Gerber Mp600 owners club ;)
-
@Juan el Boricua said:
Good day to everyone at MT.O, and your family; hope all are safe and sound.
For today, it's my SS NN MP600 and its kit, still using my replacement C-clip from this post: /topic/84221
So far so good ...
Hey Juan, can you tell me more about your Accessoires? I'm interested in your jigsaw blade. How do you make them fit? [emoji848]
Greetings, Seb[emoji869]
Gesendet von meinem SM-A600FN mit Tapatalk
-
Hello MTS; the jigsaw blades are standard u shank/"universal blades. The serrated edge "knife", was made by measuring the SE blade from my MP600 Basic, transferring and adjusting that measurement to an old steak knife (think Longhorn's/Applebee's/Outback's in the States) andthen tracing the shank onto what will be the tang. Drill hole with tungsten bit, finish off with diamond round bit, and then cut shape with cutting disc ( I used regular; may use reinforced one). Finish by polishing cuts with sharpening stone/sandpaper cuts.
The "awl bit", was made following a post from here. At the moment, I'm busy but later on I'll look for the link ( it's something like "awl bit for wave/charge"). Hope this helps; enjoy!
-
Here's the link for the awl bit:
/post/12587
Have fun!

-
Looking back, sorry that maybe I misunderstood you!

If you're talking about the jigsaw blades from the SS Mp's kit, those are t shanked blades. I ground the nubs off, measure carefully for shortening it and marking where it will ride (another alternative would be to remove one of the tools and trace shape); using a 1/4" cylindrical grinding stone (again on the Dremel) I ground out "the hook". This is so that it fits over the female pivot post, between handle and can opener. Mind you, not all blades have the neccessary width and, will not fully lock ( it will not close on you during use because it rides against the chassis/handle like a regular tool and there is some resistance if you try to fold it in without operating the sliding lock). If you have any other questions or inquiries let me know. Hope that this now helps!

-
@Juan el Boricua said:
Looking back, sorry that maybe I misunderstood you!
If you're talking about the jigsaw blades from the SS Mp's kit, those are t shanked blades. I ground the nubs off, measure carefully for shortening it and marking where it will ride (another alternative would be to remove one of the tools and trace shape); using a 1/4" cylindrical grinding stone (again on the Dremel) I ground out "the hook". This is so that it fits over the female pivot post, between handle and can opener. Mind you, not all blades have the neccessary width and, will not fully lock ( it will not close on you during use because it rides against the chassis/handle like a regular tool and there is some resistance if you try to fold it in without operating the sliding lock). If you have any other questions or inquiries let me know. Hope that this now helps!

Hey, thanks for your answers! Your knife mod in a bladeless is cool! I spontaneously come up with an idea. You could make a fork and a spoon to fit into the tool holder[emoji108][emoji848] that would be perfect for camping!
That with the hook is a good idea! I only get the T shaft blades here in Germany. That's why I filed them thinner and thinner so that they fit [emoji28]
I will put the Awl bit on the ToDo list. [emoji108][emoji123]Gesendet von meinem SM-A600FN mit Tapatalk
-
I’m still loving my modified MP600. I have other gerber tools and other mp600s, but I always come back to this as my heavy duty workhorse tool. I originally made it with leftover parts from junk tools. It’s got quite a few diesel parts in there, including the scissors, large flat driver, saw, and bottle opener.
The plier heads have been ground so they fit completely in the handles. I ground a scraper into the end of the file. I drilled and tapped holes for a pocket clip. The latest mod was expensive - I searched high and low for an mp600 with an awl. Found one and swapped it in. Now it’s the perfect tool for me.
Charles.

-
Good work CC

I was looking at the clearance behind the pliers when closed, and I recon that there’s a bit of space left to have the pliers slide in a little deeper. I may look at extending the slide slots to see... -
I did that too. Just a quick hit with a dremel and I got an extra 2mm of space to slide them in further.
Charles.
-
Nice mods um the MP600 CC!
Great tool
Enviado de meu moto g(6) usando o Tapatalk
-
> @ChopperCharles [said](/post/2121469): > I did that too. :t~~u: > ~~ > Charles. Not this... Nice and clever mod, thanks! -
@ChopperCharles said:
I did that too. **Just a quick hit with a dremel and I got an extra 2mm of space to slide them in further. **Charles.
...this!
-
For today, its my Gerber Duo. My "bladed" bladeless helped me make an ikebana for my Mom; hope she likes it!
Happy Sunday/Mother's Day!



-
Very nice duo Juan!
And beautifull flowers
Enviado de meu moto g(6) usando o Tapatalk
-
@ChopperCharles said:
I did that too. Just a quick hit with a dremel and I got an extra 2mm of space to slide them in further.Charles.
I measured and cut the slots back 3mm with my Dremel. The blunt nose MP600 pliers now retract fully. Much better.





-
Nice mod there, Max!

-
Thanks Juan.

Now they match...





-
Nice, very nice.

-
Really nice [emoji108][emoji869][emoji482]
Gesendet von meinem SM-A600FN mit Tapatalk
-
Thanks guys.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login