What did you use your Sak on today?
-
cody6268
Good idea on that bucket carry!!!
I am copying that!!!
-
@Zanza said:
Lunchtime with my Swisschamp cutting in half a Nigiri
All in good fun since we're all friends here... There are so many cultural faux pas in this one photograph.

I'll spare you the details, but suffice it to say that Comis will need a long vacation if he sees this. I shudder to think what would happen if you encountered the yanagi welding sushi chef while you were eating. Even your trusty Swiss Army knife couldn't protect you from the yanagi. ;) -
Used the small blade on my SwissChamp to score some wooden shims to level out a railing post, then the ruler in the fish scaler for a quick measurement rather than look for the measuring tape. The blade on my RangerGrip 55 help make some fatwood shavings for the fire pit later tonight.
-
Opened a hard boiled egg with my XLT. Used the bit driver with the PH2-bit. Worked as expected.
Will try it again tomorrow with a different bit.
-
Amongst other things used the waiter to open box for new sheath

Sent from my iPhone using Tapatalk
-
Tinker small blade to cut a switchboard masking panel, Pioneer awl to scrape the edges up nice and smooth
-
Handy uses ALL !!!

-
@ulzhan said:
Opened a hard boiled egg with my XLT. Used the bit driver with the PH2-bit. Worked as expected.Will try it again tomorrow with a different bit.
ulzhan, do I hear a new challenge idea? The Hard Boiled Egg Challenge: Open a hard boiled egg each day with a different tool on the SAK of your choice until you've used all the implements on that model? And of course there would have to be a badge.
-
@Kraken said:
ulzhan, do I hear a new challenge idea? The Hard Boiled Egg Challenge: Open a hard boiled egg each day with a different tool on the SAK of your choice until you've used all the implements on that model? And of course there would have to be a badge.Oh yes!
That'll Take some weeks with the XLT...
-
The Swiss Champ came to the rescue last night. I was short a marshmallow roasting stick for the number of kids we had for our campfire. Off to the woods behind the house and used the saw to cut a small branch from a fallen oak, then the main blade to sharpen the end. The kids only used them for a couple of rounds and left the adults to finish the bag!
-
-
@Kraken said:
The Swiss Champ came to the rescue last night. I was short a marshmallow roasting stick for the number of kids we had for our campfire. Off to the woods behind the house and used the saw to cut a small branch from a fallen oak, then the main blade to sharpen the end. The kids only used them for a couple of rounds and left the adults to finish the bag!Top notch use chap

-
@munsonhsr said:
Broke down and bought a new weed trimmer. Lots of screws....not a problem for my Evo 18.
Nice one!
The Evo s 18 is on my wish list.
It looks like it brings the best out of both worlds (victorinox/Wenger)Sendt fra min moto g(8) power med Tapatalk
-
@munsonhsr said:
Broke down and bought a new weed trimmer. Lots of screws....not a problem for my Evo 18.

-
Used Champion Plus metal file for finger nail file. Worked great! May file puppy’s needle teeth next. NEVER! Just joking. But man can he punch holes with baby teeth.

-
We’ve picked up my lady’s old PC and before giving it to her friends she asked me to remove the hard drive. Used inline Phillips on a Work Champ right at the parking lot

Half an hour later used scissors to unpack two upgrade kits for my Fender Telecaster jack socket - one is chrome and one is nickel. Never knew which one would fit better, so ordered both. In case you are interested- it’s nickel for my AmStd Tele [emoji56]

Hopefully I’ll install it tomorrow and will never have issues with those loud cracking sounds stock jacket socket makes [emoji1695]
-
@alexanderre said:
We’ve picked up my lady’s old PC and before giving it to her friends she asked me to remove the hard drive. Used inline Phillips on a Work Champ right at the parking lot

Half an hour later used scissors to unpack two upgrade kits for my Fender Telecaster jack socket - one is chrome and one is nickel. Never knew which one would fit better, so ordered both. In case you are interested- it’s nickel for my AmStd Tele [emoji56]

Hopefully I’ll install it tomorrow and will never have issues with those loud cracking sounds stock jacket socket makes [emoji1695]
So here I go with the installation. Spoiler: it turned out to be way easier than I expected, though never seemed as a tough one to handle anyway [emoji1316]
First thing first I used pliers to undo the nut holding an old socket in place

Then unscrewed the control plate to reach the socket from the inside

A new socket just screws on top of the standard Switchcraft jack and is thick enough so you don’t have to remove any of the stock parts - just screw it on
Here I used pliers again to tighten it up and align properly

Then just get in fixed in place by those two screws

P.S.: honestly speaking I dropped one of the screws during this stage right into the jack socket hole, so had to undo the control plate and grab the screw with the pliers to try once more [emoji23]

All in all it takes less than 10 minutes to have your Telecaster jack socket fixed like forever [emoji1695][emoji1316]
P.P.S.: after I’ve done all the steps I checked the result again to see if I have the replacement cap screwed in line with the body of the guitar and to my surprise it wasn’t. Additional examination showed that it’s not my fault - the part has misaligned screw holes, so it’ll be that way [emoji2371]

-
@alexanderre said:
So here I go with the installation. Spoiler: it turned out to be way easier than I expected, though never seemed as a tough one to handle anyway [emoji1316]First thing first I used pliers to undo the nut holding an old socket in place

Then unscrewed the control plate to reach the socket from the inside

A new socket just screws on top of the standard Switchcraft jack and is thick enough so you don’t have to remove any of the stock parts - just screw it on
Here I used pliers again to tighten it up and align properly

Then just get in fixed in place by those two screws

P.S.: honestly speaking I dropped one of the screws during this stage right into the jack socket hole, so had to undo the control plate and grab the screw with the pliers to try once more [emoji23]

All in all it takes less than 10 minutes to have your Telecaster jack socket fixed like forever [emoji1695][emoji1316]
P.P.S.: after I’ve done all the steps I checked the result again to see if I have the replacement cap screwed in line with the body of the guitar and to my surprise it wasn’t. Additional examination showed that it’s not my fault - the part has misaligned screw holes, so it’ll be that way [emoji2371]


Nice work and great Tele

I'"m a Strat man myself, but love Tele's too, must get me one (or two) someday... :D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login