What did you use your Sak on today?
-
Used the blade and the reamer to clean out some breakouts on the switchboard and then the large driver/opener to crank in a catenary wire anchor to a bit of 2x 4

-
Measured twice. Cut once.
Once with the fish scale.
Once with the tape.

-
@SgtTowser said:
Measured twice. Cut once.Once with the fish scale.
Once with the tape.
I always thought it was 'Measures once, cuss twice'
Pretty sure your method produces a lot less waste too; I'm going to have to give it a try!We rented a small skiff this weekend to tour some of the back waterways and the Swiss Champ's main blade cut open a package of bait for fishing. Unfortunately, the hook disgorger on the fish scaler and the pliers didn't get any use as I had hoped. Carrying the SC on a pocket dangler clip at work today to test the feasibility of using it as my work EDC to replace my Explorer. I'll give it a run for the week and see how it goes. Used the Minichamp's cut & picker blade to score the outer sheath of some data cable I have to terminate. I pinched the cable between the blade and the body, gave the MC a few twists with just the slightest pressure and the wire covering slides right off without any damage to the wires underneath.
-
...I opened an envelope with the Classic blade...

-
Just used the sharp edge of my SwissTool SpiritX as a screwdriver to fasten the lose screws of gf's sunglasses (wish I had my LM Wave with me) and received plus bf points :)))
-
@ddogu said:
Just used the sharp edge of my SwissTool SpiritX as a screwdriver to fasten the lose screws of gf's sunglasses (wish I had my LM Wave with me) and received plus bf points :)))Improvisation is fun! Years ago, before I had a micro SD on any of my SAKs..... I used the chisel on my Champion more times than I can count to tighten screws on eyeglasses. I can remember when I was a teenager... I would break my eyeglasses all the time.
-
I made a unique little Yellowjacket killer, used a tea container and cut a slit in one side then a hole in another so I could hook up a special wet vac that I left soapy water in so that when they got sucked in they drowned, did three rounds and killed about 300, but that’s what I needed the sak for, then made another setup so it’s ready to go for the next time,,
JR


-
@MadPlumbarian said:
I made a unique little Yellowjacket killer, used a tea container and cut a slit in one side then a hole in another so I could hook up a special wet vac that I left soapy water in so that when they got sucked in they drowned, did three rounds and killed about 300, but that’s what I needed the sak for, then made another setup so it’s ready to go for the next time,,
JR
-
In light of MadPlumbarian's yellow jacket harvesting machine, my SAK use today was no where near as awesome, but it was fun. I had to get in to an office that was recently vacated to pick up some equipment before the new tenants moved in, but the door was locked. I remember the previous occupant telling me that he could just use his ID badge to slide between the jamb and the latch bolt and open the door. Seeing as I didn't want to walk all the way back down to the security desk to ask for someone with a key to let me in, I took out my Explorer and tried to use the main blade to manipulate the latch bolt. It took a little more force than I was comfortable putting the blade through, so I switched to the cap lifter and lo and behold it worked like a charm! I felt like my childhood hero, Saint Angus (MacGyver), patron saint of improvised solutions.
-
@Kraken said:
In light of MadPlumbarian's yellow jacket harvesting machine, my SAK use today was no where near as awesome, but it was fun. I had to get in to an office that was recently vacated to pick up some equipment before the new tenants moved in, but the door was locked. I remember the previous occupant telling me that he could just use his ID badge to slide between the jamb and the latch bolt and open the door. Seeing as I didn't want to walk all the way back down to the security desk to ask for someone with a key to let me in, I took out my Explorer and tried to use the main blade to manipulate the latch bolt. It took a little more force than I was comfortable putting the blade through, so I switched to the cap lifter and lo and behold it worked like a charm! I felt like my childhood hero, Saint Angus (MacGyver), patron saint of improvised solutions.Nice one. It's times like these that I like to have a Swisschamp or champion ... The scaler is great for that sort of thing.
-
@ElevenBlade said:
Nice one. It's times like these that I like to have a Swisschamp or champion ... The scaler is great for that sort of thing.I would have to agree with you. I have a new to me SC inbound this week along with a belt pouch so it doesn't drag my trousers down riding in my pocket.
-
Fixing a laptop. Again :)

-

Snowblower maintenance for the upcoming events. Sometimes I don’t want to get up to grab a Phillips!Sent from my iPhone using Tapatalk
-
...the humble Classic SD on the mail.....
-
Recruit small blade to cut a cable tie to allow removal of a blocked submersible pump , open up some plastic tubs , and caplifter to scrape mud from the tread on my boots . Tweezers to remove a couple of stray hairs
-
I used my Hiker plus to share some food with my dog on a hike [emoji190]

Sendt fra min moto g(8) power med Tapatalk
-
It looks more like HE/SHE shared with you :D

-
@SirVicaLot said:
It looks more like HE/SHE shared with you :D
She sure think she is the boss ! And thanks @Mini [emoji482]
Sendt fra min moto g(8) power med Tapatalk
-
For the first time I had actual use for the CS driver. I usually carry my alox mod but for some reason I picked the 91mm cousin today. The kids wanted to play pokemon go and we headed out to a good area that has a lot of those and is surrounded with forest. My doughter tried out a new case for her phone that has a lot of aluminum and is screwed together with small hex bolts. Aluminium, weak GPS antenna, forest and clouds are not a great combo!
We forgot the key to the case at home and she could not get a good enough signal to play and guess what? The SC driver work on those tiny hexbolts to free her phone from its Faraday prison. Happy kid and happy dad who picked the right SAK for the day

[It's not failure if you learn something from it]
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
