What did you use your Sak on today?
-
Kool uses all!!!

-
Been a busy one yesterday.
Some time ago I posted a few pics of fixing a kitchen heating water tap. It still misbehaved once in a while so we finally decided to replace it. Down under the sink I went with a Signal in my hand attempting to undo a nut holding the water pipe in place

But the handle splay is so wide on Signal that I had to switch to the Wave [emoji2371]

Next I used Work Champ long Phillips to install a wall plug to a new heater - they do provide it but since there are options to either plug it above or below the sink you have to install it yourself

Being done with a water heater I went further to replacing water filter cartridges. Work Champ main blade was used to unpack all the parts and cut thing plastic water pipes, though I didn’t take any pictures of that.
However in order to install a new membrane I needed to first remove the old one, so Work Champ pliers were used

After quite some time fiddling with the reverse osmosis system and putting it all back to work providing us with fresh water I decided to have a look what might possibly be wrong with the old heating water tap, so Phillips on a Work Champ was used again. Can’t stress enough how much I love that long one and the reach it provides - impossible to do with anything else like LMs, CyberTools etc.

As you can see it’s all wrong and I could possibly clean it and make it work for some more time, but at the price of 30-50$ replacement I just don’t see the point....
Anyways, I had my fun doing it all, hope you did too reading through all of the above [emoji736]
-
Kudos! It Was fun reading!

Sent from my SM-T387V using Tapatalk
-
@alexanderre said:
Been a busy one yesterday.Some time ago I posted a few pics of fixing a kitchen heating water tap. It still misbehaved once in a while so we finally decided to replace it. Down under the sink I went with a Signal in my hand attempting to undo a nut holding the water pipe in place

But the handle splay is so wide on Signal that I had to switch to the Wave [emoji2371]

Next I used Work Champ long Phillips to install a wall plug to a new heater - they do provide it but since there are options to either plug it above or below the sink you have to install it yourself

Being done with a water heater I went further to replacing water filter cartridges. Work Champ main blade was used to unpack all the parts and cut thing plastic water pipes, though I didn’t take any pictures of that.
However in order to install a new membrane I needed to first remove the old one, so Work Champ pliers were used

After quite some time fiddling with the reverse osmosis system and putting it all back to work providing us with fresh water I decided to have a look what might possibly be wrong with the old heating water tap, so Phillips on a Work Champ was used again. Can’t stress enough how much I love that long one and the reach it provides - impossible to do with anything else like LMs, CyberTools etc.

As you can see it’s all wrong and I could possibly clean it and make it work for some more time, but at the price of 30-50$ replacement I just don’t see the point....
Anyways, I had my fun doing it all, hope you did too reading through all of the above [emoji736]
Great use of the Work Champ alexanderre! Makes me wonder if my Swiss Champ would've been up to the task or if I should start looking in to getting a Work Champ, you know, just in case.
-
Thanks, guys [emoji1317]
Oh, I’ve been thinking about getting a Swiss Champ actually, especially since there’s a topic going on SC vs CyberTool now, but that long slim Phillips is a game changer for me - I won’t be able to disassemble that old heater and many more things without it [emoji2371]
-
@alexanderre said:
Thanks, guys [emoji1317]Oh, I’ve been thinking about getting a Swiss Champ actually, especially since there’s a topic going on SC vs CyberTool now, but that long slim Phillips is a game changer for me - I won’t be able to disassemble that old heater and many more things without it [emoji2371]
I'm in the SwissChamp camp, but wouldnt the CyberTool give you a longer, slimmer phillips?
-
Construction adhesive unclogger

-
Great use of the corkscrew Reinier!

