Workchamp or Workchamp XL owner Club
-
Both XLs are real monsters....
-
They sure look to be pocket fulls.

-
Obichamp from Workchamp XL

/topic/68180
-
ObiChamp is very cool!
-
@FolderBeholder said:
WorkChamp next to WorkChamp XL
That XL... What a monster!

-
:o Obi.
-
@Shuya said:
What have you done to the knife to remove the lock? Asking because I wanted to modify one Outrider aswell for some holiday trips but dropped it.I carefully removed the slide lock side scale, with a thin guitar pick.
I then removed the lock guts--all straight forward.
I filled the hole with a few layers of paper cut to the flat dimensions of area, with a few drops of super glue on each layer.
Near the top, I filled in with more super glue until level more or less.
I sanded down the glue until even with the scale.On my blue-scaled Helmsman, I melted in some blue plastic laundry line near the top, before sealing with super glue.
On my Rucksack, I cut a piece of unglazed ceramic to fit, and sealed it with super glue.
Our laws allow blades up to 10cm, non-locking, no questions asked (unless you are threatening someone). The 111mm Vic line works out well, with the lock removed. As said, I was 60 years old before I even held a locking folder, and I have cut myself far more since buying locking blades. I grew up with a variety of slip-joint pocket knives, up to SwissChamp size. I used the saws and blades quite a bit in making walking sticks. For most uses, the lock is not as critical as many imagine. Heavy or repetitive work, yes, the lock helps. I am not speaking of any "survival" or "tactical" uses of course.
Test the spring before removing the lock! Some models have weak backsprings because of the lock. Hold the slide button in the disengage position, and open and close the blade to check.
For some models, like the WorkChamp, I have both the now-deactivated slide lock, and the new liner lock model. Camping, hiking, home use, etc. the lock is fine. In truth I have never been searched by the police, even with a fixed blade hanging in a sheath from my belt.
-
Ordered a Workchamp this morning.
Can’t wait for it to arrive [emoji2311] -
mine as following~

-
Awesome collection!
How about giving them a good go in a 30-day challenge I’m planning here for May:
-
If I could, the Work Champ is an excellent tool. Has most of what one needs. The XL on the other hand has a lot of tools which may never get used, like the hoof tool or the gutting blade. As one with an assortment of large SAK's I try to stay with units which have some daily use, and not just excess tools which make the thing "larger" -- but add to it's usefulness.
Personally the Work Champ XL is just a bridge too far, in my opinion, YMMV.....// AND yes I have a Work Champ in my arsenal of SAK's.
The Aerojet
-
@aerojet said:
If I could, the Work Champ is an excellent tool. Has most of what one needs. The XL on the other hand has a lot of tools which may never get used, like the hoof tool or the gutting blade. As one with an assortment of large SAK's I try to stay with units which have some daily use, and not just excess tools which make the thing "larger" -- but add to it's usefulness.Personally the Work Champ XL is just a bridge too far, in my opinion, YMMV.....// AND yes I have a Work Champ in my arsenal of SAK's.
The Aerojet
+1 on that XL is waaaay more than I’d need on a daily basis. Regular Work Champ seems to be a perfect EDC friend for me so far [emoji1316]
But we are just at the beginning of our journey [emoji56]
-
Advanced Notice: I'll be joining in here after Christmas, as I just happen to know what Mrs. EMarkM and her little girl are getting for me... ;)
-

Looking forward to it!
-
I might as well join in...

I've had the slide lock Work Champ since 1999. I will admit to not really looking after it as I should have done over the years, so recently I bought the liner lock model to give the old girl a rest. One of these days I'll clean it up and give it a good sharpen, but for now, the newbie does the job on the occasions it's required. Although it won't see much outdoor action these days due to work/knife regs, so it's stuck with doing the odd job around the house. Still, after all this time, I couldn't be without one and 91mm SAKs seems very strange and small to handle to me.
-
@MichaelGT83 said:
I might as well join in...
I've had the slide lock Work Champ since 1999. I will admit to not really looking after it as I should have done over the years, so recently I bought the liner lock model to give the old girl a rest. One of these days I'll clean it up and give it a good sharpen, but for now, the newbie does the job on the occasions it's required. Although it won't see much outdoor action these days due to work/knife regs, so it's stuck with doing the odd job around the house. Still, after all this time, I couldn't be without one and 91mm SAKs seems very strange and small to handle to me.
Same as other posts, here's what you should have seen. :D
I really should go and do some work, now...

-
I sold my Workchamp years ago. But a while back I got one in a large batch of SAKs. I had forgotten how nice these are :)
This one is in fairly good condition. Mechanickal would probably complain about the large number of fingerprints on it

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
