Skip to content
  • Categories
  • Recent
  • Popular
  • World
Skins
  • Light
  • Dark

Collapse

NodeBB

VSAK Mini Screwdriver available in Philips?

Scheduled Pinned Locked Moved Swiss Army Knights Forum
36 Posts 1 Posters 5.7k Views
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • jph_777J
    jph_777J
    jph_777
    wrote on last edited by
    #17

    Thanks again Jothra! :salute: I followed your advice on removing the original screwdriver shaft. It worked really well. Then I cut down the mini philips shaft I had available to the longest length that would fit in the SAK's corkscrew. I inserted it into the SD handle. For a final touch, I glued the tip that was cut off of the screwdriver handle back on, to give a more finished look (see photos). I was off by a hair on realigning it, so I sanded it a bit to get it to look a little better. Next time, I think I will draw an index mark through the cut before separating the pieces, so I can realign them more easily.

    SAK_MiniPhilipsSD-5430.jpg

    SAK_MiniPhilipsSD-5440.jpg

    SAK_MiniPhilipsSD-5442.jpg

    1 Reply Last reply
    0
    • pfrsantosP
      pfrsantosP
      pfrsantos
      wrote on last edited by
      #18

      @jph_777 said:
      Thanks again Jothra! :salute: I followed your advice on removing the original screwdriver shaft. It worked really well. Then I cut down the mini philips shaft I had available to the longest length that would fit in the SAK's corkscrew. I inserted it into the SD handle. For a final touch, I glued the tip that was cut off of the screwdriver handle back on, to give a more finished look (see photos). I was off by a hair on realigning it, so I sanded it a bit to get it to look a little better. Next time, I think I will draw an index mark through the cut before separating the pieces, so I can realign them more easily.

      Well, too late now, but... if, instead of cutting the new bit, you just had it go through the plastic handle, so both ends sticked out, you could have ended with a double mini SD.

      :-[

      1 Reply Last reply
      0
      • JothraJ
        JothraJ
        Jothra
        wrote on last edited by
        #19

        @pfrsantos said:
        Well, too late now, but... if, instead of cutting the new bit, you just had it go through the plastic handle, so both ends sticked out, you could have ended with a double mini SD.

        :-[

        @jph_777 said:
        I am using a two ended screwdriver provided by Zenni Optical with their eyeglasses. It's too long to use, so I have to cut the philips end to the appropriate length.

        Nice job, jph! Reattaching the end is a nice touch.

        1 Reply Last reply
        0
        • jph_777J
          jph_777J
          jph_777
          wrote on last edited by
          #20

          Jothra and pfrsantos, Thanks again for the advice and ideas on making a double-ended mini screwdriver for the corkscrew (a mini philips on one end, and a mini slotted on other end).

          Photos below show steps taken to make one with a slightly different approach, using sandpaper instead of a knife to remove the end of the plastic handle (using 60, 100, and 220 grit sandpaper).

          Materials needed: an original VSAK mini-screwdriver, a Leatherman Eyeglass Bit, Sandpaper, pliers and a hammer.

          Photo #1: Top to bottom: Shows the original mini SD, a mini SD with the top sanded down to the point that it hits the top of the metal shaft, and a metal shaft after being removed from the handle. Once you see the flattened end of the shaft like this, it will be relatively easy to tap the shaft out of the handle.

          Photo #2: Shows relative length of the black Leatherman Eyeglass Bit to the original mini SD. At the top is the sanded down plastic handle after extracting the original bit.

          Photo #3: Shows the Leatherman Eyeglass Bit press fitted into the sanded down plastic handle, next to an original VSAK mini screwdriver.

          Photo #4: Shows the resulting double-ended SD nestled into the VSAK corkscrew. The length of the Leatherman Eyeglass Bit makes it a tight fit once the corkscrew is closed, especially if you have โ€œPlusโ€ Scales with a stainless straight pin inserted, so it is important to position it carefully before snapping the corkscrew shut, in order to not damage the SD tips.

          To extract the bit from the original SD, after sanding down the tip of the plastic handle sufficiently, I turned the mini SD upside down over a small hole in a piece of wood (the bit pointing upward). With a hammer, I just tapped on the tip of the bit to drive it out through the plastic head into the hole in the wood. Then I used pliers to pull the tip the rest of the way out, with little resistance.

          Inserting the Leatherman Eyeglass Bit was very easy, and makes a nice tight pressure fit.

          Clicking on the photos will open a larger version.

          SAK Mini Double Screwdriver-5461.jpg

          SAK Mini Double Screwdriver-5462.jpg

          SAK Mini Double Screwdriver-5464.jpg

          SAK Mini Double Screwdriver-5471.jpg

          1 Reply Last reply
          0
          • JothraJ
            JothraJ
            Jothra
            wrote on last edited by
            #21

            That looks great! It's like the old one I made, only nice and clean.

            1 Reply Last reply
            0
            • Rizio Il GhiroR
              Rizio Il GhiroR
              Rizio Il Ghiro
              wrote on last edited by
              #22

              Thatโ€™s great work! :hatsoff: :like:

              1 Reply Last reply
              0
              • pfrsantosP
                pfrsantosP
                pfrsantos
                wrote on last edited by
                #23

                @Jothra said:
                That looks great! It's like the old one I made, only nice and clean.

