What did you use your Sak on today?
-
Reinier,
I am getting serious Cybertool envy again. May have to spring for one. Which one of the Cybertools do you recommend, if you don’t mind me asking? Thanks in advance.
-
Kraken,
Yes, I am getting use. But who ever heard of a flash light lanyard hole cracking open, when pulling it out of one’s pocket on a key chain? I bought the little Fenix on the recommendation of the fellow at Everyday Commentary, when it first came out, and I have gotten a lot of good out of it, but quite a freakish design failure. Anyway, I am now looking for a new keychain light with some throw force like the little Fenix. I want to go back to a more slender form factor and I want to be able to have a charging port, where I do not have to remove the battery to re-charge. I’m looking for something in the $40-60 range, not the $100-200 range. I want a flashlight. Not a mortgagelight. :D
-
Echotech,
There ought to be a scientific, or anthropological, term for using a tool to access more tools of the same class of tools.
And it ought not be collecting, or obsession. :D
-
@SgtTowser said:
Kraken,Yes, I am getting use. But who ever heard of a flash light lanyard hole cracking open, when pulling it out of one’s pocket on a key chain? I bought the little Fenix on the recommendation of the fellow at Everyday Commentary, when it first came out, and I have gotten a lot of good out of it, but quite a freakish design failure. Anyway, I am now looking for a new keychain light with some throw force like the little Fenix. I want to go back to a more slender form factor and I want to be able to have a charging port, where I do not have to remove the battery to re-charge. I’m looking for something in the $40-60 range, not the $100-200 range. I want a flashlight. Not a mortgagelight. :D
How often are you using the light and for how long typically? I highly recommend Olight and Lumintop, but the specific models depend on your use cases and if you actually want it to like on your keychain.
-
Geared forward
Thanks for the suggestions. I like it on the key ring with an easy remove clip. I will check those two brands out.
-
@SgtTowser said:
Echotech,There ought to be a scientific, or anthropological, term for using a tool to access more tools of the same class of tools.
And it ought not be collecting, or obsession. :D
Agree ST
Sakloopparadoxacology
hmmm not sure that’s going to catch on but best I can come up with for now


echo
Sent from my iPhone using Tapatalk
-
Executive...everything!!
-
Hiker helping with a spot of garden tidying, removing dead branches, and stopping the ivy killing the tree with the saw and digging out the roots of weeds from the brickwork with the can opener




Sent from my iPhone using Tapatalk
-
@SgtTowser said:
Reinier,I am getting serious Cybertool envy again. May have to spring for one. Which one of the Cybertools do you recommend, if you don’t mind me asking? Thanks in advance.
For me it will always be the 34 (currently known as Cybertool M). I like to have scissors which the smallest model lacks. Also, on the S or 29 I think the main blade nail nick is a bit hard to access due to the bit driver being in the way.
The L and Lite have a few tools I rarely use or need. Maybe if you need a metal saw the 41 is the one for you. I used to have one (maybe two
) but I never used it. It's a bit (pun intended) too big and heavy for me. -
Yesterday (25th) I used my new Rebar (cheers Aloha
) and my <u>FX</u> to help a mate put up a couple of new trellis, attached to their existing fence.The Rebar helped to remove the old Sky-Hooks, which were holding up something else, and the FX and it's Awlsome attachment made new holes.
It all went swimmingly well




-
Champion is a good paint can opener.

-
Champion plus inline Phillips to the rescue—changed batteries on an old Snap-on key ring multitool with a light that I keep in the map pocket of my Vehicle.

-
Gotta love that inline Philips driver; I think it's more capable than the backside Philips and a major reason I EDC an Explorer.
-
Kool uses all!!!

-
Been a busy one yesterday.
Some time ago I posted a few pics of fixing a kitchen heating water tap. It still misbehaved once in a while so we finally decided to replace it. Down under the sink I went with a Signal in my hand attempting to undo a nut holding the water pipe in place

But the handle splay is so wide on Signal that I had to switch to the Wave [emoji2371]

Next I used Work Champ long Phillips to install a wall plug to a new heater - they do provide it but since there are options to either plug it above or below the sink you have to install it yourself

Being done with a water heater I went further to replacing water filter cartridges. Work Champ main blade was used to unpack all the parts and cut thing plastic water pipes, though I didn’t take any pictures of that.
However in order to install a new membrane I needed to first remove the old one, so Work Champ pliers were used

After quite some time fiddling with the reverse osmosis system and putting it all back to work providing us with fresh water I decided to have a look what might possibly be wrong with the old heating water tap, so Phillips on a Work Champ was used again. Can’t stress enough how much I love that long one and the reach it provides - impossible to do with anything else like LMs, CyberTools etc.

As you can see it’s all wrong and I could possibly clean it and make it work for some more time, but at the price of 30-50$ replacement I just don’t see the point....
Anyways, I had my fun doing it all, hope you did too reading through all of the above [emoji736]
-
Kudos! It Was fun reading!

Sent from my SM-T387V using Tapatalk
-
@alexanderre said:
Been a busy one yesterday.Some time ago I posted a few pics of fixing a kitchen heating water tap. It still misbehaved once in a while so we finally decided to replace it. Down under the sink I went with a Signal in my hand attempting to undo a nut holding the water pipe in place

But the handle splay is so wide on Signal that I had to switch to the Wave [emoji2371]

Next I used Work Champ long Phillips to install a wall plug to a new heater - they do provide it but since there are options to either plug it above or below the sink you have to install it yourself

Being done with a water heater I went further to replacing water filter cartridges. Work Champ main blade was used to unpack all the parts and cut thing plastic water pipes, though I didn’t take any pictures of that.
However in order to install a new membrane I needed to first remove the old one, so Work Champ pliers were used

After quite some time fiddling with the reverse osmosis system and putting it all back to work providing us with fresh water I decided to have a look what might possibly be wrong with the old heating water tap, so Phillips on a Work Champ was used again. Can’t stress enough how much I love that long one and the reach it provides - impossible to do with anything else like LMs, CyberTools etc.

As you can see it’s all wrong and I could possibly clean it and make it work for some more time, but at the price of 30-50$ replacement I just don’t see the point....
Anyways, I had my fun doing it all, hope you did too reading through all of the above [emoji736]
Great use of the Work Champ alexanderre! Makes me wonder if my Swiss Champ would've been up to the task or if I should start looking in to getting a Work Champ, you know, just in case.
-
Thanks, guys [emoji1317]
Oh, I’ve been thinking about getting a Swiss Champ actually, especially since there’s a topic going on SC vs CyberTool now, but that long slim Phillips is a game changer for me - I won’t be able to disassemble that old heater and many more things without it [emoji2371]
-
@alexanderre said:
Thanks, guys [emoji1317]Oh, I’ve been thinking about getting a Swiss Champ actually, especially since there’s a topic going on SC vs CyberTool now, but that long slim Phillips is a game changer for me - I won’t be able to disassemble that old heater and many more things without it [emoji2371]
I'm in the SwissChamp camp, but wouldnt the CyberTool give you a longer, slimmer phillips?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
