What did you use your Leatherman for today?
-
Another GB resto, and obvious LMN was there

-
Label removing [emoji1689]
Sent from my SM-G960F using Tapatalk

-
I had to remove the the fridge-freezer and dishwasher today (in advance of replacements tommorow)
The new (to me) Rebar, courtesy of Aloha
helped cut the power cables, to prevent re-use by Darwin award candidates 
I then discovered that my fan (we don't really do A/C here in the UK) had died.
The Squirt helped to remove/replace things (fuse etc.) but a non-starter

A double LM sort of day


-
Great uses, Surge
Sorry to hear about the fan troubles :ahhh We have to do AC here (my area of the US) or else it would be unbearable :ahhh :ahhh :ahhh :D -
Stopped by my parents house to discover that they were going to try and extract a broken bulb from the fixture with a potato... 2 minutes later the Rebar had it out with no weird potato residue involved:

-
Great use
and 1 that I have also had to use as well 
-
@GearedForwards said:
Stopped by my parents house to discover that they were going to try and extract a broken bulb from the fixture with a potato... 2 minutes later the Rebar had it out with no weird potato residue involved:
Good to know that you "chipped" in

-
It's been a slow few days in the house of Surge; mostly delivery nightmares (new fridge-freezer & dishwasher) :ahhh
However, I finally managed to pick up a book I'd ordered and the Rebar helped free it from its packaging

-
Again used the Squirt to trim electrical wires. Have no clue why i havent went for the ES version. Used old light bulbs and the heat fried the tiny lamp cables. I have mounted new ones, cables are thicker and slot is ceramic, plus LED bulbs, i should be fine now

-
Yesterday (25th) I used my new Rebar (cheers Aloha
) and my FX to help a mate put up a couple of new trellis, attached to their existing fence.The Rebar helped to remove the old Sky-Hooks, which were holding up something else, and the FX and it's Awlsome attachment made new holes.
It all went swimmingly well




-
Been a busy one yesterday.
Some time ago I posted a few pics of fixing a kitchen heating water tap. It still misbehaved once in a while so we finally decided to replace it. Down under the sink I went with a Signal in my hand attempting to undo a nut holding the water pipe in place

But the handle splay is so wide on Signal that I had to switch to the Wave [emoji2371]

Next I used Work Champ long Phillips to install a wall plug to a new heater - they do provide it but since there are options to either plug it above or below the sink you have to install it yourself

Being done with a water heater I went further to replacing water filter cartridges. Work Champ main blade was used to unpack all the parts and cut thing plastic water pipes, though I didn’t take any pictures of that.
However in order to install a new membrane I needed to first remove the old one, so Work Champ pliers were used

After quite some time fiddling with the reverse osmosis system and putting it all back to work providing us with fresh water I decided to have a look what might possibly be wrong with the old heating water tap, so Phillips on a Work Champ was used again. Can’t stress enough how much I love that long one and the reach it provides - impossible to do with anything else like LMs, CyberTools etc.

As you can see it’s all wrong and I could possibly clean it and make it work for some more time, but at the price of 30-50$ replacement I just don’t see the point....
Anyways, I had my fun doing it all, hope you did too reading through all of the above [emoji736]
-
Nice uses !

-
I've used the old giftcard trick for ductape for years but always liked the idea of making a more compact roll, so I took my Rebar to a nail: sawing off the point, filing the tip flat and any burrs off, then came the frustrating part. Trying to roll duct tape neatly is an exercise in self torture




Came it pretty well in the end though! and I do say I love having ready access to a metal saw

-
Great use, GF
I have done this before with the duct tape and the nail as well
anytime you can carry duct tape easily and in a very small space is always a win 
-
Did some carving.


-
Built a small shelf today. Used the Surge's file to clean up edges, the large flat screw driver opened a can of wood stain, and the pliers were used to hold a piece of pvc while heating it over a torch (then formed into a 90° bracket, used to secure the shelf to the wall).



-
PST helped me with some hot stuff. I swapped some joysticks on a controller. Things get damn hot


-
Use my Rebar and a couple of paper clips to make a hook for my no touch tool (trying to up my EDC sleeping area). Just need to wide the hook a little and retie the lanyard since the one it shipped on untied.


-
Used my sidekick to loosen and tighten tiny nuts. Between the Sidekick and 4" adjustable, got it all tightened.
Swapped out a sensor on the flat sorter

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login