Gerber Armbar Owners Club
-
I wonder if the original prototypes had a good detent on the tools, and something for smurfed up in scaling production, or if Gerber really just didn't give a smurf.
Also, I can't be too hard on them. Leatherman apparently never bothered squeezing the pliers on their $140 multitools.
Max Stone put it perfectly. "My interest had evaporated".
-

QC down across the board.
-
I dunno guys. I have like seven MP600s and MP400s, a Diesel, an NXT, and an original suspension, and not a single pair of those scissors can cut paracord. Every victorinox 91mm I have can, even the used and abused knives. The only Gerber tool I have that can cut paracord in one snip is the teeny little knife with slide-out jewelers drivers and a slide-out knife. Keystyle maybe? That one can cut it in one snip, but it takes enough pressure that my thumb hurts. They are Fiskars branded scissors in that tool. None of the rest are. But the design is the same, so I don't get it. How hard is it to make good scissors? Victorinox did it. Wenger did it. Gerber did it once at least.
Charles.
-
@ChopperCharles said:
I dunno guys. I have like seven MP600s and MP400s, a Diesel, an NXT, and an original suspension, and not a single pair of those scissors can cut paracord. Every victorinox 91mm I have can, even the used and abused knives. The only Gerber tool I have that can cut paracord in one snip is the teeny little knife with slide-out jewelers drivers and a slide-out knife. Keystyle maybe? That one can cut it in one snip, but it takes enough pressure that my thumb hurts. They are Fiskars branded scissors in that tool. None of the rest are. But the design is the same, so I don't get it. How hard is it to make good scissors? Victorinox did it. Wenger did it. Gerber did it once at least.Charles.
I don't know either - I wonder why Fiskars scissors aren't so good here.
Do you have the Splice... is that just as unimpressive? -
Well, maybe I solved it a little. The keystyle scissors drag against each other significantly the whole way through the scissor stroke. None of the MP600 scissors do. If I hold the keystyle scissors up to a strong light, and have the scissors closed with my thumb, I cannot see light between the blades. For every other gerber scissor, I can see light between the blades.
So for smurfs and giggles, I got out a cheapie multitool with the same kind of scissors, which look like MP600 scissors, and actually cut just a hair better. And I put them in a vise, holding the scissors at the pivot. Then I tapped the blades with the flat side of a ball-peen hammer. I tapped them such that the blades would press against each other as the scissors cut.
And.... it worked. Sorta. I tapped too much, and initially the scissors would snag in the closed position. But after working them for about 5 minutes they wore down or loosened up, and now those same scissors can cut paracord. It still takes some force, but they work significantly better now. I tried it on a $10 multitool first... and was pleased. So then I tried the same thing on one of my favorite tools, which also happens to have some of the worst scissors. The Ruike LD51. And it worked there too! I had to be a lot more careful with the Ruike, because the backspring action on the scissors is pretty weak. But those scissors can cut paracord in one snip now. Before this they just bent the paracord between the blades.
Basically, it's cheap and easy to make straight scissor blades. But to machine or bend in a slight curve to the blades, which is just enough to make for super precise scissors but not enough to overcome the force of the spring with drag, is I'm guessing a lot more difficult or expensive to do on a mass-production scale.
But then again, Victorinox has it down.
Charles.
-
Hey Charles, your observation and fix is great.
I do the same on my full-size kitchen Scissors. I bend the blades into a slight curve so they bite a little better and and a quick run on a belt sander, even worn scissors cut tissue paper all the way along the edge. 
-
So, after rigorous testing, the Ruike scissors no longer cut in one snip. They still cut better than before by far, but once they loosened up enough so the backspring had pressure to open the scissors reliably, they no longer cut paracord reliably. Still better than before.
The Gerber style still cut paracord. I just cut a 2 foot section into 1/4" long bits, over and over and over again, and except for a sore thumb they worked great. I'm going to try this on some actual Gerber scissors next.
Also, I found the perfect Gerber pocket knife, which is not made by Gerber. I'm waiting on its sister to arrive, and then I'll post more information.
Charles.
-
@ChopperCharles said:
So, after rigorous testing, the Ruike scissors no longer cut in one snip. They still cut better than before by far, but once they loosened up enough so the backspring had pressure to open the scissors reliably, they no longer cut paracord reliably. Still better than before.The Gerber style still cut paracord. I just cut a 2 foot section into 1/4" long bits, over and over and over again, and except for a sore thumb they worked great. I'm going to try this on some actual Gerber scissors next.
Also, I found the perfect Gerber pocket knife, which is not made by Gerber. I'm waiting on its sister to arrive, and then I'll post more information.
Charles.

