What's your latest SAK?
-
A week well spent. Brand new scales on half a dozen online purchases - An old Swiss Champ (no hook, no pin) restored to its former glory in original red; 2 Minichamps & 2 Huntsmen in matching yellow and green, a random Spartan now in white. Finally, a virtually NIB Executive - long desired and finally acquired. Yes, that’s been a good week...

-
Nice ones Jud

-
Thanks lads. This week just keeps on giving: my sister in law’s partner, a pilot, knows about my predilection for a bit of Swiss sharp and presented me with this beauty today, out of the blue. A Forester in walnut - promo merchandise for Pilatus aircraft.

-
And so..... Here they are...!!

A user one and backup, properly disinfected and drying up...
The Pox is getting worse by the minute...


-
Nice ones MacGyver

-
Thank's mate

I'm biting myself trying "not to order" the red and blue ones from https://www.schweizermesser-shop.de/ But i'll probably loose that battle...

Every time i see pics of your X's lately i just go....
I definitively got a strong case of Pox

-
Hey MacGyver you just bought a one way ticket. Welcome to the club. :D
-
I'm biting myself trying "not to order" the red and blue ones from https://www.schweizermesser-shop.de/ But i'll probably loose that battle...

Every time i see pics of your X's lately i just go....
I definitively got a strong case of Pox

I managed to resist, so far, saying I'm waiting for my usual shop to have the Farmer X.

Must start thinking about a new excuse for when it arrives...

-
Aitor 90mm 'Waiter'.
The plan was to cannibalise the combo-tool, but it's too nice to pull apart.

-
Some lovely new additions to collections here!
I found a PX going cheap, so finally bit the bullet and had a go at some modifying of 93mm knives. First I dismantled the PX with silver scales, centre punching then grinding/drilling the rivet heads off with my Dremel without damaging the alox scales - seemed to work well at the first attempt. Next I did the same to a SE Harvester from a German SAK dealer I got a while ago as I liked the dove on the main blade (just happens to be my surname!), though I’m not a fan of the scales, though the blue is nice - however I was not as tidy in rivet removal and managed to mark the front scale a little
. Tapping the rivets out with a punch/drift is pretty simple. I laid all the parts out and wiped off the grease. Then I swapped the 2 blades over, and swapped the spacer and spacer with key ring hole in it over, and set to assembling the parts of the harvester with key ring together using the silver scale and some M2 tx6 bolts 6mm long, though 5 may have been better, will have to shorten my stock for the next mod, and the 11mm pivots I got from Moscow courtesy of Etsy and the supplier others have listed, and assembled my new Harvester for use in the garden, the red lanyard should help it stand out if I drop it. The assembling was not as hard as I feared it would be as the system is not in as much tension as a 91mm mod, but it still takes a bit of dexterity to keep it all together, and 2 tx6 bits are needed to help screw the package together, one either side of the knife.This left me parts for a Pioneer X with a dove on the blade, but this time I used Titanium scales (I’m a bit of Ti fan....) again via Etsy, but this time from Mike’s mods - a really nice guy to do business with, the scales came with 2 sets of blued tx6 screws, one set of 2-layer pivots, one set of 3-layer pivots and loads of super then brass washers to use as bushings between the scale and tools (alox scales have them machined in) - the only drawback is that he’s in Australia so it takes a while for stuff to arrive, but well worth the wait. This went together even more easily than the harvester. I have plans to make a magnifier to replace the can opener at some point, and I’ll share the details on that when I get to making it. But for now I now have 2 93mm mods, a Harvester with lanyard and a Ti scaled Pioneer X. I have to say that if I can do it, anyone can!


-
Nice job Rizio Il Ghiro!
Edit: I removed your first name for privacy reasons. Since we all now know your surname is "dove on the main blade" :P
-
Well done, they look great!

Sent from my SM-T387V using Tapatalk
-
Reinier, it can be a bit of a mouthful!!

-
Cheers, Acuphys 1

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login