Skary Skeletool October Challenge?
-
Day 7
Not a lot doing today.

-
Day 7
In addition to the usual package opening and snack cutting, I used the Skeletool with an Allen bit from the LM bit kit to do some adjustments to my water rower.

This was my first time using a LM flat Allen bit. It did work, but I noticed that because of the tip being modified to make it flat, it doesn’t grip as nicely as a hex bit or Allen wrench. -
@Alan K. said:
- I found the hammer adapters on line and they are around $30.00 U.S. so too pricey for me, but I still think they are a great idea.
I was considering doing a giveaway as part of this challenge and so now I have decided. It will be winner’s choice of one of the hammer or wedge adapters for the Skeletool.
To be entered in the GAW, post a picture of the Skeletool with a Halloween or Fall decoration saying that it is your GAW pic. I will randomly select the winner on October 31st - Halloween.
-
Very Nice, Sos24!

-
:o must make Fall pics :ahhh :ahhh :ahhh Very generous, Sos

And thanks Nix

-
Day 8:
Opening parts


Sent fra min FRD-L09 via Tapatalk
-
-
Day 8

After fumbling through all my knife accessories for a while, I re-discovered I do have rounded sharpening rod from the Lansky turnbox. So few minutes later, I get rid of the rolled part and kinda restore the serration.
@chip said:
The Edge on the scallops of the serrated sectIon must be a lot weeker than the plain edge due to having less than half the inclusive angle due to being ground shallower and only on one side.They are normally protected from hard surfaces (when cutting on a board) by the points.
Chip, I definitely agree what said. Most serration I have are mostly chisel grinded on one side only, and depending on steel and the geometry, they often could be rather weak and that's probably why I have the roll on mine even without much heavy use. Obviously some scallop is better than others, for example, I really love the 'serration' on Victorinox pairing knife, those serration last a century and I have never heard of anyone needing to sharpen them.@Nix said:
Chip's fault. As you can see in this thread: I've lost the plot
If there is one thing MTO is not short of is probably motivators. :D >:D
-
Powernoodle Day 8
*
Opening Amazon boxes, and deconstructing them for disposal, is the primary duty of my EDC blades.* -
@Pauldmmwc said:
Hello Day 8
So I wanted to change the battery in the kitchen clock and of course I dropped it and broke the case that holds the battery in place.
I thought some duct tape would hold the battery in place firmly so would make proper contact and we would know what time it is.
That did not work so out with some small cable ties and she is all zipped up tight and working properly now.
Skele to cut off the excess bits of tie.
Good fix!

@Sos24 said:
I was considering doing a giveaway as part of this challenge and so now I have decided. It will be winner’s choice of one of the hammer or wedge adapters for the Skeletool.To be entered in the GAW, post a picture of the Skeletool with a Halloween or Fall decoration saying that it is your GAW pic. I will randomly select the winner on October 31st - Halloween.
Very generous of you!

@powernoodle said:
Powernoodle Day 8
*
Opening Amazon boxes, and deconstructing them for disposal, is the primary duty of my EDC blades.*That's one sharp looking Skeley!

-
<u>DAY 8</u>
A slow one with no reason to go out, apart from work (where I can't use the CX) ::)
That said, it's been a reasonably sunny afternoon here in London so, here's a "Skele & Shades" shot 8)

-
Some great shots, today.
Nice bench, Surge. Reminds me of a sunflower.

-
-
Well, it is now damned cheerful. :D
-
-
@Sos24 said:
I was considering doing a giveaway as part of this challenge and so now I have decided. It will be winner’s choice of one of the hammer or wedge adapters for the Skeletool.To be entered in the GAW, post a picture of the Skeletool with a Halloween or Fall decoration saying that it is your GAW pic. I will randomly select the winner on October 31st - Halloween.
Very generous

Sent fra min FRD-L09 via Tapatalk
-
Day 8 of 30
Today sharpened my Skeletool blade with wetsandpapers. Blade wasnt awful dull but still needed sharpening.

Only Tools Matters
-
Day 8
Skeletool cut a couple dog chews in half.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



