Schrade Tough Chip
-
While the blades on your ST2 might be too loose, the problem of blades pulling apart is one reason there are lefty and righty scissors to begin with. A right handed person closing right handed scissors will tend to force the blades together and cut efficiently due to the orientation of the thumb, even if the pivot is sloppy enough that the edges can be separated manually as they close. Like occurs on many of my Micra scissors. And several pair of good old fashioned full size scissors.
-
@shecky said:
While the blades on your ST2 might be too loose, the problem of blades pulling apart is one reason there are lefty and righty scissors to begin with.I don't know how to say this nicely, so I'll just SAY it.
First, I'm left handed. There is really, seriously nothing you could explain to me about lefty-righty scissors that I don't know and live with every pair of scissors ever.
That is NOT the issue with these scissors. They are not solidly held together. They are not peened, and they are not screwed. They're held together with spring tension, and it does not matter one iota which hand you use to operate them, it is solely and ONLY spring tension holding those two blades together. The tests I did with them, where they performed abysmally, were all done left handed. And for ALL of my scissor tests, if a scissor seems ot be performing poorly, I'll try them right handed (Many of the results for my scissor test thread rate differently for left or right handed use).
Without using them for cutting, you can push the two blades apart, at the hinge, a small amount, and when you let go, the spring pushes them back together.
I'm not trying to start a fight or sound inflammatory, I just actually know what I'm talking about, and it's not a left/right issue.
-
I wasn't trying to start a fight, which is why I qualified my responses by saying "the scissors might tend to exhibit that particular problem", and "While the blades on your ST2 might be too loose". I do stand my characterization over the issue that pops up with the ST2.
It sounds as though your particular example is particularly faulty, as of the several I obtained in a group buy do not exhibit an unusually sloppy pivot. They're all quite solidly and consistently riveted construction, perhaps the most redeeming quality of the examples of the ST2 I own.
-
Yeah, I think my previous post came out sounding a lot more sour than i intended. Sorry about that.
-
Yay thread resurrection!
Sooooo, I got tired of my Tough chip not being tough, or cutting much of anything. And I thought I'd fix that.
First, lets see how bad they are:
Yowza, that's a lot of blade separation with not a lot of force. Looking at it, there is some blade bending, but most of it seems to be the pivot. I tried peening the pivot tighter to no avail. So.... lets go to the shop. First I'll drill out the rivet
And then separate the tool out into its components.
Looking at the pic, what you see is the rivet, the pivot, a spring washer, the two scissors, a flange for the spring, the spring, and the spring cover. The problem with the tool is the pivot (second piece from top) is too long and contacts the bottom of the flange (third piece from bottom). It can never be a tight pivot because no matter how much you peen it, the pivot is a fixed length and no more pressure can be applied.
Charles.



-
So what do? Well first, I want to put a screw pivot in this thing. I have one that is almost the right size, but it's too big by just a hair. That hair happens to be a standard drill bit size. So... to the Lathe!
First, I drilled out both the pivot and the flange with the lathe. Easy peasy, just remember this is stainless so use a lot of cutting oil and a really sharp bit, at a relatively slow speed. This drill only removed about 2 thousandths.
Then, I drilled out the spring cover so it can center on the new larger pin.
Finally, I took a file to the pivot and reduced the height. This way it will sit slightly below the top of the two scissors when everything is assembled. This will allow the parts to be sandwhiched together. Here you can see it sticking up slightly, as the spring washer is not in place as I'm filing.
Not shown is me also filing the new threaded pin (which replaces the rivet) to length as well.
Charles.



-
And here it is all assembled. I don't know what the new threaded pivot pin is from, it might be a multimaster, it might be some cheap generic kobalt tool, I don't have a clue. It was just in my parts bin. The screw looks like a multimaster screw, though. (especially because it's soft as cheese)
So... how did this do? Well... better. But still not perfect.
The pivot is definitely tighter, but the scissors still bend paracord instead of cutting it. The pivot still has some play. I think the ultimate solution is to remove the spring washer entirely, and file the pivot height down even more to compensate for that missing part.
That will be part 2.
Charles.


-
If only they had half the dedication you have. Excellent work!

I do not have one of these. I like multi-tool scissors, and it seems I am not missing out on much with this.
-
I have this, the Leatherman Micra, and the cheapie Craftsman scissors you can get in every Ace Hardware from here to the moon for ten bucks. And.... the cheapie craftsman has the best scissors of the lot. As far as mini tools go, that's the winner by far. The rest of the tools in the craftsman are shiatty, but the scissors are great.
Well, the phillips driver is passable. The other drivers and tools can be made better with a quick trip to the disc sander and finishing files. That gives the drivers nice sharp, non-rounded edges and the awl and can opener cutting surfaces. Still pretty smurfy, but usable in a pinch.
I have yet to try the SOG CrossCut, but for $20 I will probably snag it soon.
Charles.
Charles.
-
Update: I removed the spring washer and filed everything down a dash more. And sadly, these scissors will just never cut paracord. Even with the pivot so tight that the scissors can barely move, they cannot cut it. At this point it’s no longer the pivot flexing, it’s the blades themselves. They are just not beefy enough, and they bend too easily.
That said, removing the spring washer does make a significant difference. There was a particular piece of glossy cardboard that these scissors would consistently bend, and now they cut it every time. So they’re far better than before... but still not great. Perhaps now on par with the Micra scissors.
Charles.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login