-
Thanks :)
-
@alexanderre said:
Been a busy one yesterday.Some time ago I posted a few pics of fixing a kitchen heating water tap. It still misbehaved once in a while so we finally decided to replace it. Down under the sink I went with a Signal in my hand attempting to undo a nut holding the water pipe in place

But the handle splay is so wide on Signal that I had to switch to the Wave [emoji2371]

Next I used Work Champ long Phillips to install a wall plug to a new heater - they do provide it but since there are options to either plug it above or below the sink you have to install it yourself

Being done with a water heater I went further to replacing water filter cartridges. Work Champ main blade was used to unpack all the parts and cut thing plastic water pipes, though I didn’t take any pictures of that.
However in order to install a new membrane I needed to first remove the old one, so Work Champ pliers were used

After quite some time fiddling with the reverse osmosis system and putting it all back to work providing us with fresh water I decided to have a look what might possibly be wrong with the old heating water tap, so Phillips on a Work Champ was used again. Can’t stress enough how much I love that long one and the reach it provides - impossible to do with anything else like LMs, CyberTools etc.

As you can see it’s all wrong and I could possibly clean it and make it work for some more time, but at the price of 30-50$ replacement I just don’t see the point....
Anyways, I had my fun doing it all, hope you did too reading through all of the above [emoji736]
Wow, you have done some great work!
-
@ElevenBlade said:
I'm in the SwissChamp camp, but wouldnt the CyberTool give you a longer, slimmer phillips?Nope, unfortunately not at all - the bit adapter adds the unwanted for me thickness to the construction


I mean the long slim Phillips on a Work Champ just in case
-
@alexanderre said:
That’s the trick I should bookmark [emoji1303]And it actually worked perfectly!
-
Pool sweeper went on fritz. I had left my thrift store Explorer with the broken scale on the fire ring by the pool earlier to dry out after giving it a second bath. Took the old Explorer in the pool. Third bath. In Line Phillips handled all the screws needing disassembly for diagnosis without me having to leave the pool. Then I sat on the pool steps and unstuck an obstruction in the passenger side gear housing. Then reassembled. Then took Sweep to patio table for tread replacement, because that’s where I had left them yesterday. Then reconnected sweep. Then had lemonade, because that’s what you drink, when life supplies lemons. Then decided this old Explorer is now my dedicated pool knife as is!!! I owe it a good home—mine. New scales? It don’t need no stinking new scales!!! Will start wearing my board shorts with pocket and carry the Explorer in the pool. We will see how long it takes for pool water to eat cellodon.

-
I fished out an old opened and barely used bottle of Glenlivet Nadurra (do prefer my 'livet in standard 12 guise or sometimes the archive 21 so this hasn't been touched in quite some time) and the cork broke in half like they sometimes do.
The corkscrew of SC was used in order to get half of cork out. Unfortunately the cork was so rotten than I ended up pushing most of it into the bottle.
Reckon the remaining 1/4 of the cork that remained will not not stop the whisky from vaporing for very long so I might be drinking more Nadurra in the near future ;)
Lähetetty minun SM-T515 laitteesta Tapatalkilla
-
The wastage of any Livet is a tragedy of Shakespearean proportion. And the Scottish side of my clan might wage war over it.
-
Alexanderre
You have flung me into the abyss of analysis paralysis. I had almost resolved to buy a work champ, and now this logic of greater reach with Cybertool grips me.
-
@SgtTowser said:
AlexanderreYou have flung me into the abyss of analysis paralysis. I had almost resolved to buy a work champ, and now this logic of greater reach with Cybertool grips me.
Oops [emoji51] Though it’s all up to your needs - for me Cybertool has less reach that a slim Phillips on a Work Champ - I need it to be slim and get into tight places. If width and depth of the screw hole is not important to you - get a Cybertool [emoji1303]
(Though you might regret it because Work Champ has a larger blade which is also locking and so on [emoji23])
-
@alexanderre said:
Oops [emoji51] Though it’s all up to your needs - for me Cybertool has less reach that a slim Phillips on a Work Champ - I need it to be slim and get into tight places. If width and depth of the screw hole is not important to you - get a Cybertool [emoji1303](Though you might regret it because Work Champ has a larger blade which is also locking and so on [emoji23])
Is it the socket for the bit itself that is too wide? It appears long enough.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
