Leatherman OHT mod
-
are the pivot size the same. Taken apart a OHT before but couldn't quite remember. OHT is in serious need for an update. If they didn't just put in the cartoonish tool for the sake of tradition.. -
Think they are two different sizes Sam, guessing 1/8 and 3/16.
-
I'm not sure I understand the remarks about pivot size, so just to clarify: as you know, the OHT has two pivot sizes. The short tools on the plier side are very close to 3mm, so 1/8" is my best guess. The long tools opposite the pliers use the same size as the Surge.
-
@ComboTool said:
I'm not sure I understand the remarks about pivot size, so just to clarify: as you know, the OHT has two pivot sizes. The short tools on the plier side are very close to 3mm, so 1/8" is my best guess. The long tools opposite the pliers use the same size as the Surge.Ya. Thats what I meant. So far I know that the tools and the pivot screw are all of different size. How did you correct the differences? Any issues with the locking of the implements? Vertical play etc. Me too would like a blade exchanger in an OHT. :)
-
Great looking mod and more what the OHT could/should be if LM chose for it to be

-
@Sam Lim said:
How did you correct the differences? Any issues with the locking of the implements? Vertical play etc. Me too would like a blade exchanger in an OHT. :)No adjustment was required for the pivot diameter or the part that rests against the frame (not sure how it's called). The tool has to be ground off in two places: the rounded part on the top (doesn't have to be very precise, just to make it fit in the smaller OHT frame) and the locking surface at the back (this requires a lot of trials). For the blade exchanger, only the center part has to be modified. I lined up a Surge tool and an OHT tool on the same pivot to mark the differences, and removed the excess with a rotary tool, first with a red cutting disc and then a grinding stone for the final adjustments. The tools lock properly with no play.
The Surge tools are slightly thicker, so in theory you may want to use a longer pivot, I had no problem no problem reusing the original OHT pivots (overall the tool is about 0.5 mm thicker now than the original OHT).
Hope this helps.
Here are a few pictures to show where to grind (the bare metal shows) and the locking of the tool. -
thanks for the explanations! 👍 -
Posting this made me want to finish the awl mod, and I'm happy to report a success. As I said earlier, because the awl isn't designed to work with a liner lock (it's one of the inside tools on the Surge), there is a flat surface at the bottom. When opening the awl in the OHT, there's nothing to keep the liner lock depressed, so it engages about mid-way. To solve this, I have added a bronze washer to the awl, which I punched to prevent rotation (there is an indent in the awl for the original locking mechanism). Now the awl opens in one motion without needing the other hand to keep the lock depressed.
-
While I was at it, I decided to add back the small flathead. It folds above the scissors without protruding. Of course, it has to be open when deploying the scissors, but those scissors are quite cumbersome to open anyway, so this doesn't add much complication.
-
So here's the final tool selection. While it was apart I noticed that contrary to what I wrote earlier, the pivot hole of the OHT tools is slightly narrower than on the Surge tools. The difference is minimal (I hadn't noticed it before), and it hasn't caused any problem.
-
Excellent work

That is the way the OHT should be like
-
That is a much better layout than stock :o

-
The saw is longer now too. :D
One of the things I like is the tools look like they were always there.I don't know if I could give up the serrated blade though as it's my most-used tool.

-
The scissors have to go in a left-hand slot (replacing either the saw or the serrated blade of the OHT), but the blade exchanger can probably be made to work in a right-hand position, so a configuration that retains the serrated blade is possible.
-
Wow
-
Welcome to
Robbin 
-
I've been revisiting my OHT mod, this time I've added a Surge bit holder and Metro's utility knife holder for Signal. The only original tool remaining is the large flathead (I keep it despite the bit holder for light prying). I guess it's the final evolution of my OHT project.
It all started as a "could I do this?" project and now it's a tool I could actually use... if only it wasn't so big and heavy
-
Now that's a OHT I can get along with! Great mods!

-
Very well done.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