:D :D
-
Okay, okay. There are two different versions of these little tools. One is labeled Bibury, the other PowerDelux. Amazon links:
https://www.amazon.com/gp/product/B082HNVJTB/
https://www.amazon.com/gp/product/B07Z4DBFXN
These use Gerber tools. Any tool from a Suspension, NXT, MP400, MP600, etc fits.
The tool is a little shorter than a Wenger SAK, measuring at 75mm. It's about the same thickness as a 4 layer Wenger The scissors are slightly better than any of the scissors in my suspensions or MP400s. Yes. Better. The blade is shorter than the blade in an NXT, though an NXT blade will fit if you remove the lanyard ring and replace it with a bushing. (It contacts the ring). The blade is tanto, but does not have the forward edge profiled or sharpened. So it's not useful for stabbing. It is however quite sharp, goes through receipt paper easily. The quality of all the implements is damn good. Not quite Gerber quality on the machining of tips and edges, but still very high. For instance, the can opener blade isn't as sharp or as large, and the screwdriver tip isn't as well defined as on the NXT. But the NXT part will swap right in if you have a broken or a spare. The phillips driver actually slots deeply into more screws than the Suspension's driver does, and fits securely in more screws around my house. The Suspension's 2.5D driver is thicker and more robust, but it doesn't fit half the screws in my house.
Basically, any tool you'd want to mod into this is mostly feasible. Any of the suspension or NXT inner tools fit (basically anything except the blade or saw). Any of the short MP600 tools fit. Longer MP600 tools, such as the file, will have to be cut shorter to fit.
The tool uses medium thickness washers. Going to the thin washers looks like it will fit a whole additional tool in there. It's a modder's dream, to be honest. I've always loved the MP600 locking tools, and had the thought of cutting and modifiying a handle to be a little pocket knife. This tool does that, with style and class. I talk about modding it, which is my thing, but the tools that come in it are perfectly adequate as they are. The blade is sharp, the scissors cut better than my MP600 or NXT, (even before my tweaking) the file files, the screwdriver screws. The only bad point is the line cutter on mine was so dull it couldn't cut anything. But 10 minutes with a diamond file fixed that.I am waiting on the version above with the saw. The line cutter isn't really a useful tool for me, but even a short saw is useful. Especially since I tend to use it on plastic more than anything else.
I really need to reiterate, if you like the tools in the Suspension, you'll love this. It takes all those tools and puts it in a very compact, tiny, USEFUL tool that fits in your coin pocket. The back is even perfectly flat, and perfectly sized for a Nite Ize clip to stick on.
Charles.
-
Interesting. Are all tools on it locking? In that case it would be better than the Armbar

-
Yes, all the tools lock, just like the Suspension, NXT, and MP600. It's my new favorite EDC. It's so tiny, but so useful. I'm going to buy a slew of them for stocking stuffers for my friends and family and work team. And of course, I'm going to buy a couple to keep stock and a couple to mod :)
Charles.
-
Ooh, can I join now?

-
I just picked up a Gerber Fit. I really like this thing! It's a rather large pocket knife with an LED flashlight (which runs on a triple-a battery thankfully), and it has a locking bit driver, a blade, and scissors. Plus two micro drivers and tweezers. Dunno why it didn't catch on, other than perhaps the bulk, but I like it. I think a nite ize clip will make it rather perfect.
Charles.

-
@ChopperCharles said:
Okay, okay. There are two different versions of these little tools. One is labeled Bibury, the other PowerDelux. Amazon links:https://www.amazon.com/gp/product/B082HNVJTB/
https://www.amazon.com/gp/product/B07Z4DBFXN
Nice find Charles! .7 inches deep is a bit much for my pocket. Can you offer an opinion on how easy it would be to drop a layer or two to slim it down? And maybe a picture of the backspacing.

-
To make it thinner, you'd have to cut the plastic back and shorten the pivots. That doesn't really seem doable without a milling machine. This tool is a hair thicker than a 3-layer Wenger SAK, if you don't count the pivot screw heads. It's not as wide or as long as a Wenger SAK though. It's really a lot smaller than you think. I've attached some comparison photos with a Wenger and Victorinox SAK.
Charles.




-
Thanks Charles. Appreciate it.
-
Why is the price of the Armbar going up?

it's gone from $31 to $41 on Amazon, and almost as much on the Gerber site, ???
-
Not a big fan of this tool to be honest. No locking other than the knife (liner lock works great here). The scissors has this little nub that should have been expanded for ease and comfort of use. My thumb started feeling the pressure of that minuscule curved piece of metal that interfaces with you. My copy appears to cut ok...but the puny little spring is more than useless as my copy appears to be somewhat tight and does't do a good job of springing the two scissor blades apart. I do like the driver however, and the awl is cute and I suppose effective. The bottle opener on the end appears to have the best tactility of the whole tool set. I still cannot phantom why the other tools do not lock, or even snap into place. It is like working with a wet spaghetti noddle.I tried using the driver and it functions good...but wants to always rotate on you simply because there is no snap or locking mechanism. At least you can angle the handle whichever degree you want to get some effective torque I guess.
-
Thanks for your observations, they basically mirror my thoughts. I guess the no-snap on those tools is really intended. I guess I will never understand the thought process behind this decision

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