                And tacticool black!

                :cheers: :tu:

                1 Reply Last reply
                0
                • JothraJ
                  JothraJ
                  Jothra
                  wrote on last edited by
                  #24

                  @pfrsantos said:
                  And tacticool black!

                  :cheers: :tu:

                  I thought all the Leatherman mini glasses bits were black.

                  1 Reply Last reply
                  0
                  • S
                    S
                    SgtTowser
                    wrote on last edited by
                    #25

                    A window may have opened on turning the cork screw screw driver into a multi tool nested in a multi tool!

                    1 Reply Last reply
                    0
                    • HuntsmanH
                      HuntsmanH
                      Huntsman
                      Global Moderators
                      wrote on last edited by
                      #26

                      :like: :iagree: ๐Ÿ˜„

                      Putting a link to this thread in the SAK mod stickie thread - Will be useful for others - Thanks everyone for your contributions

                      1 Reply Last reply
                      0
                      • JothraJ
                        JothraJ
                        Jothra
                        wrote on last edited by
                        #27

                        My Leatherman micro driver bit finally arrived!

                        IMG_22092020_211755_(500_x_375_pixel).jpg

                        IMG_22092020_211928_(500_x_375_pixel).jpg

                        1 Reply Last reply
                        0
                        • cody6268C
                          cody6268C
                          cody6268
                          wrote on last edited by
                          #28

                          In my opinion, if your SAK already has scissors, it's a good case for the Rally. And, if not, Rambler or MiniChamp are good add-ons. The Phillips fits Phillips screws that are smaller than the ones the eyeglass bit can handle.

                          1 Reply Last reply
                          0
                          • JothraJ
                            JothraJ
                            Jothra
                            wrote on last edited by
                            #29

                            @cody6268 said:
                            In my opinion, if your SAK already has scissors, it's a good case for the Rally. And, if not, Rambler or MiniChamp are good add-ons. The Phillips fits Phillips screws that are smaller than the ones the eyeglass bit can handle.

                            The Rally will never fit in my corkscrew.

                            1 Reply Last reply
                            0
                            • pfrsantosP
                              pfrsantosP
                              pfrsantos
                              wrote on last edited by
                              #30

                              @Jothra said:
                              I thought all the Leatherman mini glasses bits were black.

                              They are. Don't make them less tacticool, though...

                              1 Reply Last reply
                              0
                              • ReinierR
                                ReinierR
                                Reinier
                                wrote on last edited by
                                #31

                                @Jothra said:
                                The Rally will never fit in my corkscrew.

                                1 Reply Last reply
                                0
                                • CakemonsterC
                                  CakemonsterC
                                  Cakemonster
                                  wrote on last edited by
                                  #32

                                  Finally got round to doing this. I used a Victorinox sim pin for the red handle. Completes my home made Deluxe Climber nicely.
                                  Thanks guys ๐Ÿ‘

                                  1 Reply Last reply
                                  0
                                  • pfrsantosP
                                    pfrsantosP
                                    pfrsantos
                                    wrote on last edited by
                                    #33

                                    @Cakemonster said:
                                    Finally got round to doing this. I used a Victorinox sim pin for the red handle. Completes my home made Deluxe Climber nicely.
                                    Thanks guys ๐Ÿ‘

                                    :worthless:

                                    :pok: :pok:

                                    1 Reply Last reply
                                    0
                                    • CakemonsterC
                                      CakemonsterC
                                      Cakemonster
                                      wrote on last edited by
                                      #34

                                      :salute:
                                      [attach id=0 msg=2417947]

                                      20230522_153649.jpg

                                      1 Reply Last reply
                                      0
                                      • z1913Z
                                        z1913Z
                                        z1913
                                        wrote on last edited by
                                        #35

                                        Great execution! :like:

                                        And excellent tip how to do it - I was not aware about the trick cutting off the end of the handle.

                                        I attempted something similar some time ago - replacing the mini SD with 0/00 Philips, but it did not turned out that neat. I heated up the mini driver to remove it and then drill it for the Philips. It worked, but the handle deformed slightly during the process so I had to file it to fit in the corkscrew again and the final look is rough.

                                        61B4187F-A4D4-45FB-84AB-1DEDDC95766E.jpg

                                        1 Reply Last reply
                                        0
                                        • HuntsmanH
                                          HuntsmanH
                                          Huntsman
                                          Global Moderators
                                          wrote on last edited by
                                          #36

                                          Got these of course

                                          https://www.victorinox.com/global/en/Products/Swiss-Army-Knives/Accessories/Mini-Tools-4-pieces/p/2.1201.4

                                          But I assume everyone knows about these now - Can't quite remember when they became available

                                          1 Reply Last reply
                                          0

                                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                          With your input, this post could be even better ๐Ÿ’—

                                          Register Login

                                          • Login

                                          • Don't have an account? Register

                                          • First post
                                            Last post
                                          0
                                          • Categories
                                          • Recent
                                          • Popular
                                          • World