Tread Owners Club
-
Correction, i weight
-
I have sent my Tread in for a warranty check , only had it less than 2 months. Ordered it just before my wife passed.


Sent from my iPhone using Tapatalk
-
That doesn't look good at all. -
Wow... I used my BO tread for a month and did not looked like that.
How acidic is your sweat? My grandfather had diabetes and his watches would rust-oxydise on his arm, so he went for thick large leather strap -
Finally added my knock off Tread to my Seiko watch, 6.1 oz total..heavy but functional. Without the silicon o rings it would be almost too painful to wear though. Also the o-rings give some grip that lets you turn the 1/4 inch hex wrench into a driver for hex bits.
Cheers,
H.G. -
Missed the Tread that I won in a Leatherman contest. Pondered ordering one for the last year, but it's that price ya know. Decided to bite the bullet and buy a BO Tread, and having a small engraving done. Hope the BO is okay as looked at another fella's post above and my sweat does okay with stainless steel. Had worn a SS Tread for a bit over a year and no issues, even took it on several plane trips across the USA and they airport security people told me to leave my jewelry on. LOL - Jewelry I thought, and snickered inside.
When I gave the Tread away to Tracey Ramsey, who never won a thing from any Leatherman contest, had noticed the bits actually fit a lot on the TerraTrike Rover. And I kind of miss the thing, even though the clasp would unlock itself when catching something in the hand, and the like. Hopefully Leatherman added the ball bearing spring thing on both sides, but won't hold my breath.
Probably should of stuck with SS over BO, but the price was the same, so figured 'why not?' and ordered one. Is the BO the same as the BO Surge, or is it more like the coating on a Skeletool CX? Guess will find out in the next week or two. Wished Leatherman would of stuck with the Postal Service for shipping as UPS takes literally a week+ to get from Portland, and USPS is like the next day. /sigh Ah well.
-
Okay, got my Tread in earlier this month and trying a 30 day challenge using it. This DLC Tread came in the same day as my Thorogood 1957 boots did. Was a very happy day! :D

Now, have a question. Has anyone tried using the glass breaker to, ya know, break automotive or any other type of glass with the glass breaker - yet? Seen a 7 second video of a guy using the Tread as a flail and breaking a window.
Unless the carbide glass breaker actually did the work and not the flail technique, don't think that counts.- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
-
Carrying my Tread today

-
Great pic, Ws

-
Thanks Poncho

-
-
Thanks Steve

-
What do you all do to maintain your Treads? Do you treat them with anything like Balistol? Are they prone to elemental exposure?
-
When I was drilling/dremeling out a couple of my tread links to be able to hold two more of the leatherman bits and making attachments for my new watch, I found a two small mods that I haven't seen shared and some might find useful I figured I'd share.
-
The tread clasp is pinned with a hollow rollpin. The inner dimensions of the pin will allow for a 1/16 eyeglass screw driver. At the dollar tree, I bought a small screw driver set, and cut the end of the 1/16 phillips off. From, there, it's pretty easy to file/dremel the other end to a small flathead and then you can store it in the clasp. I cut small pieces from an o-ring and punches a hole through both, putting them around the end of the driver to hold it in place. While you can't get to much purchase on it, the little screws usually don't have to be torqued down to hard, and I've been able to tight my eye glasses with just the pin tool. You can also use a little super glue to fix it in the watch, and then use the whole thing as a driver, just make sure the glue doesn't get down to the inner part of the clasp. Another note, the pin itself is 3/32, so you can replace the whole pin with the largest phillips from the same dollar tree kit (again grinding a flat head into the other end) but this driver was too large for my eyeglasses, and too small to be useful for me for other purposes.
-
The tread is hard to get a precise fit. There is not a good way to tighten or loosen the band in small increments. With my new watch, I needed to shrink the band size ~5 mm to make it a better fit for me. I was going to buy some steel and see about cutting new clutches (little things that screw into the links and hold two together) like I've seen on this thread, but an easier solution presented itself. I had noticed that an old bicycle chain I had has links that are just under 1 mm smaller than the standard links on a tread. The holes they already have in them work well with the screws, so you can just pull them apart with a chain breaker and install them. (Bike shops will give you old chain as they just send it to the recycler). They are a bit wider than the leatherman clutche, and if you store bits in the links, the chain will make it so you cannot pull them out as they overlap the edge(This can be a good thing as it can prevent you from losing them). You can address this by filing/dremeling them down as I did. I left the overlap on the end so that they prevent the bits from falling out when the watch is worn, but when you take off the watch you can fold it so the bits can be taken out. *If you replace the the clutches that hold the clasp, you will need to file down the edges as the overlap will prevent the clasp from closing otherwise.
Feel free to pm me for more details on how to do it or pictures, just figured I'd put it out there!



.jpg)
-
-
Very cool mod Trebor, thanks for sharing it

-
Bath time :)
Ps: for the moving parts lubrication i use mineral oil.
-
Great pic, Raoul
How is the Tread for you so far 
-
I used it more as jewelry on my hand, bling bling, look at me, status, etc than as utility tool. I had Not so many chances to use the tool, and when i had, their lenght, format was not a pleasure.
Used the most the simcard tool, the package opener, the bottle opener, once or twice the hex and almost never the inside key.
I always have my Squirt PS4 with me and that one is the go multitool. Plus that, i may have other multitools with me that are more easy to be used, so that is also an argument why i use it more as bling bling -
Handy to have but more of a last resort option
I can respect that :D -
Dave on Forged in Fire seems to wear a Tread quite often. Its a statement for sure.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
