery that the plier head was just rubbing against the can opener - we can't have that, can we?Here goes!
We start by making The Ring, actually a sleeve which fills the space between the (Surge) saw/file blade exchanger pivot hole and the Supertool's pivot. A copper tube of 6mm outside and 4mm inside diameter is drilled and then turned and parted to make it 5.5 mm outside and 4.8 mm inside as well as 3.0 mm long. While turning and parting I keep a 4.7 mm drill bit reversed in the drilled hole as a support, with some oil to reduce friction. The result is shown on the original pivot.



Then I use the sleeve to align the lengths of the saw/file blade exchanger exactly with the original Supertool saw, and clamp the lot with a small vice grip (sweet little thing, that). I do this to get the position exactly right in order to be able to adapt the exchanger's outer profile to that of the original saw. I use a variety of tools to pull this off, as shown below as well: small bench grinder, Dremel with cutting disc or with a barrel grinder, various files and a vice.




The result is shown below. We want the exchanger lo lock as the old saw did.

Some of the files used, plus tweezer and needle:

The exchanger parts look like this (bottom pic compares the profile with the saw and shows the pivot and ring again):


Meanwhile I took the opportunity to make some slight adjustments to the awl (thinned it a bit) and the large screwdriver (made a small pry bar out of it):

This is the assembly order for the serrated-blade handle (oops, the positions of the exchanger and washer in the picture should be reversed, please note):

As already announced, I also reordered the tools in the other handle, as follows:

This is the assembled straight-blade handle (with an oil pen I used and the tweezers):

This the assembled serrated-blade handle with modified Surge blade exchanger fitted:

It turned out that the scissors and awl were in collision. I ground off a bit from the scissors handle tab: problem sorted!

Here the SuperTool 300 VX in its full glory! All tools work, extend, retract and lock as intended.

This concludes the writeup. Many thanks to other forum members from whom I have unashamedly stolen parts of my mod, to wit at least Zoidberg, Toolslinger and Obi1shinobee
as well as all those who gave tips regarding the awl. I have plans for the small screwdriver bit holder, but those are not necessarily part of this mod and will be reported in a new thread whenever ready.Good luck to those that wish to repeat these exploits!
Oh yes - can I have my badge now please?

Hey Dutch_Tooler,
I've done a similar mod to my Supertool and also have the problem with the larger pivot hole of the surge saw-blade-holder.
Unfortunately I can't make an adapter ring myself.
So, do you think you'd be able to make one for me? That'd be awesome.
I'd also be very interested in the tweezer and toothpick holder.
I saw in your profile that you're located in the south of Germany?
I'm from Wiesbaden, pretty much in the center of Germany. [emoji39]Greetings and stay healthy,
Bernd
Gesendet von meinem LYA-L29 mit Tapatalk
-
Hey Bernd, welcome to

Sorry... the machinery I need to make these with is packed away due to lack of space and conversion of other available space to home office use. Pretty much all of my own projects are on hold pending resolution of the situation, apart from those I can carry out outside that is. I'll keep you in mind for the future though!
Cheers
D_T -
@Dutch_Tooler said:
Hey Bernd, welcome to
Sorry... the machinery I need to make these with is packed away due to lack of space and conversion of other available space to home office use. Pretty much all of my own projects are on hold pending resolution of the situation, apart from those I can carry out outside that is. I'll keep you in mind for the future though!
Cheers
D_TNot a problem. I'm more or less confined to my home office as well. [emoji6]
Gesendet von meinem LYA-L29 mit Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
