What did you use your Sak on today?
-
Great use and idea ulzhan

-
thx ElevenBlade, Kranken & Wspeed
got a new alox minichamp which I currently carry as EDC. Very useful for its small package.
-
I wanted to bake Nutella brownies but my sister absconded with our baking trays at the beginning of lock down, enter the Explorer and some non trivial amounts of foil...

It worked pretty well!

-
Nice

-
-
Used the pioneer awl to drill a hole in the bottom of a trashcan to make it easier to take the bag out
-
Great uses everyone [emoji1316]
Frankly speaking, I hoped for this to arrive during my 30-day Work Champ challenge, but it didn’t. So I’ll post it now.
A few weeks after hours of watching and listening to different reviews I pulled a trigger on a new set of noiseless pickups for my Fender American Standard Telecaster. I went with Seymour Duncan Vintage Stack set if you’re interested, hoping they will give me that spark single coils deliver but without all the additional hum.
And so as they arrived I went on to install them using the Work Champ [emoji1305]
For those interested details are below, for everyone else here’s the final pic

Spoiler:
First of all a large Phillips was used a lot to unscrew all the parts

Then the guide says you need to twist and solder and tape red and white wires, so I used scissors to cut the thermal isolating tube

Installation time - lots of screwing again of course and even pliers to pull the wires from all those hard to reach places

Small Phillips was used as well on some screws so it’s definitely a nice to have

And scissors again to cut open a new set of strings

Conclusion: I definitely received what I was after and sound wise I can tell it’s an upgrade for sure. Though the set I got on eBay marked as open box and again it was all mess - box was damaged and neck pickup had totally wrong set of screws with it that are slimmer then the holes on it, so I had to improvise with mounting it [emoji2371]
-
@alexanderre said:
Great uses everyone [emoji1316]Frankly speaking, I hoped for this to arrive during my 30-day Work Champ challenge, but it didn’t. So I’ll post it now.
A few weeks after hours of watching and listening to different reviews I pulled a trigger on a new set of noiseless pickups for my Fender American Standard Telecaster. I went with Seymour Duncan Vintage Stack set if you’re interested, hoping they will give me that spark single coils deliver but without all the additional hum.
And so as they arrived I went on to install them using the Work Champ [emoji1305]
For those interested details are below, for everyone else here’s the final pic

Spoiler:
First of all a large Phillips was used a lot to unscrew all the parts

Then the guide says you need to twist and solder and tape red and white wires, so I used scissors to cut the thermal isolating tube

Installation time - lots of screwing again of course and even pliers to pull the wires from all those hard to reach places

Small Phillips was used as well on some screws so it’s definitely a nice to have

And scissors again to cut open a new set of strings

Conclusion: I definitely received what I was after and sound wise I can tell it’s an upgrade for sure. Though the set I got on eBay marked as open box and again it was all mess - box was damaged and neck pickup had totally wrong set of screws with it that are slimmer then the holes on it, so I had to improvise with mounting it [emoji2371]
Nice tele[emoji106] and SAK of course.
Well done on the coil mod tooSent from my iPhone using Tapatalk
-
Just a little kitchen duty this morning.



-
Day two of the mediocre British Bake Alone saw the Explorer cutting more baking paper and pulling the wire tray out of the oven (you guys are right, the hook is great at that).
-
Used my Pioneer awl to cut a thread off my wifes new jersey as the main blade needs a touch up after cutting under floor heating fibreglass mats all friday. Used the flat SD to scrape some labels of a glass jar for washing and reusing
-
Great uses everyone

-
My boss put his foot through a plastic pallet this afternoon and got stuck there, couldn't get his foot out at all.
Fortunately I was nearby, with a Swiss Army knife right at hand! I pulled my Trailmaster from my pocket, opened the saw, and had him free in a trice.

I should have told him I had to amputate his foot... ah well, another day.
-
Hope for this to be done during the challenge as well, but the parts arrived late.
The lights on the kitchen smoke exhaust got broken and they really help sometimes when cooking in the evening.
I found the replacement parts on AliExpress for like 10-15 bucks for a set of two, but then I disassembled them, found that they consist of simple white LEDs and ordered 200 of those for about 3$ [emoji2371]
Today I decided to get it done, so used Work Champ to first unscrew the enclosure

As I disassembled those lights previously I found the broken LEDs using a multimeter and marked with a black marker so they’d be easier to find and replace
As I attempted to remove the broken ones it turned out that pliers would be of much help pulling LEDs out of the board


Little by little all 5 broken LEDs were replaced and the smoke exhaust shines like a Christmas tree [emoji319]

-
Nice job alexanderre

-
Nice job, both of you

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login